Linux version 2.6.14-gentoo-r5 (root@localhost) (gcc version 3.3.6 (Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #1 SMP PREEMPT Mon Dec 26 16:24:29 SAST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 00000000000da014 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data) BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000fc0f0 On node 0 totalpages: 262128 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 32752 pages, LIFO batch:15 DMI 2.3 present. ACPI: RSDP (v000 AMI ) @ 0x000fa3a0 ACPI: RSDT (v001 AMIINT INTEL865 0x00000010 MSFT 0x00000097) @ 0x3fff0000 ACPI: FADT (v001 AMIINT INTEL865 0x00000011 MSFT 0x00000097) @ 0x3fff0030 ACPI: MADT (v001 AMIINT INTEL865 0x00000009 MSFT 0x00000097) @ 0x3fff00c0 ACPI: DSDT (v001 INTEL I865G 0x00001000 MSFT 0x0100000d) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:2 APIC version 20 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) Built 1 zonelists Kernel command line: mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 3245.761 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1033560k/1048512k available (3410k kernel code, 14116k reserved, 1049k data, 248k init, 131008k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 6499.82 BogoMIPS (lpj=12999651) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 09 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 6491.39 BogoMIPS (lpj=12982790) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 09 Total of 2 processors activated (12991.22 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 pin1=2 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=2 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0400-043f claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT] ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: f3d00000-f7dfffff PREFETCH window: d3c00000-f3bfffff PCI: Bridge: 0000:00:1e.0 IO window: b000-bfff MEM window: f7e00000-f7efffff PREFETCH window: 50000000-500fffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 Machine check exception polling timer started. apm: BIOS not found. audit: initializing netlink socket (disabled) audit(1139515016.528:1): initialized highmem bounce pool size: 64 pages Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.24 [Flags: R/O]. lp: driver loaded but no devices found Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 865 Chipset. agpgart: AGP aperture is 64M @ 0xf8000000 vesafb: Leadtek Research Inc., nv40 Board - 20172996, Chip Rev (OEM: WinFast) vesafb: VBE version: 3.0 vesafb: VBIOS/hardware supports DDC2 transfers vesafb: monitor limits: vf = 85 Hz, hf = 82 kHz, clk = 140 MHz vesafb: scrolling: redraw Console: switching to colour frame buffer device 128x48 vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 10240k, total 262144k fb0: VESA VGA frame buffer device ACPI: CPU0 (power states: C1[C1]) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: CPU1 (power states: C1[C1]) ACPI: Processor [CPU2] (supports 8 throttling states) PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS2 at I/O 0x3e8 (irq = 0) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)] lp0: using parport0 (interrupt-driven). mice: PS/2 mouse device common for all mice io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered r8169 Gigabit Ethernet driver 2.2LK loaded ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 20 (level, low) -> IRQ 16 eth0: Identified chip type is 'RTL8169s/8110s'. eth0: RTL8169 at 0xf880ef00, 00:0c:76:96:7e:5c, IRQ 16 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... input: AT Translated Set 2 keyboard on isa0060/serio0 hda: ST3120026A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: AOpen Inc. DVD-ROM DVD-1648/PMP 0108, ATAPI CD/DVD-ROM drive hdd: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 1024KiB hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 > hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) libata version 1.12 loaded. ata_piix version 1.04 ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 17 ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 17 ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f ata1: dev 0 ATA, max UDMA/133, 390721968 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi0 : ata_piix ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:207f ata2: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48 ata2: dev 0 configured for UDMA/133 scsi1 : ata_piix Vendor: ATA Model: ST3200822AS Rev: 3.01 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: ST3250823AS Rev: 3.03 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) SCSI device sda: drive cache: write back SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 > Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0 ieee1394: raw1394: /dev/raw1394 device initialized ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: irq 18, io mem 0xf7fff800 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000cc00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000d000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000d400 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000d800 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 2-2: new low speed USB device using uhci_hcd and address 2 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. input: USB HID v1.11 Mouse [Microsoft Microsoft USB Wireless Mouse] on usb-0000:00:1d.0-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC). ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 17 ALSA device list: #0: SBLive! Value [CT4832] (rev.6, serial:0x80271102) at 0xb800, irq 17 oprofile: using NMI interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered ip_conntrack version 2.3 (8191 buckets, 65528 max) - 216 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode ReiserFS: hda5: found reiserfs format "3.6" with standard journal ReiserFS: hda5: using ordered data mode ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda5: checking transaction log (hda5) ReiserFS: hda5: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 248k freed Adding 2096472k swap on /dev/hda3. Priority:-1 extents:1 across:2096472k NTFS volume version 3.1. ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal EXT3-fs: mounted filesystem with ordered data mode. ReiserFS: sdb3: found reiserfs format "3.6" with standard journal ReiserFS: sdb3: using ordered data mode ReiserFS: sdb3: journal params: device sdb3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sdb3: checking transaction log (sdb3) ReiserFS: sdb3: Using r5 hash to sort names r8169: eth0: link up nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:22:51 PST 2005 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A atkbd.c: Unknown key pressed (translated set 2, code 0xbf on isa0060/serio0). atkbd.c: Use 'setkeycodes e03f ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xbf on isa0060/serio0). atkbd.c: Use 'setkeycodes e03f ' to make it known.