n: 02 Vendor: TOSHIBA Model: DVD-ROM SD-M1401 Rev: 1008 Type: CD-ROM ANSI SCSI revision: 02 Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.03 Type: CD-ROM ANSI SCSI revision: 02 Vendor: IOMEGA Model: ZIP 100 Rev: J.03 Type: Direct-Access ANSI SCSI revision: 02 Vendor: IBM Model: DDYS-T36950N Rev: S96H Type: Direct-Access ANSI SCSI revision: 03 ncr53c895-0-<0,0>: tagged command queue depth set to 4 ncr53c895-0-<1,0>: tagged command queue depth set to 4 ncr53c895-0-<8,0>: tagged command queue depth set to 4 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0 Attached scsi CD-ROM sr1 at scsi0, channel 0, id 3, lun 0 Attached scsi CD-ROM sr2 at scsi0, channel 0, id 4, lun 0 ncr53c895-0-<2,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8) sr0: scsi3-mmc drive: 12x/12x writer cd/rw xa/form2 cdda caddy Uniform CD-ROM driver Revision: 3.12 ncr53c895-0-<3,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 16) sr1: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray ncr53c895-0-<4,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 15) sr2: scsi-1 drive NCR53c406a: no available ports found aec671x_detect: PCI: Found IRQ 9 for device 02:0c.0 PCI: Sharing IRQ 9 with 02:0b.1 scsi: Detection failed (no card) GDT: Storage RAID Controller Driver. Version: 2.05 GDT: Found 0 PCI Storage RAID Controllers megaraid: v1.18k (Release Date: Thu Aug 28 10:05:11 EDT 2003) megaraid: no BIOS enabled. DC390: 0 adapters found Failed initialization of WD-7000 SCSI card! Fusion MPT base driver 2.05.16 Copyright (c) 1999-2004 LSI Logic Corporation mptbase: 0 MPT adapters found, 0 installed. Compaq SMART2 Driver (v 2.4.28) cdrom: open failed. cdrom: open failed. ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A cloop: Initializing cloop v1.02 cloop: /newroot/mnt/cdrom/sysrcd.dat: 2161 blocks, 131072 bytes/block, largest block is 131118 bytes. cloop: loaded (max 8 devices) usb.c: registered new driver usbdevfs usb.c: registered new driver hub 3c505.c: warning, using default DMA channel, 3c505.c: module autoprobe not recommended, give io=xx. 3c505.c: Failed to register card at 0x0. 3c507: register_netdev() returned non-zero. 3c515.c:v0.99t 17-Nov-2001 becker@scyld.com and others 0 3c515 cards found. 3c523.c: No 3c523 cards found PCI: Enabling device 02:0a.0 (0014 -> 0017) PCI: Assigned IRQ 5 for device 02:0a.0 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html See Documentation/networking/vortex.txt 02:0a.0: 3Com PCI 3c905C Tornado at 0xd800. Vers LK1.1.18-ac 00:01:02:b0:23:cc, IRQ 5 product code 4552 rev 00.13 date 08-12-00 Internal config register is 2000000, transceivers 0xa. 8K byte-wide RAM 5:3 Rx:Tx split, 10baseT interface. Enabling bus-master transmits and whole-frame receives. 02:0a.0: scatter/gather enabled. h/w checksums enabled ac3200.c: No ac3200 card found (i/o = 0x0). aironet4500_cards.c v0.2 Feb 27, 2000 Elmer Joandi, elmer@ylenurme.ee. <3>No Aironet 4X00 cards were found. Note that for ISA cards you should use either automatic PNP mode or ISA mode with both io and irq param Aironet is also afraid of: being second PNP controller(by slot), having anything(brandname bios weirdnesses) in range 0x100-0x180 and maybe around 0xd0000 If you PNP type card does not get found, try non-PNP switch before complainig. aironet4500.c v0.1 1/1/99 Elmer Joandi, elmer@ylenurme.ee. arlan: no devices found at1700: register_netdev() returned non-zero. atp.c:v1.09 8/9/2000 Donald Becker http://www.scyld.com/network/atp.html cs89x0.c: Module autoprobing not allowed. cs89x0.c: Append io=0xNNN eth1: D-Link DE-600 pocket adapter: not at I/O 0x378. D-Link DE-620 pocket adapter not identified in the printer port defxx.c:v1.05e 2001/02/03 Lawrence V. Stefani and others eth1: depca_probe() cannot find device at 0x0200. dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $ FW=Build 550 11/16/96 03:45:15 FW Version=$Version$ dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17) Intel(R) PRO/1000 Network Driver - version 5.2.30.1 Copyright (c) 1999-2004 Intel Corporation. e2100.c: Presently autoprobing (not recommended) for a single card. e2100.c: No E2100 card found (i/o = 0x0). eepro_init_module: Probe is very dangerous in ISA boards! eepro_init_module: Please add "autodetect=1" to force probe eexpress.c: Module autoprobe not recommended, give io=xx. eexpress.c: Failed to register card at 0x0. eth16i.c: Presently autoprobing (not recommended) for a single card. eth16i.c No Eth16i card found (i/o = 0x0). eth1: ewrk3_probe() cannot find device at 0x0300. hp-plus.c: Presently autoprobing (not recommended) for a single card. hp-plus.c: No HP-Plus card found (i/o = 0x0). hp.c: Presently autoprobing (not recommended) for a single card. hp.c: No HP card found (i/o = 0x0). lance.c: Module autoprobing not allowed. Append "io=0xNNN" value(s). eth1: i82596 initialization timed out natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002 originally by Donald Becker http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder ne2.c: No NE/2 card found. ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker http://www.scyld.com/network/ne2k-pci.html NI5010: Autoprobing for modules is hazardous, trying anyway.. ni52: Autoprobing not allowed for modules. ni52: Set symbols 'io' 'irq' 'memstart' and 'memend' ns83820.c: National Semiconductor DP83820 10/100/1000 driver. pcnet32.c:v1.30c 05.25.2004 tsbogend@alpha.franken.de sis900.c: v1.08.07 11/02/2003 SLIP: version 0.8.4-NET3.019-NEWTTY-MODULAR (dynamic channels, max=256). smc-mca.c: No SMC Ultra card found (i/o = 0x0). SMC9194: You shouldn't use auto-probing with insmod! starfire.c:v1.03 7/26/2000 Written by Donald Becker (unofficial 2.2/2.4 kernel port, version 1.03+LK1.3.9, December 13, 2002) STRIP: Version 1.3-STUART.CHESHIRE-MODULAR (unlimited channels) sundance.c:v1.01+LK1.09a 10-Jul-2003 Written by Donald Becker http://www.scyld.com/network/sundance.html ThunderLAN driver v1.15 TLAN: 0 devices installed, PCI: 0 EISA: 0 Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html WaveLAN init_module(): doing device probing (bad !) Specify base addresses while loading module to correct the problem WaveLAN init_module(): no device found wd.c: Presently autoprobing (not recommended) for a single card. wd.c: No wd80x3 card found (i/o = 0x0). winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker http://www.scyld.com/network/drivers.html yellowfin.c:v1.05 1/09/2001 Written by Donald Becker http://www.scyld.com/network/yellowfin.html (unofficial 2.4.x port, 1.05+LK1.1.5, May 10, 2001) eth0: no IPv6 routers present parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected parport0: Printer, Brother HL-5130 series Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 Attached scsi removable disk sdc at scsi0, channel 0, id 5, lun 0 Attached scsi disk sdd at scsi0, channel 0, id 8, lun 0 ncr53c895-0-<0,*>: FAST-20 SCSI 20.0 MB/s (50 ns, offset 31) SCSI device sda: 35843670 512-byte hdwr sectors (18352 MB) /dev/scsi/host0/bus0/target0/lun0:<7>ldm_validate_partition_table(): Found an MS-DOS partition table, not a dynamic disk. p1 p2 ncr53c895-0-<1,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 15) SCSI device sdb: 8925000 512-byte hdwr sectors (4570 MB) /dev/scsi/host0/bus0/target1/lun0:<7>ldm_validate_partition_table(): Found an MS-DOS partition table, not a dynamic disk. p1 p2 ncr53c895-0-<5,*>: target did not report SYNC. sdc: Unit Not Ready, sense: Current 00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x11 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 0xff 0xfe 0x01 0x00 0x00 0x00 0x00 sdc : READ CAPACITY failed. sdc : status = 1, message = 00, host = 0, driver = 28 Current sd00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x11 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 0xff 0xfe 0x01 0x00 0x00 0x00 0x00 sdc : block size assumed to be 512 bytes, disk size 1GB. /dev/scsi/host0/bus0/target5/lun0: I/O error: dev 08:20, sector 0 I/O error: dev 08:20, sector 0 unable to read partition table ncr53c895-0-<8,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns, offset 31) SCSI device sdd: 71687340 512-byte hdwr sectors (36704 MB) /dev/scsi/host0/bus0/target8/lun0:<7>ldm_validate_partition_table(): Found an MS-DOS partition table, not a dynamic disk. p1 < p5 > sdc: Unit Not Ready, sense: Current 00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x11 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 0xff 0xfe 0x01 0x00 0x00 0x00 0x00 sdc : READ CAPACITY failed. sdc : status = 1, message = 00, host = 0, driver = 28 Current sd00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x11 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 0xff 0xfe 0x01 0x00 0x00 0x00 0x00 sdc : block size assumed to be 512 bytes, disk size 1GB. sdc: Write Protect is off /dev/scsi/host0/bus0/target5/lun0: I/O error: dev 08:20, sector 0 I/O error: dev 08:20, sector 0 unable to read partition table Device not ready. Make sure there is a disc in the drive. inserting floppy driver for 2.4.27-fd36 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 i810_rng: cannot register misc device PCI: Found IRQ 9 for device 02:0c.0 PCI: Sharing IRQ 9 with 02:0b.1 sym53c8xx: at PCI bus 2, device 12, function 0 sym53c8xx: IO region 0xd400[0..127] is in use apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) Creative EMU10K1 PCI Audio Driver, version 0.20, 19:27:06 Aug 10 2004 PCI: Enabling device 02:0e.0 (0004 -> 0005) PCI: Assigned IRQ 5 for device 02:0e.0 emu10k1: EMU10K1 rev 8 model 0x8040 found, IO at 0xd000-0xd01f, IRQ 5 ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23) PCI: Enabling device 02:0b.2 (0014 -> 0016) PCI: Assigned IRQ 10 for device 02:0b.2 ehci_hcd 02:0b.2: NEC Corporation USB 2.0 ehci_hcd 02:0b.2: irq 10, pci mem e0a84000 usb.c: new USB bus registered, assigned bus number 1 ehci_hcd 02:0b.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 hub.c: USB hub found hub.c: 5 ports detected PCI: Enabling device 02:0b.0 (0014 -> 0016) PCI: Found IRQ 9 for device 02:0b.0 PCI: Sharing IRQ 9 with 00:1f.4 usb-ohci.c: USB OHCI at membase 0xe0a8c000, IRQ 9 usb-ohci.c: usb-02:0b.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected PCI: Enabling device 02:0b.1 (0014 -> 0016) PCI: Found IRQ 9 for device 02:0b.1 PCI: Sharing IRQ 9 with 02:0c.0 usb-ohci.c: USB OHCI at membase 0xe0a8e000, IRQ 9 usb-ohci.c: usb-02:0b.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected uhci.c: USB Universal Host Controller Interface driver v1.1 PCI: Found IRQ 9 for device 00:1f.2 PCI: Setting latency timer of device 00:1f.2 to 64 uhci.c: USB UHCI at I/O 0xa400, IRQ 9 usb.c: new USB bus registered, assigned bus number 4 hub.c: new USB device 02:0b.2-3, assigned address 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 9 for device 00:1f.4 PCI: Sharing IRQ 9 with 02:0b.0 PCI: Setting latency timer of device 00:1f.4 to 64 uhci.c: USB UHCI at I/O 0xa000, IRQ 9 usb.c: USB device 2 (vend/prod 0x4a9/0x220f) is not claimed by any active driver. usb.c: new USB bus registered, assigned bus number 5 hub.c: USB hub found hub.c: 2 ports detected i810_rng: cannot register misc device i810_rng: cannot register misc device hub.c: new USB device 00:1f.2-1, assigned address 2 usb.c: USB device 2 (vend/prod 0x451/0xe001) is not claimed by any active driver. i810_rng: cannot register misc device hub.c: new USB device 00:1f.4-2, assigned address 2 hub.c: USB hub found hub.c: 4 ports detected i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device usb.c: registered new driver usbscanner scanner.c: USB scanner device (0x04a9/0x220f) now attached to scanner0 scanner.c: 0.4.16:USB Scanner Driver i810_rng: cannot register misc device i810_rng: cannot register misc device usb.c: registered new driver tiglusb tiglusb.c: firmware revision 1.03 tiglusb.c: TI-GRAPH LINK USB (aka SilverLink) driver, version 1.07 i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device i810_rng: cannot register misc device FAT: bogus logical sector size 0 VFS: Can't find a valid FAT filesystem on dev 02:00. hub.c: new USB device 02:0b.2-4, assigned address 3 usb.c: USB device 3 (vend/prod 0xd7d/0x1620) is not claimed by any active driver. Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage scsi1 : SCSI emulation for USB Mass Storage devices Vendor: Model: USB DISK Pro Rev: PMAP Type: Direct-Access ANSI SCSI revision: 02 Vendor: Model: USB DISK Pro Rev: PMAP Type: Direct-Access ANSI SCSI revision: 02 Attached scsi removable disk sde at scsi1, channel 0, id 0, lun 0 Attached scsi removable disk sdf at scsi1, channel 0, id 0, lun 1 SCSI device sde: 1004544 512-byte hdwr sectors (514 MB) sde: Write Protect is off /dev/scsi/host1/bus0/target0/lun0:<7>ldm_validate_partition_table(): Found an MS-DOS partition table, not a dynamic disk. p1 SCSI device sdf: 2880 512-byte hdwr sectors (1 MB) sdf: Write Protect is off /dev/scsi/host1/bus0/target0/lun1:<7>ldm_validate_partition_table(): Found an MS-DOS partition table, not a dynamic disk. p1 p2 p4 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 3 USB Mass Storage support registered. FAT: bogus logical sector size 7950 VFS: Can't find a valid FAT filesystem on dev 08:40. FAT: bogus logical sector size 7950 VFS: Can't find a valid FAT filesystem on dev 08:40. FAT: bogus logical sector size 7950 VFS: Can't find a valid FAT filesystem on dev 08:40. FAT: bogus logical sector size 7950 VFS: Can't find a valid FAT filesystem on dev 08:40.