Linux version 2.6.24-gentoo-r8 (root@chef-rechner) (gcc version 4.1.2 (Gentoo 4.1.2 p1.1)) #4 SMP PREEMPT Thu Dec 11 21:42:45 CET 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
 BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
 BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
 BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000e4000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
1150MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5150
Entering add_active_range(0, 0, 524000) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   524000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   524000
On node 0 totalpages: 524000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 2301 pages used for memmap
  HighMem zone: 292323 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
DMI 2.4 present.
ACPI: RSDP 000F6B40, 0014 (r0 GBT   )
ACPI: RSDT 7FEE3040, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: FACP 7FEE30C0, 0074 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: DSDT 7FEE3180, 4B2A (r1 GBT    GBTUACPI     1000 MSFT  100000C)
ACPI: FACS 7FEE0000, 0040
ACPI: HPET 7FEE7E00, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU       98)
ACPI: MCFG 7FEE7E80, 003C (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: APIC 7FEE7D00, 0084 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: SSDT 7FEE8520, 03AB (r1  PmRef    CpuPm     3000 INTL 20040311)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519907
Kernel command line: auto BOOT_IMAGE=Gentoo6 ro root=803 real_root=/dev/sda3 video=uvesafb:1280x1024-32,mtrr:3,ywrap log_buf_len=64k
log_buf_len: 65536
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2666.737 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2072772k/2096000k available (3123k kernel code, 22176k reserved, 1089k data, 276k init, 1178496k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc0524000 - 0xc0569000   ( 276 kB)
      .data : 0xc040cc79 - 0xc051d25c   (1089 kB)
      .text : 0xc0100000 - 0xc040cc79   (3123 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 5336.12 BogoMIPS (lpj=2668060)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3fd 00000000 00000001 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3fd 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Core(TM)2 Duo CPU     E6750  @ 2.66GHz stepping 0b
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5333.31 BogoMIPS (lpj=2666655)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3fd 00000000 00000001 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3fd 00000000 00000001 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 Duo CPU     E6750  @ 2.66GHz stepping 0b
Total of 2 processors activated (10669.43 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
net_namespace: 64 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnpacpi: exceeded the max number of mem resources: 12
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x290-0x29f has been reserved
system 00:01: ioport range 0x800-0x87f has been reserved
system 00:01: ioport range 0x290-0x294 has been reserved
system 00:01: ioport range 0x880-0x88f has been reserved
system 00:09: ioport range 0x400-0x4bf could not be reserved
system 00:0a: iomem range 0xe0000000-0xe3ffffff could not be reserved
system 00:0b: iomem range 0xcd200-0xcffff has been reserved
system 00:0b: iomem range 0xf0000-0xf7fff could not be reserved
system 00:0b: iomem range 0xf8000-0xfbfff could not be reserved
system 00:0b: iomem range 0xfc000-0xfffff could not be reserved
system 00:0b: iomem range 0x7fee0000-0x7fefffff could not be reserved
system 00:0b: iomem range 0x0-0x9ffff could not be reserved
system 00:0b: iomem range 0x100000-0x7fedffff could not be reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0b: iomem range 0xfed10000-0xfed1dfff could not be reserved
system 00:0b: iomem range 0xfed20000-0xfed8ffff could not be reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0b: iomem range 0xffb00000-0xffb7ffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: a000-afff
  MEM window: e4000000-e7ffffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:1c.0
  IO window: 9000-9fff
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
  IO window: b000-bfff
  MEM window: ea000000-ea0fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
  IO window: c000-cfff
  MEM window: e8000000-e9ffffff
  PREFETCH window: 80000000-800fffff
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: ea100000-ea1fffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered (default)
io scheduler cfq registered
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
Allocate Port Service[0000:00:1c.3:pcie03]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
Allocate Port Service[0000:00:1c.4:pcie03]
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
[drm] Initialized drm 1.1.0 20060810
uvesafb: NVIDIA Corporation, G84 Board - p403h05 - p403h05 , Chip Rev   , OEM: NVIDIA, VBE v3.0
uvesafb: protected mode interface info at c000:b6e0
uvesafb: pmi: set display start = c00cb743, set palette = c00cb79e
uvesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
uvesafb: VBIOS/hardware doesn't support DDC transfers
uvesafb: no monitor limits have been set, default refresh rate will be used
uvesafb: scrolling: ywrap using protected mode interface, yres_virtual=2867
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Console: switching to colour frame buffer device 160x64
uvesafb: framebuffer at 0xe5000000, mapped to 0xf8880000, using 14336k, total 14336k
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT 7FEE7F00, 022A (r1  PmRef  Cpu0Ist     3000 INTL 20040311)
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 7FEE83C0, 0152 (r1  PmRef  Cpu1Ist     3000 INTL 20040311)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:04:00.0 to 64
r8169 0000:04:00.0: no MSI. Back to INTx.
eth0: RTL8168b/8111b at 0xf8828000, 00:1d:7d:9d:60:30, XID 38000000 IRQ 16
Linux video capture interface: v2.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:03:00.0: version 3.0
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 19 (level, low) -> IRQ 17
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:03:00.0 to 64
scsi0 : ahci
scsi1 : ahci
ata1: SATA max UDMA/133 abar m8192@0xea000000 port 0xea000100 irq 17
ata2: SATA max UDMA/133 abar m8192@0xea000000 port 0xea000180 irq 17
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xd600 ctl 0xd700 bmdma 0xda00 irq 17
ata4: SATA max UDMA/133 cmd 0xd800 ctl 0xd900 bmdma 0xda08 irq 17
ata3.00: ATAPI: ASUS    DRW-2014L1T, 1.00, max UDMA/66
ata3.00: configured for UDMA/66
ata4.00: HPA detected: current 976771055, native 976773168
ata4.00: ATA-7: ST3500641AS, 3.AAJ, max UDMA/133
ata4.00: 976771055 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
scsi 2:0:0:0: CD-ROM            ASUS     DRW-2014L1T      1.00 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr 2:0:0:0: Attached scsi generic sg0 type 5
scsi 3:0:0:0: Direct-Access     ATA      ST3500641AS      3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sda] 976771055 512-byte hardware sectors (500107 MB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 >
sd 3:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg1 type 0
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata5: SATA max UDMA/133 cmd 0xdd00 ctl 0xde00 bmdma 0xe100 irq 17
ata6: SATA max UDMA/133 cmd 0xdf00 ctl 0xe000 bmdma 0xe108 irq 17
ieee1394: raw1394: /dev/raw1394 device initialized
NOTE: The dv1394 driver is unsupported and may be removed in a future Linux release. Use raw1394 instead.
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xea205000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xea204000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d100
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 20, io base 0x0000d200
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.2 to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000d000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000d300
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 4-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000d400
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d500
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
usb 4-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
usb 4-2: new low speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
input: B16_b_02 USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1a.1-1
input: BTC USB Multimedia Keyboard as /class/input/input3
input: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-0000:00:1a.1-2
input: BTC USB Multimedia Keyboard as /class/input/input4
input: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:1a.1-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC).
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
ALSA device list:
  #0: HDA Intel at 0xea200000 irq 21
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.5
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Starting balanced_irq
Using IPI No-Shortcut mode
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
EXT3-fs: sda3: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 1359906
ext3_orphan_cleanup: deleting unreferenced inode 1359948
ext3_orphan_cleanup: deleting unreferenced inode 4260052
ext3_orphan_cleanup: deleting unreferenced inode 1359952
ext3_orphan_cleanup: deleting unreferenced inode 1359950
ext3_orphan_cleanup: deleting unreferenced inode 1359914
ext3_orphan_cleanup: deleting unreferenced inode 1359938
ext3_orphan_cleanup: deleting unreferenced inode 1359947
ext3_orphan_cleanup: deleting unreferenced inode 1359945
ext3_orphan_cleanup: deleting unreferenced inode 1359936
ext3_orphan_cleanup: deleting unreferenced inode 1359941
ext3_orphan_cleanup: deleting unreferenced inode 1359939
ext3_orphan_cleanup: deleting unreferenced inode 1359943
ext3_orphan_cleanup: deleting unreferenced inode 1359937
ext3_orphan_cleanup: deleting unreferenced inode 4740200
kjournald starting.  Commit interval 5 seconds
ext3_orphan_cleanup: deleting unreferenced inode 1359924
ext3_orphan_cleanup: deleting unreferenced inode 1359923
ext3_orphan_cleanup: deleting unreferenced inode 1359922
ext3_orphan_cleanup: deleting unreferenced inode 1359921
ext3_orphan_cleanup: deleting unreferenced inode 1359920
ext3_orphan_cleanup: deleting unreferenced inode 1359919
ext3_orphan_cleanup: deleting unreferenced inode 1359909
ext3_orphan_cleanup: deleting unreferenced inode 1359908
ext3_orphan_cleanup: deleting unreferenced inode 1359903
EXT3-fs: sda3: 24 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 276k freed
ACPI: PCI Interrupt 0000:05:00.1[A] -> GSI 20 (level, low) -> IRQ 22
bt87x0: Using board 1, analog, digital (rate 32000 Hz)
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 22
bttv0: Bt878 (rev 17) at 0000:05:00.0, irq: 22, latency: 32, mmio: 0xea100000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 1-0050: Hauppauge model 44354, rev B121, serial# 2146188
tveeprom 1-0050: tuner model is Philips FM1216 (idx 21, type 5)
tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 1-0050: audio processor is MSP3415 (idx 6)
tveeprom 1-0050: has radio
bttv0: Hauppauge eeprom indicates model#44354
bttv0: tuner type=5
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp3400 1-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
msp3400 1-0040: MSP3415D-B3 supports nicam, mode is autodetect
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
nvidia: module license 'NVIDIA' taints kernel.
tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner-simple 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
tuner 1-0061: type set to Philips PAL_BG (FI1
tuner-simple 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
tuner 1-0061: type set to Philips PAL_BG (FI1
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bt878: AUDIO driver version 0.0.0 loaded
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module  177.80  Wed Oct  1 14:38:10 PDT 2008
EXT3 FS on sda3, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda5, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 7815612k swap on /dev/sda2.  Priority:-1 extents:1 across:7815612k
r8169: eth0: link up
r8169: eth0: link up