Sometimes when booting system just hangs and does not seem to do anything, apparently something with the serial ata drivers goes awry. Happens regardless of hibernation or regular boot but not always. Power button and new boot fixes the issue after several tries, ranging from 1 to more than a dozen tries. I have waited up to 30min to see if anything would happen but to no avail. I don't really know where the problem lies and what outputs i should add. Last lines seen on screen before hangup: Uniform Multi-Platform E-IDE driver ide: Assuming 33 MHz System bus speed for PIO mode; override with idebus=xx Driver 'sd' needs updating - please use bus_type method Driver 'sr' needs updating - please use bus_type method ACPI: PCI Interrupt 0000:00:1f.2(B) -> GSI 19 (level,low) -> IRQ 19 ata_piix 0000:00:1f.2: MAP [P0 P2 IDE IDE] ide controller lspci -v output 00:1f.2 IDE interface: Intel Corporation Mobile SATA IDE Controller (rev 03) (prog-if 80 [Master]) Subsystem: Samsung Electronics Co Ltd Device c031 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at 18e0 [size=16] I/O ports at 18d0 [size=16] Capabilities: [70] Power Management version 3 Kernel driver in use: ata_piix Happens on my samsung aura r70 deluis laptop. hard drive seems to be (according to dmesg): ata1.00: ATA-8: WDC WD3200BEVT-22ZCT0, 11.01A11, max UDMA/133 I am currently using sys-kernel/gentoo-sources-2.6.25-r7 on an amd64 no-multilib box. Reproducible: Sometimes Steps to Reproduce: 1. boot machine 2. 3. Actual Results: hangs when outputting line ata_piix 0000:00:1f.2: MAP [P0 P2 IDE IDE] Expected Results: system running after some time
Does this happen with gentoo-sources 2.6.26 or 2.6.27?
(In reply to comment #1) > Does this happen with gentoo-sources 2.6.26 or 2.6.27? > The problem existed before, than dissapeared at git-sources-2.6.26-rc6, and now appeared back at gentoo-sources-2.6.27-rc4.
(In reply to comment #2) > (In reply to comment #1) > > Does this happen with gentoo-sources 2.6.26 or 2.6.27? > > > The problem existed before, than dissapeared at git-sources-2.6.26-rc6, and now > appeared back at gentoo-sources-2.6.27-rc4. > Sorry, wrong bug
Still got the same bug using sys-kernel/gentoo-sources-2.6.26-r3.
(In reply to comment #4) > Still got the same bug using sys-kernel/gentoo-sources-2.6.26-r3. Ok. Please try the last sys-kernel/gentoo-sources-2.6.27-r4 and attach the output of smartcl -a /dev/?d?. If the bug still remains, try adding irqpoll, noacpi and noapic at the end of the boot command line. The dmesg output after a long intensive use would be great as well as a long SMART test. IMHO, this bug looks more like a disk controller dying. Did it appear after a kernel update ?
switched to sys-kernel/gentoo-sources-2.6.27-r4 and at first glance (~30 reboots) seems to fix the problem for me, will add some data after more runs. smartctl output: # smartctl -a /dev/sda smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3200BEVT-22ZCT0 Serial Number: WD-WXHZ07336286 Firmware Version: 11.01A11 User Capacity: 320.072.933.376 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Nov 26 05:14:50 2008 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 127) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 187 186 021 Pre-fail Always - 1650 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 466 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 051 Old_age Always - 0 9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1280 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 449 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 20 193 Load_Cycle_Count 0x0032 191 191 000 Old_age Always - 28185 194 Temperature_Celsius 0x0022 109 096 000 Old_age Always - 38 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 1 200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
