When I load with modprobe the dmx3191d module, the module load fine. But when I try to access to the scanner atteched to the card, xsane hang. I try in console to find the scanner (UMAX Astra 1200S) with the sane-find-scanner script and he didn't found anything. Sometime the command just hang instate to found nothing and sometime, he can find the scanner (but not always). Reproducible: Always Steps to Reproduce: 1. Compile your kernel with SCSI and SG hard 2. Make DMX3191D in module 3. restart with the new kernel and lauch sane-find-scanner Actual Results: sane-find-scanner found most of time the scanner, xsane hang and after 2 or 3 minute when I try to numerise and the kernel become in panic, all the system crash Expected Results: juste work and stop hang or crash or whatever I have try all kernel from 2.6.x tree (from 2.6.0 to 2.6.11, vanilla and gentoo- dev-sources) and he always do the same error. From 2.6.0 to 2.6.9, the kernel always make a "Kernel Panic". But with 2.6.10 and 2.6.11, the module loaded but it is when I have to access to the scanner, the system hang and the kernel make a panic message
Please post the output of "emerge info" to every bug you submit. Is the system usable after the oops? If so, please attach the "dmesg" output after the oops has occurred.
0000:00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02) Subsystem: ASUSTeK Computer Inc. TUSL2-C Mainboard Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Region 0: Memory at f8000000 (32-bit, prefetchable) Capabilities: [88] #09 [f104] Capabilities: [a0] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> 0000:00:01.0 PCI bridge: Intel Corporation 82815 815 Chipset AGP Bridge (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000dfff Memory behind bridge: ee000000-efdfffff Prefetchable memory behind bridge: eff00000-f7ffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- 0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000b000-0000dfff Memory behind bridge: ec000000-edffffff Prefetchable memory behind bridge: efe00000-efefffff BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- 0000:00:1f.0 ISA bridge: Intel Corporation 82801BA ISA Bridge (LPC) (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 0000:00:1f.1 IDE interface: Intel Corporation 82801BA IDE U100 (rev 02) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. TUSL2-C Mainboard Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 4: I/O ports at a800 [size=16] 0000:00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. TUSL2-C Mainboard Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at a400 [size=32] 0000:00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus (rev 02) Subsystem: ASUSTeK Computer Inc. TUSL2-C Mainboard Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at e800 [size=16] 0000:00:1f.4 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #2) (rev 02) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. TUSL2-C Mainboard Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 9 Region 4: I/O ports at a000 [size=32] 0000:01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2) (prog-if 00 [VGA]) Subsystem: ASUSTeK Computer Inc.: Unknown device 8063 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=effe0000] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at 00020000 [disabled] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> 0000:02:0b.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 0c) Subsystem: Intel Corporation EtherExpress PRO/100 S Desktop Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 9 Region 0: Memory at ed800000 (32-bit, non-prefetchable) Region 1: I/O ports at d800 [size=64] Region 2: Memory at ed000000 (32-bit, non-prefetchable) [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=2 PME- 0000:02:0c.0 SCSI storage controller: DTC Technology Corp. Domex 536 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at d400 0000:02:0d.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04) Subsystem: Creative Labs SB0240 Audigy 2 Platinum 6.1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at d000 Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:02:0d.1 Input device controller: Creative Labs SB Audigy MIDI/Game port (rev 04) Subsystem: Creative Labs SB Audigy MIDI/Game Port Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at b800 Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 0000:02:0d.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04) (prog-if 10 [OHCI]) Subsystem: Creative Labs SB Audigy FireWire Port Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max), cache line size 08 Interrupt: pin B routed to IRQ 11 Region 0: Memory at ec800000 (32-bit, non-prefetchable) Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ kernel BUG at kernel/timer.c:416! invalid operand: 0000 [#1] PREEMPT Modules linked in: dmx3191d snd_seq_midi snd_emu10k1_synth snd_emux_synth snd_seq_virmidi snd_seq_midi_emul snd_pcm_oss snd_mixer_oss snd_seq_oss snd_seq_midi_event snd_seq eth1394 parport_pc parport flopy ohci1294 ieee1394 snd_emu10k1 snd_rawmidi snd_seq_device snd_ac97_codec snd_pcm snd_timer snd_page_alloc snd_util_mem snd_hwdep snd nvidia e100 CPU: 0 EIP: 0060:[<c011fd68>] Tainted: P VLI EFLAGS: 00010007 (2.6.11-gentoo-r5) EIP is at cascade+0x58/0x70 eax: ddfafba8 ebx: ddfafba8 ecx: c0440208 edx: 00000026 esi: c0440338 edi: c043fa00 ebp: 00000026 esp: c0418fa0 ds: 007b es: 007b ss: 0068 Process swapper (pid :0, threadinfo=c0418000 task=c035fb20) Stack: c012739c dffce140 00000000 c043f708 c0418fcc c0418000 c012038f c043fa00 c0440208 00000026 0047b007 c0418fcc c0418fcc c0418fd8 00000001 c043f708 0000000a 0047b007 c011bdf6 c043f708 c03e3f84 00000046 00000000 c0104c71 Call Trace: [<c012739c>] queue_work+0x4c/0x80 [<c012038f>] run_timer_softirq+0x16f/0x200 [<c011bdf6>] __do_softirq+0x76/0x90 [<c0104c71>] do_softirq+0x41/0x50 ======================= [<c011bed5>] irq_exit+0x53/0x40 [<c0104b6e>] do_IRQ+0x4e/0x70 [<c01030be>] common_interrupt+01a/0x20 [<c01005d3>] default_idle+0x23/0x30 [<c0100670>] cpu_idle+0x50/0x60 [<c03e482d>] start_kernel+0x17d/0x1c0 [<c03e43a0>] unknown_bootoption+0x0/0x1e0 Code: 00 00 00 39 7b 18 89 d8 75 21 8b 1b 89 44 24 04 89 3c 24 e8 7b fb ff ff 39 f3 75 e7 89 36 89 76 04 83 c4 08 5b 5e 5f 5d c3 <0f> 0b a0 01 30 06 32 c0 eb d5 8d b4 26 00 00 00 00 8d bc 27 00 <0>Kernel panic - not syncing: Fatal exception in interrupt
Please test with vanilla-sources-2.6.12_rc2
When I apply the patch 2.6.12_rc2 on vanilla-source-2.6.11.7 (from www.kernel.org), I have a lots of errors. That is normal??
Ne prennez pas attention
Ne prennez pas attention à mon dernier post... c'est une erreur de ma part Do not take attention to my last post... it is an error
I have tested with vanilla-source-2.6.12-rc2... XSane (0.96-r1) have done a incomplete "preview" of a scan test and always hang, but after he have scanned someting with "preview" fonction. If I click "Scan" before "preview", he just stop responding. And for information, I see this in my kernel log juste after press "preview": Apr 13 23:00:28 Gentoo [<c030676d>] schedule+0x32d/0x600 Apr 13 23:00:28 Gentoo [<c03067ce>] schedule+0x38e/0x600 Apr 13 23:00:28 Gentoo [<e0bdd96e>] NCR5380_main+0x11e/0x1b0 [dmx3191d] Apr 13 23:00:28 Gentoo [<c01282bc>] worker_thread+0x1fc/0x2d0 Apr 13 23:00:28 Gentoo [<e0bdd850>] NCR5380_main+0x0/0x1b0 [dmx3191d] Apr 13 23:00:28 Gentoo [<c0113ad0>] default_wake_function+0x0/0x20 Apr 13 23:00:28 Gentoo [<c0113ad0>] default_wake_function+0x0/0x20 Apr 13 23:00:28 Gentoo [<c01280c0>] worker_thread+0x0/0x2d0 Apr 13 23:00:28 Gentoo [<c012ca5a>] kthread+0xaa/0xb0 Apr 13 23:00:28 Gentoo [<c012c9b0>] kthread+0x0/0xb0 Apr 13 23:00:28 Gentoo [<c0100ded>] kernel_thread_helper+0x5/0x18 Apr 13 23:00:29 Gentoo scheduling while atomic: events/0/0x00000001/3 Apr 13 23:00:29 Gentoo [<c0306a32>] schedule+0x5f2/0x600 Apr 13 23:00:29 Gentoo [<c01e4274>] soft_cursor+0x1b4/0x260 Apr 13 23:00:29 Gentoo [<c011470b>] sys_sched_yield+0x6b/0x90 Apr 13 23:00:29 Gentoo [<e0bdd0a8>] NCR5380_poll_politely+0xa8/0xb0 [dmx3191d] Apr 13 23:00:29 Gentoo [<e0bde07e>] NCR5380_transfer_pio+0x12e/0x200 [dmx3191d] Apr 13 23:00:29 Gentoo [<e0bde423>] NCR5380_information_transfer+0x193/0x6d0 [dmx3191d] Apr 13 23:00:29 Gentoo [<c030676d>] schedule+0x32d/0x600 Apr 13 23:00:29 Gentoo [<c03067ce>] schedule+0x38e/0x600 Apr 13 23:00:29 Gentoo [<e0bdd96e>] NCR5380_main+0x11e/0x1b0 [dmx3191d] Apr 13 23:00:29 Gentoo [<c01282bc>] worker_thread+0x1fc/0x2d0 Apr 13 23:00:29 Gentoo [<e0bdd850>] NCR5380_main+0x0/0x1b0 [dmx3191d] Apr 13 23:00:29 Gentoo [<c0113ad0>] default_wake_function+0x0/0x20 Apr 13 23:00:29 Gentoo [<c0113ad0>] default_wake_function+0x0/0x20 Apr 13 23:00:29 Gentoo [<c01280c0>] worker_thread+0x0/0x2d0 Apr 13 23:00:29 Gentoo [<c012ca5a>] kthread+0xaa/0xb0 Apr 13 23:00:29 Gentoo [<c012c9b0>] kthread+0x0/0xb0 Apr 13 23:00:29 Gentoo [<c0100ded>] kernel_thread_helper+0x5/0x18 Apr 13 23:00:30 Gentoo scheduling while atomic: events/0/0x00000001/3 Apr 13 23:00:30 Gentoo [<c0306a32>] schedule+0x5f2/0x600 Apr 13 23:00:30 Gentoo [<c01e4274>] soft_cursor+0x1b4/0x260 Apr 13 23:00:30 Gentoo [<c011470b>] sys_sched_yield+0x6b/0x90 Apr 13 23:00:30 Gentoo [<e0bdd0a8>] NCR5380_poll_politely+0xa8/0xb0 [dmx3191d] but my kernel don't make a oops
Sorry, I have this too: Apr 13 23:02:30 Gentoo scsi0 : aborting command Apr 13 23:02:30 Gentoo scsi0 : destination target 2, lun 0 Apr 13 23:02:30 Gentoo command: cdb[0]=0x28: 28 00 00 00 00 00 00 27 d8 00 Apr 13 23:02:30 Gentoo scsi0 : aborting command Apr 13 23:02:30 Gentoo scsi0 : destination target 2, lun 0 Apr 13 23:02:30 Gentoo command: cdb[0]=0x28: 28 00 00 00 00 00 00 27 d8 00 Apr 13 23:02:40 Gentoo Unable to handle kernel NULL pointer dereference at virtual address 0000014c Apr 13 23:02:40 Gentoo printing eip: Apr 13 23:02:40 Gentoo c02598f3 Apr 13 23:02:40 Gentoo *pde = 00000000 Apr 13 23:02:40 Gentoo Oops: 0000 [#1] Apr 13 23:02:40 Gentoo PREEMPT Apr 13 23:02:40 Gentoo Modules linked in: w83781d i2c_sensor snd_seq_midi snd_emu10k1_synth snd_emux_synth snd_seq_virmidi snd_seq_midi_emul snd_pcm_oss snd_mixer_oss snd_seq_oss snd_seq_midi_event snd_seq eth1394 parport_pc parport floppy ohci1394 ieee1394 snd_emu10k1 snd_rawmidi snd_seq_device snd_ac97_codec snd_pcm snd_timer snd_page_alloc snd_util_mem snd_hwdep snd dmx3191d nvidia i2c_i801 i2c_core e100 Apr 13 23:02:40 Gentoo CPU: 0 Apr 13 23:02:40 Gentoo EIP: 0060:[<c02598f3>] Tainted: P VLI Apr 13 23:02:40 Gentoo EFLAGS: 00010286 (2.6.12-rc2) Apr 13 23:02:40 Gentoo EIP is at scsi_finish_command+0x63/0xc0 Apr 13 23:02:40 Gentoo eax: 00000000 ebx: df60c400 ecx: 00000000 edx: d9fd0000 Apr 13 23:02:40 Gentoo esi: 00000000 edi: deeab1a0 ebp: df007fb4 esp: df007f6c Apr 13 23:02:40 Gentoo ds: 007b es: 007b ss: 0068 Apr 13 23:02:40 Gentoo Process scsi_eh_0 (pid: 5691, threadinfo=df007000 task=df5e65f0) Apr 13 23:02:40 Gentoo Stack: df60c400 df504000 df007fac deeab058 deeab058 df007fac c025d6bd deeab1a0 Apr 13 23:02:40 Gentoo df007fac df504038 00000286 df007fac c025d77d df007fac df007fb4 df007fac Apr 13 23:02:40 Gentoo deeab058 deeab058 df007fb4 df007fb4 df007fd8 df504000 00000000 00000000 Apr 13 23:02:40 Gentoo Call Trace: Apr 13 23:02:40 Gentoo [<c025d6bd>] scsi_eh_flush_done_q+0x7d/0xb0 Apr 13 23:02:40 Gentoo [<c025d77d>] scsi_unjam_host+0x8d/0xd0 Apr 13 23:02:40 Gentoo [<c025d85f>] scsi_error_handler+0x9f/0xd0 Apr 13 23:02:40 Gentoo [<c025d7c0>] scsi_error_handler+0x0/0xd0 Apr 13 23:02:40 Gentoo [<c0100ded>] kernel_thread_helper+0x5/0x18 Apr 13 23:02:40 Gentoo Code: e0 70 83 f8 70 74 67 0f b7 87 98 00 00 00 66 c7 47 0a 00 01 8b 57 0c 66 c7 47 08 01 10 85 d2 66 89 87 9a 00 00 00 74 10 8b 4a 70 <8b> 81 4c 01 00 00 85 c0 89 42 04 75 16 89 3c 24 ff 57 28 8b 5c
Please file a bug report for this upstream at http://bugzilla.kernel.org Please update this bug with the new bug URL.
