k3b-1.0.4 produces the error when trying to access dvdrom connected by USB. dvdrom works perfectly before starting k3b and doesn't work after. According dmesg k3b just sends some strange commands to it and it shuts down the device (/dev/sr0) Previous version k3b-0.12.17 has no such problem. Works perfectly. Before k3b start dmesg reports: ------------------------------------------------------------------------ scsi3 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 15 usb-storage: waiting for device to settle before scanning scsi 3:0:0:0: CD-ROM LITE-ON DVDRW SOHW-1213S TSD1 PQ: 0 ANSI: 0 sr0: scsi-1 drive sr 3:0:0:0: Attached scsi CD-ROM sr0 sr 3:0:0:0: Attached scsi generic sg0 type 5 usb-storage: device scan complete usb 1-5: reset high speed USB device using ehci_hcd and address 15 -------------------------------------------------------------------- After k3b start dmesg reports: -------------------------------------------------------------------- usb 1-5: device descriptor read/64, error -71 usb 1-5: device descriptor read/64, error -71 usb 1-5: reset high speed USB device using ehci_hcd and address 15 usb 1-5: device descriptor read/64, error -71 usb 1-5: device descriptor read/64, error -71 usb 1-5: reset high speed USB device using ehci_hcd and address 15 usb 1-5: device not accepting address 15, error -71 usb 1-5: reset high speed USB device using ehci_hcd and address 15 usb 1-5: device not accepting address 15, error -71 usb 1-5: USB disconnect, address 15 scsi 3:0:0:0: scsi: Device offlined - not ready after error recovery scsi 3:0:0:0: rejecting I/O to dead device scsi 3:0:0:0: rejecting I/O to dead device scsi 3:0:0:0: rejecting I/O to dead device scsi 3:0:0:0: rejecting I/O to dead device scsi 3:0:0:0: rejecting I/O to dead device scsi 3:0:0:0: rejecting I/O to dead device usb 1-5: new high speed USB device using ehci_hcd and address 16 usb 1-5: device descriptor read/64, error -71 usb 1-5: device descriptor read/64, error -71 usb 1-5: new high speed USB device using ehci_hcd and address 17 usb 1-5: device descriptor read/64, error -71 usb 1-5: device descriptor read/64, error -71 usb 1-5: new high speed USB device using ehci_hcd and address 18 usb 1-5: device not accepting address 18, error -71 usb 1-5: new high speed USB device using ehci_hcd and address 19 usb 1-5: device not accepting address 19, error -71 ------------------------------------------------------------------- k3b-1.0.4 reports when starting from console: ------------------------------------------------------------------- kbuildsycoca running... root:/home/bob# kdecore (KAction): WARNING: KActionCollection::KActionCollection ( QObject *parent, const char *name, KInstance *instance ) (K3bDevice::HalConnection) initializing HAL >= 0.5 Mapping udi /org/freedesktop/Hal/devices/storage_serial_LITE_ON_DVDRW_SOHW_1213S _222222222222_0_0 to device /dev/sr0 Mapping udi /org/freedesktop/Hal/devices/storage_model_HL_DT_STDVD_ROM_GDR8164B to device /dev/hdc /dev/hdc resolved to /dev/hdc /dev/hdc is block device (0) /dev/hdc seems to be cdrom (K3bDevice::Device) /dev/hdc: init() (K3bDevice::Device) /dev/hdc feature: DVD Read (MMC5) (K3bDevice::Device) /dev/hdc feature: DVD+R (K3bDevice::Device) /dev/hdc feature: DVD+RW (K3bDevice::ScsiCommand) failed: command: MODE SENSE (5a) errorcode: 70 sense key: ILLEGAL REQUEST (5) asc: 24 ascq: 0 (K3bDevice::Device) /dev/hdc: MODE SENSE length det failed. (K3bDevice::ScsiCommand) failed: command: MODE SENSE (5a) errorcode: 70 sense key: ILLEGAL REQUEST (5) asc: 24 ascq: 0 (K3bDevice::Device) /dev/hdc: MODE SENSE with real length 65535 failed. (K3bDevice::Device) /dev/hdc: modeSense 0x05 failed! (K3bDevice::Device) /dev/hdc: Cannot check write modes. (K3bDevice::ScsiCommand) failed: command: MODE SENSE (5a) errorcode: 70 sense key: ILLEGAL REQUEST (5) asc: 24 ascq: 0 (K3bDevice::Device) /dev/hdc: MODE SENSE length det failed. (K3bDevice::ScsiCommand) failed: command: MODE SENSE (5a) errorcode: 70 sense key: ILLEGAL REQUEST (5) asc: 24 ascq: 0 (K3bDevice::Device) /dev/hdc: MODE SENSE with real length 65535 failed. /dev/sr0 resolved to /dev/sr0 /dev/sr0 is block device (0) /dev/sr0 seems to be cdrom bus: 4, id: 0, lun: 0 (K3bDevice::Device) /dev/sr0: init() (K3bDevice::Device) /dev/sr0 feature: CD Mastering (K3bDevice::Device) /dev/sr0 feature: CD Track At Once (K3bDevice::Device) /dev/sr0 feature: DVD+R (K3bDevice::Device) /dev/sr0 feature: DVD+RW (K3bDevice::Device) /dev/sr0 feature: DVD+R Double Layer (K3bDevice::Device) /dev/sr0 feature: DVD-R/-RW Write (K3bDevice::Device) /dev/sr0 feature: Rigid Restricted Overwrite (K3bDevice::Device) /dev/sr0: dataLen: 60 (K3bDevice::Device) /dev/sr0: checking for TAO (K3bDevice::Device) /dev/sr0: checking for SAO (K3bDevice::Device) /dev/sr0: checking for SAO_R96P (K3bDevice::Device) /dev/sr0: checking for SAO_R96R (K3bDevice::Device) /dev/sr0: checking for RAW_R16 (K3bDevice::Device) /dev/sr0: checking for RAW_R96P (K3bDevice::Device) /dev/sr0: checking for RAW_R96R (K3bDevice::ScsiCommand) failed: command: GET PERFORMANCE (ac) errorcode: 0 sense key: NO SENSE (2) asc: 0 ascq: 0 (K3bDevice::Device) /dev/sr0: GET PERFORMANCE length det failed. (K3bDevice::ScsiCommand) failed: command: MODE SENSE (5a) errorcode: 0 sense key: NO SENSE (2) asc: 0 ascq: 0 (K3bDevice::Device) /dev/sr0: MODE SENSE length det failed. (K3bDevice::ScsiCommand) failed: command: MODE SENSE (5a) errorcode: 0 sense key: NO SENSE (2) asc: 0 ascq: 0 (K3bDevice::Device) /dev/sr0: MODE SENSE with real length 65535 failed. (K3bDevice::Device) could not open device /dev/sr0 for reading (No such device or address) Error while retrieving capabilities. Could not initialize device /dev/sr0 Could not resolve /dev/ide/host0/bus1/target0/lun0/cd /dev/ide/host0/bus1/target0/lun0/cd resolved to /dev/ide/host0/bus1/target0/lun0 /cd (K3bDevice::Device) could not open device /dev/ide/host0/bus1/target0/lun0/cd fo r reading (No such file or directory) could not open device /dev/ide/host0/bus1/target0/lun0/cd (No such file or direc tory) /dev/hdc resolved to /dev/hdc (K3bDevice::DeviceManager) dev /dev/hdc already found (K3bDevice::DeviceManager) found config entry for devicetype: HL-DT-ST DVD-ROM G DR8164B First sec data area: 43:41:33 (LBA 196608) (402653184 Last sec data area: 545:12:39 (LBA 2453439) (5024643072 Bytes) Last sec layer 1: 00:00:00 (LBA 0) (0 Bytes) Layer 1 length: 00:00:01 (LBA 1) (2048 Bytes) Layer 2 length: 545:12:39 (LBA 2453439) (5024643072 Bytes) (K3bDevice::Device) READ CAPACITY: 501:31:06 other capacity: 00:00:00 DiskInfo: Mediatype: DVD-ROM Current Profile: DVD-ROM Disk state: complete Empty: 0 Rewritable: 0 Appendable: 0 Sessions: 1 Tracks: 1 Layers: 1 Capacity: 501:31:07 (LBA 2256832) (4621991936 Bytes) Remaining size: 00:00:00 (LBA 0) (0 Bytes) Used Size: 501:31:07 (LBA 2256832) (4621991936 Bytes) Devices: ------------------------------ Blockdevice: /dev/hdc Generic device: Vendor: HL-DT-ST Description: DVD-ROM GDR8164B Version: 0L06 Write speed: 0 Profiles: DVD-ROM, CD-ROM Read Cap: DVD-ROM, DVD-R Dual Layer, DVD-R Dual Layer Sequential, DVD-R Du al Layer Jump, DVD+RW, DVD+R, DVD+RW Dual Layer, DVD+R Dual Layer, CD-ROM Write Cap: Error Writing modes: None Reader aliases: /dev/hdc ------------------------------ removing udi /org/freedesktop/Hal/devices/usb_device_152d_2338_222222222222_if0_ scsi_host_scsi_device_lun0_scsi_generic removing udi /org/freedesktop/Hal/devices/volume_label_NEW removing udi /org/freedesktop/Hal/devices/storage_serial_LITE_ON_DVDRW_SOHW_1213 S_222222222222_0_0 Unmapping udi /org/freedesktop/Hal/devices/storage_serial_LITE_ON_DVDRW_SOHW_121 3S_222222222222_0_0 from device /dev/sr0 removing udi /org/freedesktop/Hal/devices/usb_device_152d_2338_222222222222_if0_ scsi_host_scsi_device_lun0 removing udi /org/freedesktop/Hal/devices/usb_device_152d_2338_222222222222_if0_ scsi_host removing udi /org/freedesktop/Hal/devices/usb_device_152d_2338_222222222222_if0 removing udi /org/freedesktop/Hal/devices/usb_device_152d_2338_222222222222 kdecore (KAction): WARNING: KActionCollection::operator+=(): function is severel y deprecated. Reproducible: Always Steps to Reproduce: 1. Connect USB dvdrom 2. Start k3b (k3b-1.0.4) 3. /dev/sr0 disapearing USB dvdrom doesn't work any more root:~# emerge --info Portage 2.1.3.19 (default-linux/x86/2006.1, gcc-4.1.2, glibc-2.6.1-r0, 2.6.23-gentoo-r3 i686) ================================================================= System uname: 2.6.23-gentoo-r3 i686 AMD Athlon(tm) XP 3100+ Timestamp of tree: Sat, 19 Jan 2008 09:00:01 +0000 app-shells/bash: 3.2_p17-r1 dev-java/java-config: 1.3.7, 2.1.3 dev-lang/python: 2.3.5-r3, 2.4.4-r6 dev-python/pycrypto: 2.0.1-r6 sys-apps/baselayout: 1.12.10-r5 sys-apps/sandbox: 1.2.18.1-r2 sys-devel/autoconf: 2.13, 2.61-r1 sys-devel/automake: 1.5, 1.6.3, 1.7.9-r1, 1.8.5-r3, 1.9.6-r2, 1.10 sys-devel/binutils: 2.18-r1 sys-devel/gcc-config: 1.4.0-r4 sys-devel/libtool: 1.5.24 virtual/os-headers: 2.6.23-r3 ACCEPT_KEYWORDS="x86" CBUILD="i686-pc-linux-gnu" CFLAGS="-O3 -march=athlon-xp -pipe -fomit-frame-pointer -mfpmath=sse" CHOST="i686-pc-linux-gnu" CONFIG_PROTECT="/etc /usr/kde/3.4/env /usr/kde/3.4/share/config /usr/kde/3.4/shutdown /usr/kde/3.5/env /usr/kde/3.5/share/config /usr/kde/3.5/shutdown /usr/share/config" CONFIG_PROTECT_MASK="/etc/env.d /etc/env.d/java/ /etc/fonts/fonts.conf /etc/gconf /etc/revdep-rebuild /etc/terminfo /etc/texmf/web2c /etc/udev/rules.d" CXXFLAGS="-O3 -march=athlon-xp -pipe -fomit-frame-pointer -mfpmath=sse" DISTDIR="/usr/portage/distfiles" FEATURES="distlocks metadata-transfer sandbox sfperms strict unmerge-orphans userfetch" GENTOO_MIRRORS="http://mirror.switch.ch/mirror/gentoo/ http://distfiles.gentoo.org http://www.ibiblio.org/pub/Linux/distributions/gentoo" LANG="en_US.UTF-8" LC_ALL="en_US.UTF-8" LINGUAS="en ru de" PKGDIR="/usr/portage/packages" PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times --compress --force --whole-file --delete --delete-after --stats --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages --filter=H_**/files/digest-*" PORTAGE_TMPDIR="/var/tmp" PORTDIR="/usr/portage" PORTDIR_OVERLAY="/usr/local/portage" SYNC="rsync://rsync.gentoo.org/gentoo-portage" USE="3dnow 3dnowext X a52 aac alsa berkdb bidi bitmap-fonts cdr cli clucene cracklib crypt cups cvs dbus directfb divx4linux dri dvd dvdr dvdread encode exif faad fbcon ffmpeg fortran gdbm gif gimp gimpprint glitz gpm gtk hal icc iconv imagemagick imlib ipv6 isdnlog jack jpeg kde mad matroska midi mjpeg mmx mmxext mozilla mp3 mpeg mudflap ncurses nls nptl nptlonly nvidia ogg opengl openmp oss pam pcre pdf perl png ppds pppd python qt qt4 readline real reflection samba session slang spl sql sqlite3 sse ssl tcpd threads threadsafe tiff truetype truetype-fonts type1-fonts unicode usb v4l v4l2 vidix vim-syntax vorbis win32codecs wxwindows x264 x86 xcomposite xine xml xorg xv xvid zlib" ALSA_CARDS="intel8x0 usb-audio" ALSA_PCM_PLUGINS="adpcm alaw asym copy dmix dshare dsnoop empty extplug file hooks iec958 ioplug ladspa lfloat linear meter mulaw multi null plug rate route share shm softvol" APACHE2_MODULES="actions alias auth_basic authn_alias authn_anon authn_dbm authn_default authn_file authz_dbm authz_default authz_groupfile authz_host authz_owner authz_user autoindex cache dav dav_fs dav_lock deflate dir disk_cache env expires ext_filter file_cache filter headers include info log_config logio mem_cache mime mime_magic negotiation rewrite setenvif speling status unique_id userdir usertrack vhost_alias" ELIBC="glibc" INPUT_DEVICES="keyboard mouse evdev" KERNEL="linux" LCD_DEVICES="bayrad cfontz cfontz633 glk hd44780 lb216 lcdm001 mtxorb ncurses text" LINGUAS="en ru de" USERLAND="GNU" VIDEO_CARDS="nvidia" Unset: CPPFLAGS, CTARGET, EMERGE_DEFAULT_OPTS, INSTALL_MASK, LDFLAGS, MAKEOPTS, PORTAGE_COMPRESS, PORTAGE_COMPRESS_FLAGS, PORTAGE_RSYNC_EXTRA_OPTS
*** Bug 206715 has been marked as a duplicate of this bug. ***
Hmm. This bug is quite old. Current stable is k3b-1.0.5-r3 and kernel you tested with, 2.6.23-gentoo-r3 is also old. Burning backends have also upgraded since, cdrtools, cdrkit, dvd+rw-tools, etc. Can you give us an update from up to date system? Is this still an problem?
please test with updated k3b and kernel and reopen if you still have the problem.
