This is my dmesg log file

dmesg.log (text/plain), 23.18 KB, created by Michael Sammels on 2009-06-07 10:56:32 UTC

Linux version 2.6.29-gentoo-r5 (root@localhost) (gcc version 4.3.2 (Gentoo 4.3.2-r3 p1.6, pie-10.1.5) ) #13 SMP Fri Jun 5 22:27:07 GMT 2009
Command line: root=/dev/sda3
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000dff90000 (usable)
 BIOS-e820: 00000000dff90000 - 00000000dff9e000 (ACPI data)
 BIOS-e820: 00000000dff9e000 - 00000000dffd0000 (ACPI NVS)
 BIOS-e820: 00000000dffd0000 - 00000000dffde000 (reserved)
 BIOS-e820: 00000000dffe0000 - 00000000e0000000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
last_pfn = 0xdff90 max_arch_pfn = 0x100000000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
init_memory_mapping: 0000000000000000-00000000dff90000
 0000000000 - 00dfe00000 page 2M
 00dfe00000 - 00dff90000 page 4k
kernel direct mapping tables up to dff90000 @ 10000-16000
last_map_addr: dff90000 end: dff90000
ACPI: RSDP 000FB7E0, 0024 (r2 ACPIAM)
ACPI: XSDT DFF90100, 0044 (r1 120508 XSDT1037 20081205 MSFT       97)
ACPI: FACP DFF90290, 00F4 (r3 120508 FACP1037 20081205 MSFT       97)
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT DFF905C0, 66E7 (r1  A1016 A1016000        0 INTL 20051117)
ACPI: FACS DFF9E000, 0040
ACPI: APIC DFF90390, 006C (r1 120508 APIC1037 20081205 MSFT       97)
ACPI: MCFG DFF90400, 003C (r1 120508 OEMMCFG  20081205 MSFT       97)
ACPI: OEMB DFF9E040, 0061 (r1 120508 OEMB1037 20081205 MSFT       97)
ACPI: Local APIC address 0xfee00000
(5 early reservations) ==> bootmem [0000000000 - 00dff90000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
  #2 [0001000000 - 00016db838]    TEXT DATA BSS ==> [0001000000 - 00016db838]
  #3 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
  #4 [0000010000 - 0000014000]          PGTABLE ==> [0000010000 - 0000014000]
found SMP MP-table at [ffff8800000ff780] 000ff780
 [ffffe20000000000-ffffe200031fffff] PMD -> [ffff880001800000-ffff8800049fffff] on node 0
Zone PFN ranges:
  DMA      0x00000010 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009f
    0: 0x00000100 -> 0x000dff90
On node 0 totalpages: 917279
  DMA zone: 56 pages used for memmap
  DMA zone: 105 pages reserved
  DMA zone: 3822 pages, LIFO batch:0
  DMA32 zone: 12487 pages used for memmap
  DMA32 zone: 900809 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
Allocating PCI resources starting at e2000000 (gap: e0000000:1ee00000)
NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Allocating 57344 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 904631
Kernel command line: root=/dev/sda3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 2663.619 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
Memory: 3603736k/3669568k available (3780k kernel code, 452k absent, 64856k reserved, 1879k data, 404k init)
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 5327.23 BogoMIPS (lpj=2663619)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
using mwait in idle threads.
ACPI: Core revision 20081204
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU     E8200  @ 2.66GHz stepping 06
APIC calibration not consistent with PM Timer: 118ms instead of 100ms
APIC delta adjusted to PM-Timer: 2081242 (2476317)
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5327.90 BogoMIPS (lpj=2663953)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU     E8200  @ 2.66GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (10655.14 BogoMIPS).
net_namespace: 1720 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
PCI: MCFG area at f0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at f0000000 - f3ffffff
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf9ffc000-0xf9ffffff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xd480-0xd49f]
pci 0000:00:1d.1: reg 20 io port: [0xd800-0xd81f]
pci 0000:00:1d.2: reg 20 io port: [0xd880-0xd89f]
pci 0000:00:1d.3: reg 20 io port: [0xdc00-0xdc1f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xf9ffbc00-0xf9ffbfff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x8f0-0x8f7]
pci 0000:00:1f.1: reg 1c io port: [0x8f8-0x8fb]
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.2: reg 10 io port: [0xd400-0xd407]
pci 0000:00:1f.2: reg 14 io port: [0xd080-0xd083]
pci 0000:00:1f.2: reg 18 io port: [0xd000-0xd007]
pci 0000:00:1f.2: reg 1c io port: [0xcc00-0xcc03]
pci 0000:00:1f.2: reg 20 io port: [0xc880-0xc88f]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff]
pci 0000:01:00.0: reg 24 io port: [0xec00-0xec7f]
pci 0000:01:00.0: reg 30 32bit mmio: [0xfeb80000-0xfebfffff]
pci 0000:00:01.0: bridge io port: [0xe000-0xefff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfa000000-0xfebfffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - 8C, should be 7F [20081204]
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:08: ioport range 0x290-0x297 has been reserved
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x800-0x87f has been reserved
system 00:09: ioport range 0x480-0x4bf has been reserved
system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:0b: iomem range 0xffc00000-0xffefffff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0f: iomem range 0xf0000000-0xf3ffffff has been reserved
system 00:10: iomem range 0x0-0x9ffff could not be reserved
system 00:10: iomem range 0xc0000-0xcffff has been reserved
system 00:10: iomem range 0xe0000-0xfffff could not be reserved
system 00:10: iomem range 0x100000-0xdfffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: 0xe000-0xefff
pci 0000:00:01.0:   MEM window: 0xfa000000-0xfebfffff
pci 0000:00:01.0:   PREFETCH window: 0x000000e0000000-0x000000efffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: disabled
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io:  [0xe000-0xefff]
pci_bus 0000:01: resource 1 mem: [0xfa000000-0xfebfffff]
pci_bus 0000:01: resource 2 mem: [0xe0000000-0xefffffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 mem: [0x0-0x0]
pci_bus 0000:02: resource 1 mem: [0x0-0x0]
pci_bus 0000:02: resource 2 mem: [0x0-0x0]
pci_bus 0000:02: resource 3 io:  [0x00-0xffff]
pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Microcode Update Driver: v2.00 <[e-mail]>, Peter Oruba
audit: initializing netlink socket (disabled)
type=2000 audit(1244324825.180:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
NTFS driver 2.1.29 [Flags: R/W DEBUG].
msgmni has been set to 7039
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT DFF9E0B0, 01D2 (r1    AMI   CPU1PM        1 INTL 20060113)
processor ACPI_CPU:00: registered as cooling_device0
ACPI: SSDT DFF9E290, 0143 (r1    AMI   CPU2PM        1 INTL 20060113)
processor ACPI_CPU:01: registered as cooling_device1
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0e: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
brd: module loaded
loop: module loaded
nbd: registered device at major 43
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Loading iSCSI transport class v2.0-870.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xc880 irq 19
ata4: SATA max UDMA/133 cmd 0xd000 ctl 0xcc00 bmdma 0xc888 irq 19
ata3.01: ATAPI: ASUS    DRW-2014L1T, 1.02, max UDMA/66
ata3.01: configured for UDMA/66
isa bounce pool size: 16 pages
scsi 2:0:1:0: CD-ROM            ASUS     DRW-2014L1T      1.02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
sr 2:0:1:0: Attached scsi generic sg0 type 5
ata4.00: ATA-8: ST31500341AS, CC1H, max UDMA/133
ata4.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.01: ATA-8: ST31000340AS, SD15, max UDMA/133
ata4.01: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
ata4.01: configured for UDMA/133
scsi 3:0:0:0: Direct-Access     ATA      ST31500341AS     CC1H PQ: 0 ANSI: 5
sd 3:0:0:0: [sda] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sda] 2930277168 512-byte hardware sectors: (1.50 TB/1.36 TiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 3:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg1 type 0
scsi 3:0:1:0: Direct-Access     ATA      ST31000340AS     SD15 PQ: 0 ANSI: 5
sd 3:0:1:0: [sdb] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 3:0:1:0: [sdb] Write Protect is off
sd 3:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:1:0: [sdb] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
sd 3:0:1:0: [sdb] Write Protect is off
sd 3:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1
sd 3:0:1:0: [sdb] Attached SCSI disk
sd 3:0:1:0: Attached scsi generic sg2 type 0
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9ffbc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d480
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000dc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
cpuidle: using governor ladder
cpuidle: using governor menu
No iBFT detected.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
EXT3-fs: sda3: couldn't mount because of unsupported optional features (40).
EXT2-fs: sda3: couldn't mount because of unsupported optional features (40).
EXT4-fs: barriers enabled
kjournald2 starting: pid 724, dev sda3:8, commit interval 5 seconds
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sda3 with ordered data mode
VFS: Mounted root (ext4 filesystem) readonly on device 8:3.
Freeing unused kernel memory: 404k freed
usb 1-4: new high speed USB device using ehci_hcd and address 2
usb 1-4: configuration #1 chosen from 1 choice
hub 1-4:1.0: USB hub found
hub 1-4:1.0: 4 ports detected
usb 1-4.1: new high speed USB device using ehci_hcd and address 3
usb 1-4.1: configuration #1 chosen from 1 choice
usb 1-4.2: new high speed USB device using ehci_hcd and address 4
usb 1-4.2: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb 1-4.4: new low speed USB device using ehci_hcd and address 5
usb 1-4.4: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/1-4.4:1.0/input/input4
logitech 0003:046D:C517.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.7-4.4/input0
logitech 0003:046D:C517.0002: fixing up Logitech keyboard report descriptor
input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/1-4.4:1.1/input/input5
logitech 0003:046D:C517.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.7-4.4/input1
wmaster0 (rtl8187): not using net_device_ops yet
phy0: Selected rate control algorithm 'minstrel'
wlan0 (rtl8187): not using net_device_ops yet
phy0: hwaddr 00:0f:b5:d0:84:d9, RTL8187vB (default) V1 + rtl8225
usbcore: registered new interface driver rtl8187
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:1b.0: setting latency timer to 64
nvidia: module license 'NVIDIA' taints kernel.
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  180.29  Wed Feb  4 23:39:47 PST 2009
EXT4 FS on sda3, internal journal on sda3:8
EXT4-fs: barriers enabled
kjournald2 starting: pid 1647, dev sdb1:8, commit interval 5 seconds
EXT4 FS on sdb1, internal journal on sdb1:8
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: mounted filesystem sdb1 with ordered data mode
Adding 2104504k swap on /dev/sda2.  Priority:-1 extents:1 across:2104504k