dmesg output of a succesful load after warm start from windows with kernel 2.6.16

dmesg.2.6.16-good (text/plain), 13.08 KB, created by Sebastian Volke on 2006-03-25 06:33:33 UTC

Bootdata ok (command line is root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda1 udev vga=795)
Linux version 2.6.16-gentoo (root@gentoo) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #1 PREEMPT Sat Mar 25 14:39:52 CET 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001ffb0000 (usable)
 BIOS-e820: 000000001ffb0000 - 000000001ffc0000 (ACPI data)
 BIOS-e820: 000000001ffc0000 - 000000001fff0000 (ACPI NVS)
 BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 ACPIAM                                ) @ 0x00000000000f8da0
ACPI: RSDT (v001 A M I  OEMRSDT  0x09000526 MSFT 0x00000097) @ 0x000000001ffb0000
ACPI: FADT (v002 A M I  OEMFACP  0x09000526 MSFT 0x00000097) @ 0x000000001ffb0200
ACPI: MADT (v001 A M I  OEMAPIC  0x09000526 MSFT 0x00000097) @ 0x000000001ffb0390
ACPI: OEMB (v001 A M I  AMI_OEM  0x09000526 MSFT 0x00000097) @ 0x000000001ffc0040
ACPI: DSDT (v001  K8UNF K8UNF121 0x00000121 INTL 0x02002026) @ 0x0000000000000000
No mptable found.
On node 0 totalpages: 127988
  DMA zone: 2826 pages, LIFO batch:0
  DMA32 zone: 125162 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda1 udev vga=795
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 1808.813 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Memory: 509188k/523968k available (2846k kernel code, 13952k reserved, 1056k data, 208k init)
Calibrating delay using timer specific routine.. 3621.57 BogoMIPS (lpj=7243153)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU: AMD Sempron(tm) Processor 3000+ stepping 02
Using local APIC timer interrupts.
result 12561210
Detected 12.561 MHz APIC timer.
testing NMI watchdog ... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1459k freed
DMI 2.3 present.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *3
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 22) *14
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to [e-mail] cc [e-mail])
pnp: 00:0d: ioport range 0x290-0x29f has been reserved
PCI: Bridge: 0000:00:0b.0
  IO window: a000-cfff
  MEM window: ff400000-ff4fffff
  PREFETCH window: 9eb00000-deafffff
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: ff500000-ff5fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:0e.0 to 64
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
fuse init (API version 7.6)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
sc520_wdt: WDT driver for SC520 initialised. timeout=30 sec (nowayout=0)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 256M @ 0xe0000000
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000180000, using 7680k, total 16384k
vesafb: mode is 1280x1024x24, linelength=3840, pages=3
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
input: PC Speaker as /class/input/input2
isa bounce pool size: 16 pages
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST3160021A, ATA DISK drive
hdb: Maxtor 6Y080P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
hdb: max request size: 128KiB
hdb: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
 hdb: hdb1 hdb2 hdb3
hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
SCSI Media Changer driver v0.25 
usbmon: debugfs is not available
usbcore: registered new driver libusual
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04 08:57:20 2006 UTC).
ALSA device list:
  No soundcards found.
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
Losing some ticks... checking if CPU frequency changed.
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.0)
powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    1 : fid 0x2 (1000 MHz), vid 0xa (1300 mV)
cpu_init done, current fid 0xa, vid 0x6
ACPI wakeup devices: 
PS2K PS2M UAR1 USB0  MAC AC97 USB1 USB2 P0P1 
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Freeing unused kernel memory: 208k freed
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 22 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 0
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 16, io mem 0xff6fdc00
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.3
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 17, io mem 0xff6ff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 20 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 18, io mem 0xff6fe000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
libata version 1.20 loaded.
sata_nv 0000:00:0a.0: version 0.8
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 22 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata1: SATA max UDMA/133 cmd 0xF80 ctl 0xF02 bmdma 0xD800 irq 16
ata2: SATA max UDMA/133 cmd 0xE80 ctl 0xE02 bmdma 0xD808 irq 16
ata1: SATA link down (SStatus 0)
scsi0 : sata_nv
ata2: SATA link down (SStatus 0)
scsi1 : sata_nv
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
Adding 1951888k swap on /dev/hdb2.  Priority:-1 extents:1 across:1951888k
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5040
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
parport0: Printer, HEWLETT-PACKARD DESKJET 690C