GNU Mach 1.3 AT386 boot: physical memory from 0x0 to 0x20100000 GNU Mach 1.3 AT386 boot: physical memory from 0x0 to 0x20100000 pcibios_init : BIOS32 Service Directory structure at 0xp pcibios_init : BIOS32 Service Directory entry at 0xfdb10 pcibios_init : PCI BIOS revision 2.10 entry at 0xfdb31 Probing PCI hardware. ide: SiS 5513 (dual FIFO) DMA Bus Mastering IDE Controller on PCI bus 0 function 21 ide0: BM-DMA at 0xff00-0xff07 ide1: BM-DMA at 0xff08-0xff0f hd0: Maxtor 2F040L0, 39205MB w/2048kB Cache, CHS=4998/255/63 hd1: WDC WD2000JB-00GVA0, 131071MB w/8192kB Cache, CHS=16709/255/63 hd2: _NEC DV-5700B, ATAPI CDROM drive hd3: R/RW 12x8x32, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Failed initialization of WD-7000 SCSI card! EATA0: address 0x1f0 in use, skipping probe. EATA0: address 0x170 in use, skipping probe. ppa: Version 1.42 ppa: Probing port 03bc ppa: Probing port 0378 ppa: SPP port present ppa: ECP with a i byte FIFO present ppa: PS/2 bidirectional port present ppa: Passed Intel bug check. ppa: EPP 1.9 with hardware direction protocol ppa: Probing port 0278 scsi : 0 hosts. scsi : detected total. rtl8139.c:v1.23a 8/24/2003 Donald Becker, becker@scyld.com. http://www.scyld.com/network/rtl8139.html sis900.c: modified v1.06.11 4/30/2002 eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 11, 0: b:6a:5f:39:ec. eth0: Realtek RTL8201 PHY transceiver found at address 1. eth0: Using transceiver found at address 1 as default via-rhine.c:v1.16 7/22/2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html 0 3c515 cards found. RV(^f-}: wavelan_probe(): invalid base address RV(^f-}: D-Link DE-600 pocket adapter: not at I/O 0x378. D-Link DE-620 pocket adapter not identified in the printer port Partition check (DOS partitions): hd0: hd0s1 hd0s2 hd0s3 hd1: hd1s1 hd1s2 hd1s3 hd1s4 com0: at atbus0, port = 3f8, spl = 6, pic = 4. (DOS COM1) module 0: /hurd/ext2fs.static --multiboot-command-line=${kernel-command-line} --host-priv-port=${host-port} --device-master-port=${device-port} --exec-server-task=${exec-task} -T typed ${root} $(task-create) $(task-resume) module 1: /lib/ld.so.1 /hurd/exec $(exec-task=task-create) 2 multiboot modules task loaded: /hurd/ext2fs.static --multiboot-command-line=/boot/gnumach-dbg.gz root=device:hd0s1 --host-priv-port=2 --device-master-port=3 --exec-server-task=4 -T typed device:hd0s1 task loaded: /lib/ld.so.1 /hurd/exec start /hurd/ext2fs.static: eth0: Media Link On 100mbps full-duplex