Patches needed for upcoming 1.4 maint release.

gentoo-x86-install-14maint.diff (text/plain), 3.26 KB, created by Daniel Robbins (RETIRED) on 2003-09-12 10:14:05 UTC

--- gentoo-x86-install.xml	2003-09-12 11:10:44.000000000 -0600
+++ gentoo-x86-install-drob.xml	2003-09-11 21:03:25.000000000 -0600
@@ -250,6 +250,10 @@
 </p>
 
 <table>
+<tcolumn width="0.75in"/>
+<tcolumn width="1in"/>
+<tcolumn width="1.25in"/>
+<tcolumn width="3.5in"/>
 <tr>
  <th>Stage Tarball</th>
  <th>Internet Access Required</th>
@@ -320,6 +324,8 @@
 </p>
 
 <table>
+<tcolumn width="2in"/>
+<tcolumn width="4in"/>
 <tr><th>Available kernels</th><th>Description</th></tr>
 <tr><ti>gentoo</ti><ti>standard gentoo kernel (default)</ti></tr>
 <tr><ti>nofb</ti><ti>framebuffer mode disabled</ti></tr>
@@ -329,6 +335,8 @@
 </table>
 
 <table>
+<tcolumn width="2in"/>
+<tcolumn width="4in"/>
 <tr><th>Available boot options</th><th>Description</th></tr>
 <tr><ti>doataraid</ti><ti>loads ide raid modules from initrd</ti></tr>
 <tr><ti>dofirewire</ti><ti>modprobes firewire modules in initrd (for firewire cdroms,etc.)</ti></tr>
@@ -582,6 +590,9 @@
 </p>
 
 <table>
+<tcolumn width="1.25in"/>
+<tcolumn width="4in"/>
+<tcolumn width="1.25in"/>
 <tr><th>Information</th><th>Description</th><th>Example value</th></tr>
 <tr><ti>IP address</ti><ti>The IP address you want to assign to your network card</ti><ti>192.168.1.2</ti></tr>
 <tr><ti>Broadcast address</ti><ti>The IP address which will broadcast the packets to all the hosts in the network</ti><ti>192.168.1.255</ti></tr>
@@ -926,6 +937,10 @@
 </p>
 
 <table>
+<tcolumn width="1.5in"/>
+<tcolumn width="2.5in"/>
+<tcolumn width="2.5in"/>
+<tcolumn width="1in"/>
 <tr>
  <th>Partition</th>
  <th>Size</th>
@@ -2146,6 +2161,9 @@
 </p>
 
 <table>
+<tcolumn width="1in"/>
+<tcolumn width="4in"/>
+<tcolumn width="2in"/>
 <tr>
  <th>Ebuild</th>
  <th>Purpose</th>
@@ -2298,14 +2316,18 @@
 <pre caption="Installing rp-pppoe">
 # <i>USE="-X" emerge rp-pppoe</i>
 <comment>GRP users should type the following:</comment>
-# <i>USE="-X bindist" emerge -K rp-pppoe</i>
+# <i>emerge -K rp-pppoe</i>
 </pre>
 
 <note>
 The <i>USE="-X"</i> prevents pppoe from installing its optional X interface, 
 which is a good thing, because X and its dependencies would also be emerged. 
-You can always recompile <i>rp-pppoe</i> with X support later.
+You can always recompile <i>rp-pppoe</i> with X support later. The GRP version
+of rp-pppoe has the optional X interface enabled. If you're not using GRP, compile from
+source as in the first example.
 </note>
+<!-- this pkg is a candidate for moving from .tbz2 to distfiles/ (source) -->
+
 
 <note>
 Please note that the rp-pppoe is built but not configured. You will have to 
@@ -2853,6 +2875,10 @@
 </p>
 
 <table>
+<tcolumn width="1in"/>
+<tcolumn width="1in"/>
+<tcolumn width="1in"/>
+<tcolumn width="1in"/>
 <tr><ti></ti><th>640x480</th><th>800x600</th><th>1024x768</th><th>1280x1024</th></tr>
 <tr><th>8 bpp</th><ti>769</ti><ti>771</ti><ti>773</ti><ti>775</ti></tr>
 <tr><th>16 bpp</th><ti>785</ti><ti>788</ti><ti>791</ti><ti>794</ti></tr>
@@ -2937,8 +2963,7 @@
 </p>
 
 <pre caption="Installing from GRP">
-# <i>USE="bindist" emerge -k xfree</i> 
-<codenote>(USE="bindist" must be set while installing GRP packages that use XFree86)</codenote>
+# <i>emerge -k xfree</i> 
 </pre>
 
 <p>
@@ -2961,7 +2986,7 @@
 </p>
 
 <pre caption="Installing KDE from GRP">
-# <i>USE="bindist" emerge -k kde</i>
+# <i>emerge -k kde</i>
 </pre>
 
 </body>