full xorg.conf

xorg.conf (text/plain), 3.85 KB, created by Panard on 2009-05-04 21:30:16 UTC

Section "Files"
    FontPath	"/usr/share/fonts/dejavu"
    FontPath	"/usr/share/fonts/misc"
    FontPath	"/usr/share/fonts/75dpi"
    FontPath	"/usr/share/fonts/100dpi"

#    ModulePath	"/usr/lib64/xorg/modules"
EndSection


Section "Module"
    Load	"dbe"

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
#    SubSection	"extmod"
#	Option	"omit xfree86-dga"
#    EndSubSection

#    Load	"freetype"
EndSection


# **********************************************************************
# Server flags section.  This contains various server-wide Options.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option	"NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option	"DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option	"DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option	"DontZoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option	"DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option	"AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

#    Option	"DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

#    Option	"AllowNonLocalModInDev"

# Set the basic blanking screen saver timeout.

    Option	"blank time"	"10"	# 10 minutes

# Set the DPMS timeouts.  These are set here because they are global
# rather than screen-specific.  These settings alone don't enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.

    Option	"standby time"	"20"
    Option	"suspend time"	"30"
    Option	"off time"	"60"

# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don't overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.

# Option   "EstimateSizesAggresively" "0"

EndSection

Section "Monitor"
	Identifier "Auto monitor"
EndSection

Section "Device"
	Identifier "Auto device"
EndSection

Section "Screen"
	Identifier "LVDS"
	Device "Auto device"
	Monitor "Auto monitor"

	DefaultDepth	24

	SubSection "Display"
		Depth		8
		Modes		"1280x800"
		Modes		"1024x768"
		Modes		"800x600"
		Option		"rgb bits" "8"
		Visual		"StaticColor"
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1280x800"
		Modes		"1024x768"
		Modes		"800x600"
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1280x800"
		Modes		"1024x768"
		Modes		"800x600"
	EndSubSection
EndSection

Section "InputDevice"
	Driver "wacom"
	Identifier "stylus"
	Option "Device" "/dev/ttyS0"
	Option "Type" "stylus"
	Option "ForceDevice" "ISDV4"
EndSection

Section "InputDevice"
	Driver "wacom"
	Identifier "eraser"
	Option "Device" "/dev/ttyS0"
	Option "Type" "eraser"
	Option "ForceDevice" "ISDV4"
EndSection

Section "ServerLayout"
	Identifier "default"
	Screen "LVDS"
	InputDevice "stylus" "SendCoreEvents"
	InputDevice "eraser" "SendCoreEvents"
EndSection