dmesg on 2.6.17-gentoo-r2

dmesg.combined (text/plain), 31.96 KB, created by Martin von Gagern on 2006-07-18 02:40:30 UTC

0000180 0000441d 00000000 00000000
[4294671.190000] Intel machine check architecture supported.
[4294671.190000] Intel machine check reporting enabled on CPU#1.
[4294671.190000] CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
[4294671.190000] CPU1: Thermal monitoring enabled
[4294671.190000] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
[4294671.247000] Total of 2 processors activated (12046.61 BogoMIPS).
[4294671.254000] ENABLING IO-APIC IRQs
[4294671.257000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[4294671.375000] checking TSC synchronization across 2 CPUs: passed.
[4294671.383000] Brought up 2 CPUs
[4294671.519000] migration_cost=2000
[4294671.523000] NET: Registered protocol family 16
[4294671.528000] ACPI: bus type pci registered
[4294671.532000] PCI: BIOS Bug: MCFG area is not E820-reserved
[4294671.537000] PCI: Not using MMCONFIG.
[4294671.542000] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
[4294671.548000] Setting up standard PCI resources
[4294671.560000] ACPI: Subsystem revision 20060127
[4294671.572000] ACPI: Interpreter enabled
[4294671.576000] ACPI: Using IOAPIC for interrupt routing
[4294671.583000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294671.588000] PCI: Probing PCI hardware (bus 00)
[4294671.590000] Boot video device is 0000:00:02.0
[4294671.591000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[4294671.598000] PCI: Transparent bridge - 0000:00:1e.0
[4294671.603000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294671.607000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[4294671.607000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[4294671.608000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[4294671.615000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[4294671.623000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[4294671.631000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[4294671.639000] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[4294671.647000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[4294671.656000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[4294671.665000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[4294671.673000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[4294671.681000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294671.686000] pnp: PnP ACPI init
[4294671.690000] pnp: ACPI device : hid PNP0A08
[4294671.690000] pnp: ACPI device : hid PNP0C01
[4294671.690000] pnp: ACPI device : hid PNP0200
[4294671.690000] pnp: ACPI device : hid PNP0B00
[4294671.690000] pnp: ACPI device : hid PNP0800
[4294671.690000] pnp: ACPI device : hid PNP0C04
[4294671.691000] pnp: ACPI device : hid PNP0700
[4294671.691000] pnp: ACPI device : hid PNP0401
[4294671.692000] pnp: ACPI device : hid PNP0C02
[4294671.692000] pnp: ACPI device : hid PNP0C02
[4294671.693000] pnp: ACPI device : hid INT0800
[4294671.693000] pnp: ACPI device : hid PNP0C02
[4294671.693000] pnp: ACPI device : hid PNP0303
[4294671.693000] pnp: ACPI device : hid PNP0F03
[4294671.694000] pnp: ACPI device : hid PNP0C02
[4294671.694000] pnp: ACPI device : hid PNP0501
[4294671.695000] pnp: ACPI device : hid PNP0C02
[4294671.695000] pnp: ACPI device : hid PNP0C02
[4294671.695000] pnp: ACPI device : hid PNP0C01
[4294671.696000] pnp: PnP ACPI: found 19 devices
[4294671.700000] PnPBIOS: Disabled by ACPI PNP
[4294671.705000] SCSI subsystem initialized
[4294671.709000] PCI: Using ACPI for IRQ routing
[4294671.713000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[4294671.740000] pnp: the driver 'system' has been registered
[4294671.740000] pnp: match found with the PnP device '00:01' and the driver 'system'
[4294671.740000] pnp: match found with the PnP device '00:08' and the driver 'system'
[4294671.740000] pnp: 00:08: ioport range 0x290-0x297 has been reserved
[4294671.746000] pnp: match found with the PnP device '00:09' and the driver 'system'
[4294671.746000] pnp: match found with the PnP device '00:0b' and the driver 'system'
[4294671.746000] pnp: match found with the PnP device '00:0e' and the driver 'system'
[4294671.746000] pnp: match found with the PnP device '00:10' and the driver 'system'
[4294671.746000] pnp: match found with the PnP device '00:11' and the driver 'system'
[4294671.746000] pnp: match found with the PnP device '00:12' and the driver 'system'
[4294671.746000] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[4294671.753000] PCI: Bridge: 0000:00:1c.0
[4294671.756000]   IO window: e000-efff
[4294671.760000]   MEM window: disabled.
[4294671.764000]   PREFETCH window: disabled.
[4294671.768000] PCI: Bridge: 0000:00:1c.1
[4294671.772000]   IO window: d000-dfff
[4294671.775000]   MEM window: bff00000-bfffffff
[4294671.780000]   PREFETCH window: disabled.
[4294671.784000] PCI: Bridge: 0000:00:1e.0
[4294671.788000]   IO window: c000-cfff
[4294671.792000]   MEM window: bfe00000-bfefffff
[4294671.796000]   PREFETCH window: dff00000-dfffffff
[4294671.801000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294671.809000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[4294671.809000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
[4294671.816000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[4294671.816000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[4294671.816000] NET: Registered protocol family 2
[4294671.832000] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[4294671.839000] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[4294671.848000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[4294671.855000] TCP: Hash tables configured (established 262144 bind 65536)
[4294671.862000] TCP reno registered
[4294671.866000] Machine check exception polling timer started.
[4294671.873000] highmem bounce pool size: 64 pages
[4294671.878000] Installing knfsd (copyright (C) 1996 [e-mail]).
[4294671.884000] Initializing Cryptographic API
[4294671.889000] io scheduler noop registered
[4294671.893000] io scheduler anticipatory registered (default)
[4294671.899000] io scheduler deadline registered
[4294671.903000] io scheduler cfq registered
[4294671.907000]  0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[4294671.907000]  0000:00:1d.0: Performing full reset
[4294671.907000]  0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[4294671.907000]  0000:00:1d.1: Performing full reset
[4294671.907000]  0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[4294671.907000]  0000:00:1d.2: Performing full reset
[4294671.907000]  0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
[4294671.907000]  0000:00:1d.3: Performing full reset
[4294671.908000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294671.915000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[4294671.915000] assign_interrupt_mode Found MSI capability
[4294671.921000] Allocate Port Service[0000:00:1c.0:pcie00]
[4294671.921000] Allocate Port Service[0000:00:1c.0:pcie02]
[4294671.921000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
[4294671.929000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[4294671.929000] assign_interrupt_mode Found MSI capability
[4294671.935000] Allocate Port Service[0000:00:1c.1:pcie00]
[4294671.935000] Allocate Port Service[0000:00:1c.1:pcie02]
[4294671.937000] Real Time Clock Driver v1.12ac
[4294671.942000] vesafb: Intel Corporation, Intel(r)915G/915GV/910GL Graphics Controller, Hardware Version 0.0 (OEM: Intel(r)915G/915GV/910GL Graphics Chip Accelerated VGA BIOS)
[4294671.957000] vesafb: VBE version: 3.0
[4294672.019000] vesafb: VBIOS/hardware doesn't support DDC transfers
[4294672.026000] vesafb: no monitor limits have been set
[4294672.031000] vesafb: scrolling: redraw
[4294672.118000] Console: switching to colour frame buffer device 128x48
[4294672.125000] vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 21600k, total 32448k
[4294672.134000] fb0: VESA VGA frame buffer device
[4294672.139000] vga16fb: initializing
[4294672.139000] vga16fb: mapped to 0xc00a0000
[4294672.143000] fb1: VGA16 VGA frame buffer device
[4294672.148000] ACPI: Processor [CPU1] (supports 8 throttling states)
[4294672.155000] isapnp: Scanning for PnP cards...
[4294672.471000] isapnp: No Plug & Play device found
[4294672.476000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[4294672.484000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.491000] pnp: the driver 'serial' has been registered
[4294672.491000] pnp: match found with the PnP device '00:0f' and the driver 'serial'
[4294672.491000] 00:0f: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294672.497000] mice: PS/2 mouse device common for all mice
[4294672.503000] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
[4294672.511000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294672.518000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294672.526000] ICH6: IDE controller at PCI slot 0000:00:1f.1
[4294672.532000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[4294672.540000] ICH6: chipset revision 3
[4294672.544000] ICH6: not 100% native mode: will probe irqs later
[4294672.555000]     ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
[4294672.567000] Probing IDE interface ide0...
[4294673.240000] hda: Pioneer DVD-ROM ATAPIModel DVD-106S 012, ATAPI CD/DVD-ROM drive
[4294673.968000] hdb: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive
[4294674.031000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294674.041000] Probing IDE interface ide1...
[4294674.555000] hda: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(66)
[4294674.566000] Uniform CD-ROM driver Revision: 3.20
[4294674.579000] hdb: ATAPI 40X CD-ROM CD-R/RW drive, 4096kB Cache, UDMA(33)
[4294674.597000] libata version 1.20 loaded.
[4294674.597000] ata_piix 0000:00:1f.2: version 1.05
[4294674.597000] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[4294674.608000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[4294674.621000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[4294674.621000] ata1: SATA max UDMA/133 cmd 0xBC00 ctl 0xB882 bmdma 0xB400 irq 19
[4294674.634000] ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xB482 bmdma 0xB408 irq 19
[4294674.903000] ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
[4294674.903000] ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
[4294674.919000] ata1: dev 0 configured for UDMA/133
[4294674.928000] scsi0 : ata_piix
[4294675.038000] ata2: SATA port has no device.
[4294675.048000] scsi1 : ata_piix
[4294675.048000]   Vendor: ATA       Model: ST3160827AS       Rev: 3.03
[4294675.048000]   Type:   Direct-Access                      ANSI SCSI revision: 05
[4294675.048000] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[4294675.048000] sda: Write Protect is off
[4294675.048000] sda: Mode Sense: 00 3a 00 00
[4294675.048000] SCSI device sda: drive cache: write back
[4294675.056000] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[4294675.056000] sda: Write Protect is off
[4294675.056000] sda: Mode Sense: 00 3a 00 00
[4294675.056000] SCSI device sda: drive cache: write back
[4294675.056000]  sda: sda1 sda2 sda3 sda4
[4294675.146000] sd 0:0:0:0: Attached scsi disk sda
[4294675.146000] pnp: the driver 'i8042 kbd' has been registered
[4294675.146000] pnp: match found with the PnP device '00:0c' and the driver 'i8042 kbd'
[4294675.146000] pnp: the driver 'i8042 aux' has been registered
[4294675.146000] pnp: match found with the PnP device '00:0d' and the driver 'i8042 aux'
[4294675.146000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[4294675.146000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294675.146000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294675.146000] EDAC MC: Ver: 2.0.0 Jul  9 2006
[4294675.150000] u32 classifier
[4294675.151000]     OLD policer on 
[4294675.151000] IPv4 over IPv4 tunneling driver
[4294675.151000] GRE over IPv4 tunneling driver
[4294675.151000] ip_conntrack version 2.4 (8192 buckets, 65536 max) - 204 bytes per conntrack
[4294675.271000] input: AT Translated Set 2 keyboard as /class/input/input0
[4294675.286000] TCP bic registered
[4294675.294000] NET: Registered protocol family 1
[4294675.303000] NET: Registered protocol family 17
[4294675.312000] p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
[4294675.324000] Starting balanced_irq
[4294675.332000] Using IPI Shortcut mode
[4294675.350000] kjournald starting.  Commit interval 5 seconds
[4294675.350000] EXT3-fs: mounted filesystem with ordered data mode.
[4294675.360000] VFS: Mounted root (ext3 filesystem) readonly.
[4294675.360000] Freeing unused kernel memory: 224k freed
[4294677.805000] ACPI: PCI Interrupt 0000:01:0b.1[A] -> GSI 22 (level, low) -> IRQ 20
[4294677.912000] Linux video capture interface: v1.00
[4294677.962000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[4294677.974000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[4294677.974000] sky2 v1.4 addr 0xbfffc000 irq 17 Yukon-EC (0xb6) rev 1
[4294677.985000] sky2 eth0: addr 00:11:2f:3b:90:fa
[4294678.004000] i8xx TCO timer: initialized (0x00000860). heartbeat=30 sec (nowayout=0)
[4294678.059000] pnp: the driver 'parport_pc' has been registered
[4294678.060000] pnp: match found with the PnP device '00:07' and the driver 'parport_pc'
[4294678.060000] parport: PnPBIOS parport detected.
[4294678.069000] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[4294678.109000] usbcore: registered new driver usbfs
[4294678.118000] usbcore: registered new driver hub
[4294678.145000] gameport: EMU10K1 is pci0000:01:0a.1/gameport0, io 0xcc00, speed 917kHz
[4294678.175000] logips2pp: Detected unknown logitech mouse model 94
[4294678.186000] uhci_hcd: Unknown symbol usb_hcd_pci_suspend
[4294678.197000] uhci_hcd: Unknown symbol usb_hcd_resume_root_hub
[4294678.208000] uhci_hcd: Unknown symbol usb_hcd_pci_probe
[4294678.218000] uhci_hcd: Unknown symbol usb_check_bandwidth
[4294678.227000] uhci_hcd: Unknown symbol usb_disabled
[4294678.237000] uhci_hcd: Unknown symbol usb_release_bandwidth
[4294678.246000] uhci_hcd: Unknown symbol usb_claim_bandwidth
[4294678.256000] uhci_hcd: Unknown symbol usb_hcd_pci_resume
[4294678.266000] uhci_hcd: Unknown symbol usb_hcd_giveback_urb
[4294678.275000] uhci_hcd: Unknown symbol usb_hcd_poll_rh_status
[4294678.285000] uhci_hcd: Unknown symbol usb_hcd_pci_remove
[4294678.295000] uhci_hcd: Unknown symbol usb_root_hub_lost_power
[4294678.312000] USB Universal Host Controller Interface driver v3.0
[4294678.323000] Linux agpgart interface v0.101 (c) Dave Jones
[4294678.323000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 21
[4294678.323000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294678.323000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[4294678.323000] drivers/usb/core/inode.c: creating file 'devices'
[4294678.323000] drivers/usb/core/inode.c: creating file '001'
[4294678.323000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[4294678.323000] uhci_hcd 0000:00:1d.0: detected 2 ports
[4294678.323000] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[4294678.323000] uhci_hcd 0000:00:1d.0: Performing full reset
[4294678.323000] uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000a880
[4294678.323000] usb usb1: default language 0x0409
[4294678.323000] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
[4294678.323000] usb usb1: Product: UHCI Host Controller
[4294678.323000] usb usb1: Manufacturer: Linux 2.6.17-gentoo-r2 uhci_hcd
[4294678.323000] usb usb1: SerialNumber: 0000:00:1d.0
[4294678.323000] usb usb1: uevent
[4294678.323000] usb usb1: configuration #1 chosen from 1 choice
[4294678.323000] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[4294678.323000] usb 1-0:1.0: uevent
[4294678.323000] hub 1-0:1.0: usb_probe_interface
[4294678.323000] hub 1-0:1.0: usb_probe_interface - got id
[4294678.323000] hub 1-0:1.0: USB hub found
[4294678.323000] hub 1-0:1.0: 2 ports detected
[4294678.323000] hub 1-0:1.0: standalone hub
[4294678.323000] hub 1-0:1.0: no power switching (usb 1.0)
[4294678.323000] hub 1-0:1.0: individual port over-current protection
[4294678.323000] hub 1-0:1.0: power on to power good time: 2ms
[4294678.323000] hub 1-0:1.0: local power source is good
[4294678.441000] drivers/usb/core/inode.c: creating file '001'
[4294678.441000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[4294678.453000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294678.453000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[4294678.462000] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
[4294678.463000] drivers/usb/core/inode.c: creating file '002'
[4294678.463000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[4294678.475000] uhci_hcd 0000:00:1d.1: detected 2 ports
[4294678.486000] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[4294678.486000] uhci_hcd 0000:00:1d.1: Performing full reset
[4294678.486000] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ac00
[4294678.497000] usb usb2: default language 0x0409
[4294678.497000] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
[4294678.497000] usb usb2: Product: UHCI Host Controller
[4294678.507000] usb usb2: Manufacturer: Linux 2.6.17-gentoo-r2 uhci_hcd
[4294678.518000] usb usb2: SerialNumber: 0000:00:1d.1
[4294678.528000] usb usb2: uevent
[4294678.528000] usb usb2: configuration #1 chosen from 1 choice
[4294678.539000] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[4294678.539000] usb 2-0:1.0: uevent
[4294678.539000] hub 2-0:1.0: usb_probe_interface
[4294678.539000] hub 2-0:1.0: usb_probe_interface - got id
[4294678.539000] hub 2-0:1.0: USB hub found
[4294678.547000] hub 2-0:1.0: 2 ports detected
[4294678.556000] hub 2-0:1.0: standalone hub
[4294678.556000] hub 2-0:1.0: no power switching (usb 1.0)
[4294678.556000] hub 2-0:1.0: individual port over-current protection
[4294678.556000] hub 2-0:1.0: power on to power good time: 2ms
[4294678.556000] hub 2-0:1.0: local power source is good
[4294678.657000] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input1
[4294678.657000] drivers/usb/core/inode.c: creating file '001'
[4294678.657000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[4294678.657000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294678.657000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[4294678.657000] drivers/usb/core/inode.c: creating file '003'
[4294678.657000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[4294678.657000] uhci_hcd 0000:00:1d.2: detected 2 ports
[4294678.657000] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[4294678.657000] uhci_hcd 0000:00:1d.2: Performing full reset
[4294678.657000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b000
[4294678.657000] usb usb3: default language 0x0409
[4294678.657000] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
[4294678.657000] usb usb3: Product: UHCI Host Controller
[4294678.657000] usb usb3: Manufacturer: Linux 2.6.17-gentoo-r2 uhci_hcd
[4294678.657000] usb usb3: SerialNumber: 0000:00:1d.2
[4294678.657000] usb usb3: uevent
[4294678.657000] usb usb3: configuration #1 chosen from 1 choice
[4294678.657000] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[4294678.657000] usb 3-0:1.0: uevent
[4294678.657000] hub 3-0:1.0: usb_probe_interface
[4294678.657000] hub 3-0:1.0: usb_probe_interface - got id
[4294678.657000] hub 3-0:1.0: USB hub found
[4294678.657000] hub 3-0:1.0: 2 ports detected
[4294678.657000] hub 3-0:1.0: standalone hub
[4294678.657000] hub 3-0:1.0: no power switching (usb 1.0)
[4294678.657000] hub 3-0:1.0: individual port over-current protection
[4294678.657000] hub 3-0:1.0: power on to power good time: 2ms
[4294678.657000] hub 3-0:1.0: local power source is good
[4294678.779000] ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
[4294678.779000] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
[4294678.779000] uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00
[4294678.779000] hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[4294678.780000] drivers/usb/core/inode.c: creating file '001'
[4294678.780000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 21
[4294678.792000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294678.792000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[4294678.802000] drivers/usb/core/inode.c: creating file '004'
[4294678.802000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[4294678.815000] ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8
[4294678.815000] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
[4294678.815000] ehci_hcd 0000:00:1d.7: debug port 1
[4294678.824000] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[4294678.824000] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[4294678.824000] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xbfdff800
[4294678.835000] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
[4294678.839000] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
[4294678.839000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[4294678.851000] usb usb4: default language 0x0409
[4294678.851000] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
[4294678.851000] usb usb4: Product: EHCI Host Controller
[4294678.858000] uhci_hcd 0000:00:1d.1: port 1 portsc 0082,00
[4294678.861000] usb usb4: Manufacturer: Linux 2.6.17-gentoo-r2 ehci_hcd
[4294678.872000] usb usb4: SerialNumber: 0000:00:1d.7
[4294678.881000] usb usb4: uevent
[4294678.881000] usb usb4: configuration #1 chosen from 1 choice
[4294678.891000] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[4294678.891000] usb 4-0:1.0: uevent
[4294678.891000] hub 4-0:1.0: usb_probe_interface
[4294678.891000] hub 4-0:1.0: usb_probe_interface - got id
[4294678.891000] hub 4-0:1.0: USB hub found
[4294678.899000] hub 4-0:1.0: 8 ports detected
[4294678.908000] hub 4-0:1.0: standalone hub
[4294678.908000] hub 4-0:1.0: no power switching (usb 1.0)
[4294678.908000] hub 4-0:1.0: individual port over-current protection
[4294678.908000] hub 4-0:1.0: Single TT
[4294678.908000] hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns)
[4294678.908000] hub 4-0:1.0: power on to power good time: 20ms
[4294678.908000] hub 4-0:1.0: local power source is good
[4294678.963000] hub 2-0:1.0: debounce: port 1: total 175ms stable 100ms status 0x100
[4294678.963000] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
[4294679.009000] hub 4-0:1.0: state 7 ports 8 chg 0000 evt 0000
[4294679.009000] drivers/usb/core/inode.c: creating file '001'
[4294679.009000] ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
[4294679.009000] hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
[4294679.010000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294679.022000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[4294679.050000] CAPI Subsystem Rev 1.1.2.8
[4294679.113000] hub 4-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
[4294679.164000] ehci_hcd 0000:00:1d.7: port 3 full speed --> companion
[4294679.164000] ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
[4294679.182000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[4294679.194000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[4294679.194000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[4294679.205000] drivers/usb/core/inode.c: creating file '005'
[4294679.205000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[4294679.218000] uhci_hcd 0000:00:1d.3: detected 2 ports
[4294679.227000] uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000
[4294679.227000] uhci_hcd 0000:00:1d.3: Performing full reset
[4294679.227000] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000b080
[4294679.238000] usb usb5: default language 0x0409
[4294679.238000] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
[4294679.238000] usb usb5: Product: UHCI Host Controller
[4294679.248000] usb usb5: Manufacturer: Linux 2.6.17-gentoo-r2 uhci_hcd
[4294679.259000] usb usb5: SerialNumber: 0000:00:1d.3
[4294679.268000] usb usb5: uevent
[4294679.268000] usb usb5: configuration #1 chosen from 1 choice
[4294679.278000] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[4294679.278000] usb 5-0:1.0: uevent
[4294679.278000] hub 5-0:1.0: usb_probe_interface
[4294679.278000] hub 5-0:1.0: usb_probe_interface - got id
[4294679.278000] hub 5-0:1.0: USB hub found
[4294679.286000] hub 5-0:1.0: 2 ports detected
[4294679.294000] hub 5-0:1.0: standalone hub
[4294679.294000] hub 5-0:1.0: no power switching (usb 1.0)
[4294679.294000] hub 5-0:1.0: individual port over-current protection
[4294679.294000] hub 5-0:1.0: power on to power good time: 2ms
[4294679.294000] hub 5-0:1.0: local power source is good
[4294679.295000] bttv: driver version 0.9.16 loaded
[4294679.304000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[4294679.347000] fcpci: module license 'Proprietary' taints kernel.
[4294679.395000] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[4294679.395000] drivers/usb/core/inode.c: creating file '001'
[4294679.395000] ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 22
[4294679.459000] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0002
[4294679.459000] uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00
[4294679.459000] hub 2-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
[4294679.460000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]  MMIO=[bfeff000-bfeff7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[4294679.482000] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 22
[4294679.511000] bttv: Bt8xx card found (0).
[4294679.521000] ACPI: PCI Interrupt 0000:01:0b.0[A] -> <6>agpgart: Detected an Intel 915G Chipset.
[4294679.534000] GSI 22 (level, low) -> IRQ 20
[4294679.534000] agpgart: Detected 32508K stolen memory.
[4294679.546000] uhci_hcd 0000:00:1d.0: suspend_rh (auto-stop)
[4294679.558000] bttv0: Bt878 (rev 17) at 0000:01:0b.0, <6>agpgart: AGP aperture is 256M @ 0xc0000000
[4294679.572000] irq: 20, latency: 64, mmio: 0xdfffe000
[4294679.582000] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
[4294679.595000] bttv0: using: Hauppauge (bt878) [card=10,insmod option]
[4294679.595000] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[4294679.606000] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
[4294679.609000] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
[4294679.697000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[4294679.711000] tveeprom 0-0050: Hauppauge model 44354, rev B121, serial# 2154770
[4294679.723000] tveeprom 0-0050: tuner model is Philips FM1216 (idx 21, type 5)
[4294679.736000] tveeprom 0-0050: TV standards PAL(B/G) (eeprom 0x04)
[4294679.747000] tveeprom 0-0050: audio processor is MSP3415 (idx 6)
[4294679.758000] tveeprom 0-0050: has radio
[4294679.767000] bttv0: Hauppauge eeprom indicates model#44354
[4294679.778000] bttv0: using tuner=1
[4294679.786000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[4294679.798000] fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2
[4294679.798000] uhci_hcd 0000:00:1d.2: suspend_rh (auto-stop)
[4294679.810000] fcpci: (fcpci built on Jul  9 2006 at 12:19:46)
[4294679.822000] fcpci: -- 32 bit CAPI driver --
[4294679.853000] msp3400 0-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
[4294679.859000] usb 2-1: ep0 maxpacket = 32
[4294679.865000] msp3400 0-0040: MSP3415D-B3 supports nicam, mode is autodetect
[4294679.872000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[4294679.872000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[4294679.907000] usb 2-1: skipped 4 descriptors after interface
[4294679.917000] usb 2-1: skipped 3 descriptors after interface
[4294679.920000] bttv0: i2c: checking for TDA9887 @ 0x86... <7>usb 2-1: default language 0x0409
[4294679.936000] not found
[4294679.938000] usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3
[4294679.938000] usb 2-1: Product: USB Network Interface
[4294679.938000] usb 2-1: Manufacturer: Speedtouch
[4294679.938000] usb 2-1: SerialNumber: 000e50add163
[4294679.938000] usb 2-1: uevent
[4294679.938000] usb 2-1: configuration #2 chosen from 2 choices
[4294679.944000] usb 2-1: adding 2-1:2.0 (config #2, interface 0)
[4294679.944000] usb 2-1:2.0: uevent
[4294679.946000] usb 2-1: adding 2-1:2.1 (config #2, interface 1)
[4294679.946000] usb 2-1:2.1: uevent
[4294679.948000] drivers/usb/core/inode.c: creating file '002'
[4294680.057000] tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
[4294680.068000] tuner 0-0061: type set to 1 (Philips PAL_I (FI1246 and compatibles))
[4294680.113000] bttv0: registered device video0
[4294680.124000] bttv0: registered device vbi0
[4294680.134000] bttv0: registered device radio0
[4294680.179000] bttv0: PLL: 28636363 => 35468950 .. ok
[4294680.233000] ACPI: PCI Interrupt 0000:01:09.0[A] -> GSI 17 (level, low) -> IRQ 17
[4294680.246000] fcpci: AVM FRITZ!Card PCI found: port 0xc800, irq 17
[4294680.257000] fcpci: Loading...
[4294680.266000] fcpci: Driver 'fcpci' attached to fcpci-stack. (152)
[4294680.401000] uhci_hcd 0000:00:1d.3: suspend_rh (auto-stop)
[4294680.498000] fcpci: Stack version 3.11-07
[4294680.506000] kcapi: Controller 1: fcpci-c800-17 attached
[4294680.516000] kcapi: card 1 "fcpci-c800-17" ready.
[4294680.525000] fcpci: Loaded.
[4294680.753000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e018000087dca6]
[4294681.160000] ts: Compaq touchscreen protocol output
[4294683.781000] cdc_ether 2-1:2.0: usb_probe_interface
[4294683.781000] cdc_ether 2-1:2.0: usb_probe_interface - got id
[4294684.238000] cdc_ether 2-1:2.0: status ep5in, 8 bytes period 64
[4294684.238000] eth1: register 'cdc_ether' at usb-0000:00:1d.1-1, CDC Ethernet Device, 00:0e:50:ad:d1:63
[4294684.252000] usbcore: registered new driver cdc_ether
[4294685.255000] EXT3 FS on sda1, internal journal
[4294685.498000] input: PC Speaker as /class/input/input2
[4294685.621000] loop: loaded (max 8 devices)
[4294685.653000] CSLIP: code copyright 1989 Regents of the University of California
[4294685.663000] PPP generic driver version 2.4.2
[4294685.720000] lirc_dev: IR Remote Control driver registered, at major 61 
[4294685.754000] lirc_i2c: chip found @ 0x18 (Hauppauge IR)
[4294685.754000] lirc_dev: lirc_register_plugin: sample_rate: 10
[4294685.931000] kjournald starting.  Commit interval 5 seconds
[4294685.931000] EXT3 FS on sda2, internal journal
[4294685.931000] EXT3-fs: mounted filesystem with ordered data mode.
[4294686.040000] Adding 1927792k swap on /dev/sda3.  Priority:-1 extents:1 across:1927792k
[4294699.225000] ip_tables: (C) 2000-2006 Netfilter Core Team
[4294700.160000] sky2 eth0: enabling interface
[4294701.847000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[4294703.940000] NET: Registered protocol family 24
[4294703.954000] eth1: rxqlen 0 --> 4
[4294704.123000] NET: Registered protocol family 10
[4294704.123000] lo: Disabled Privacy Extensions
[4294704.123000] IPv6 over IPv4 tunneling driver
[4294713.858000] capifs: Rev 1.1.2.3
[4294713.929000] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
[4294714.262000] eth0: no IPv6 routers present
[4294714.929000] eth1: no IPv6 routers present
[4294723.911000] tun: Universal TUN/TAP device driver, 1.6
[4294723.911000] tun: (C) 1999-2004 Max Krasnyansky <[e-mail]>
[4474438.378000] capilib_new_ncci: kcapi: appl 1 ncci 0x10101 up
[4474559.391000] kcapi: appl 1 ncci 0x10101 down
[4543494.607000] [drm] Initialized drm 1.0.1 20051102
[4543494.609000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[4543494.610000] [drm] Initialized i915 1.4.0 20060119 on minor 0
[4543762.783000] logips2pp: Detected unknown logitech mouse model 94
[4546060.653000] logips2pp: Detected unknown logitech mouse model 94
[4546897.426000] logips2pp: Detected unknown logitech mouse model 94
[4547264.246000] logips2pp: Detected unknown logitech mouse model 94
[4557839.884000] logips2pp: Detected unknown logitech mouse model 94