dmesg from -r4 (i.e. non-working)

dmesg.bad (text/plain), 34.14 KB, created by Leonid Podolny on 2008-11-23 18:46:12 UTC

Linux version 2.6.27-gentoo-r4 (root@looptop) (gcc version 4.3.2 (Gentoo 4.3.2 p1.0) ) #1 SMP PREEMPT Sat Nov 22 14:46:17 IST 2008
Command line: video=uvesafb:1280x800-32,mtrr:3 root=/dev/sda2 
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009ac00 (usable)
 BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000bf7a0000 (usable)
 BIOS-e820: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data)
 BIOS-e820: 00000000bf7ae000 - 00000000bf7f0000 (ACPI NVS)
 BIOS-e820: 00000000bf7f0000 - 00000000bf800000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
DMI present.
AMI BIOS detected: BIOS may corrupt low RAM, working it around.
last_pfn = 0xbf7a0 max_arch_pfn = 0x3ffffffff
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
init_memory_mapping
 0000000000 - 00bf600000 page 2M
 00bf600000 - 00bf7a0000 page 4k
kernel direct mapping tables up to bf7a0000 @ 10000-15000
last_map_addr: bf7a0000 end: bf7a0000
ACPI: RSDP 000F8CA0, 0014 (r0 ACPIAM)
ACPI: RSDT BF7A0000, 0044 (r1 040808 RSDT1328 20080408 MSFT       97)
ACPI: FACP BF7A0200, 0084 (r2 040808 FACP1328 20080408 MSFT       97)
ACPI: DSDT BF7A05B0, 5ACD (r1  A1221 A1221000        0 INTL 20051117)
ACPI: FACS BF7AE000, 0040
ACPI: APIC BF7A0390, 005C (r1 040808 APIC1328 20080408 MSFT       97)
ACPI: MCFG BF7A03F0, 003C (r1 040808 OEMMCFG  20080408 MSFT       97)
ACPI: SLIC BF7A0430, 0176 (r1 040808 SLIC1328 20080408 MSFT       97)
ACPI: OEMB BF7AE040, 0071 (r1 040808 OEMB1328 20080408 MSFT       97)
ACPI: HPET BF7A6080, 0038 (r1 040808 OEMHPET  20080408 MSFT       97)
ACPI: GSCI BF7AE0C0, 2024 (r1 040808 GMCHSCI  20080408 MSFT       97)
ACPI: SSDT BF7B0A90, 04F0 (r1  PmRef    CpuPm     3000 INTL 20051117)
(5 early reservations) ==> bootmem [0000000000 - 00bf7a0000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
  #2 [0000200000 - 00006f9d58]    TEXT DATA BSS ==> [0000200000 - 00006f9d58]
  #3 [000009ac00 - 0000100000]    BIOS reserved ==> [000009ac00 - 0000100000]
  #4 [0000010000 - 0000013000]          PGTABLE ==> [0000010000 - 0000013000]
 [ffffe20000000000-ffffe200029fffff] PMD -> [ffff880001200000-ffff880003bfffff] on node 0
Zone PFN ranges:
  DMA      0x00000010 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009a
    0: 0x00000100 -> 0x000bf7a0
On node 0 totalpages: 784170
  DMA zone: 2542 pages, LIFO batch:0
  DMA32 zone: 769525 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009a000 - 000000000009b000
PM: Registered nosave memory: 000000000009b000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at c0000000 (gap: bf800000:3f600000)
PERCPU: Allocating 46212 bytes of per cpu data
NR_CPUS: 8, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 772067
Kernel command line: video=uvesafb:1280x800-32,mtrr:3 root=/dev/sda2 
Initializing CPU#0
Preemptible RCU implementation.
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC: PIT calibration confirmed by PMTIMER.
TSC: using PIT calibration value
Detected 2194.476 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
No AGP bridge found
Memory: 3081508k/3137152k available (3053k kernel code, 54596k reserved, 1177k data, 340k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
Calibrating delay loop (skipped), value calculated using timer frequency.. 4388.95 BogoMIPS (lpj=2194476)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
ACPI: Core revision 20080609
Parsing all Control Methods:
Table [DSDT](id 0001) - 899 Objects with 70 Devices 209 Methods 32 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 15 Objects with 0 Devices 4 Methods 0 Regions
 tbxface-0596 [02] tb_load_namespace     : ACPI Tables successfully acquired
evxfevnt-0091 [02] enable                : Transition to ACPI mode successful
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU     T7500  @ 2.20GHz stepping 0b
Using local APIC timer interrupts.
APIC timer calibration result 12468610
Detected 12.468 MHz APIC timer.
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4388.77 BogoMIPS (lpj=2194387)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU     T7500  @ 2.20GHz stepping 0b
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8777.72 BogoMIPS).
net_namespace: 1464 bytes
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
evgpeblk-0957 [04] ev_create_gpe_block   : GPE 00 to 1F [_GPE] 4 regs on int 0x9
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package initialization:..................................................................................................................................
Initialized 28/32 Regions 26/26 Fields 40/41 Buffers 36/36 Packages (923 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:
Executed 0 _INI methods requiring 0 _STA executions (examined 75 objects)
evgpeblk-1054 [03] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 3 Runtime GPEs in this block
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
ACPI Error (evregion-0315): No handler for Region [EC__] (ffff8800bf0133a8) [EmbeddedControl] [20080609]
ACPI Error (exfldio-0291): Region EmbeddedControl(3) has no handler [20080609]
ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST
ACPI Error (uteval-0232): Method execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST
ACPI Error (evregion-0315): No handler for Region [EC__] (ffff8800bf0133a8) [EmbeddedControl] [20080609]
ACPI Error (exfldio-0291): Region EmbeddedControl(3) has no handler [20080609]
ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST
ACPI Error (uteval-0232): Method execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: Using MMCONFIG at e0000000 - efffffff
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: 0000:00:02.0 reg 10 64bit mmio: [fda00000, fdafffff]
PCI: 0000:00:02.0 reg 18 64bit mmio: [d0000000, dfffffff]
PCI: 0000:00:02.0 reg 20 io port: [b480, b487]
PCI: 0000:00:02.1 reg 10 64bit mmio: [fdb00000, fdbfffff]
PCI: 0000:00:1a.0 reg 20 io port: [b800, b81f]
PCI: 0000:00:1a.1 reg 20 io port: [b880, b89f]
PCI: 0000:00:1a.7 reg 10 32bit mmio: [fdcff000, fdcff3ff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
PCI: 0000:00:1b.0 reg 10 64bit mmio: [fdcf8000, fdcfbfff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
PCI: 0000:00:1d.0 reg 20 io port: [bc00, bc1f]
PCI: 0000:00:1d.1 reg 20 io port: [c000, c01f]
PCI: 0000:00:1d.2 reg 20 io port: [c080, c09f]
PCI: 0000:00:1d.7 reg 10 32bit mmio: [fdcff400, fdcff7ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
PCI: 0000:00:1f.1 reg 18 io port: [8f0, 8f7]
PCI: 0000:00:1f.1 reg 1c io port: [8f8, 8fb]
PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf]
PCI: 0000:00:1f.2 reg 10 io port: [cc00, cc07]
PCI: 0000:00:1f.2 reg 14 io port: [c880, c883]
PCI: 0000:00:1f.2 reg 18 io port: [c800, c807]
PCI: 0000:00:1f.2 reg 1c io port: [c480, c483]
PCI: 0000:00:1f.2 reg 20 io port: [c400, c41f]
PCI: 0000:00:1f.2 reg 24 32bit mmio: [fdcff800, fdcfffff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
PCI: bridge 0000:00:1c.0 io port: [e000, efff]
PCI: bridge 0000:00:1c.0 32bit mmio: [fe000000, febfffff]
PCI: bridge 0000:00:1c.0 64bit mmio pref: [fa000000, fcffffff]
PCI: 0000:03:00.0 reg 10 io port: [d800, d8ff]
PCI: 0000:03:00.0 reg 18 64bit mmio: [fdfff000, fdffffff]
PCI: 0000:03:00.0 reg 30 32bit mmio: [fdfc0000, fdfdffff]
pci 0000:03:00.0: supports D1
pci 0000:03:00.0: supports D2
pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:00.0: PME# disabled
PCI: bridge 0000:00:1c.1 io port: [d000, dfff]
PCI: bridge 0000:00:1c.1 32bit mmio: [fdf00000, fdffffff]
PCI: 0000:02:00.0 reg 10 64bit mmio: [fdefe000, fdefffff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
PCI: bridge 0000:00:1c.2 32bit mmio: [fde00000, fdefffff]
PCI: 0000:01:04.0 reg 10 32bit mmio: [fddff000, fddff07f]
pci 0000:01:04.0: supports D1
pci 0000:01:04.0: supports D2
pci 0000:01:04.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:04.0: PME# disabled
PCI: 0000:01:04.1 reg 10 32bit mmio: [fddff400, fddff4ff]
pci 0000:01:04.1: supports D1
pci 0000:01:04.1: supports D2
pci 0000:01:04.1: PME# supported from D0 D1 D2 D3hot
pci 0000:01:04.1: PME# disabled
PCI: 0000:01:04.2 reg 10 32bit mmio: [fddff800, fddff87f]
pci 0000:01:04.2: supports D1
pci 0000:01:04.2: supports D2
pci 0000:01:04.2: PME# supported from D0 D1 D2 D3hot
pci 0000:01:04.2: PME# disabled
PCI: 0000:01:04.3 reg 10 32bit mmio: [fddffc00, fddffcff]
pci 0000:01:04.3: supports D1
pci 0000:01:04.3: supports D2
pci 0000:01:04.3: PME# supported from D0 D1 D2 D3hot
pci 0000:01:04.3: PME# disabled
pci 0000:00:1e.0: transparent bridge
PCI: bridge 0000:00:1e.0 32bit mmio: [fdd00000, fddfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 *15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:08: ioport range 0x400-0x41f has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x500-0x53f has been reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed40000-0xfed8ffff has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0xc0000-0xcffff has been reserved
system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
system 00:0c: iomem range 0x100000-0xbf7fffff could not be reserved
system 00:0c: iomem range 0xfed90000-0xffffffff could not be reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.0:   IO window: 0xe000-0xefff
pci 0000:00:1c.0:   MEM window: 0xfe000000-0xfebfffff
pci 0000:00:1c.0:   PREFETCH window: 0x000000fa000000-0x000000fcffffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1:   IO window: 0xd000-0xdfff
pci 0000:00:1c.1:   MEM window: 0xfdf00000-0xfdffffff
pci 0000:00:1c.1:   PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.2:   IO window: disabled
pci 0000:00:1c.2:   MEM window: 0xfde00000-0xfdefffff
pci 0000:00:1c.2:   PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: 0xfdd00000-0xfddfffff
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [0, ffffffffffffffff]
bus: 04 index 0 io port: [e000, efff]
bus: 04 index 1 mmio: [fe000000, febfffff]
bus: 04 index 2 mmio: [fa000000, fcffffff]
bus: 04 index 3 mmio: [0, 0]
bus: 03 index 0 io port: [d000, dfff]
bus: 03 index 1 mmio: [fdf00000, fdffffff]
bus: 03 index 2 mmio: [0, 0]
bus: 03 index 3 mmio: [0, 0]
bus: 02 index 0 mmio: [0, 0]
bus: 02 index 1 mmio: [fde00000, fdefffff]
bus: 02 index 2 mmio: [0, 0]
bus: 02 index 3 mmio: [0, 0]
bus: 01 index 0 mmio: [0, 0]
bus: 01 index 1 mmio: [fdd00000, fddfffff]
bus: 01 index 2 mmio: [0, 0]
bus: 01 index 3 io port: [0, ffff]
bus: 01 index 4 mmio: [0, ffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
IA-32 Microcode Update Driver: v1.14a <[e-mail]>
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 6019
io scheduler noop registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: found MSI capability
pci_express 0000:00:1c.1:pcie00: allocate port service
pci_express 0000:00:1c.1:pcie02: allocate port service
pci_express 0000:00:1c.1:pcie03: allocate port service
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.2: found MSI capability
pci_express 0000:00:1c.2:pcie00: allocate port service
pci_express 0000:00:1c.2:pcie02: allocate port service
pci_express 0000:00:1c.2:pcie03: allocate port service
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 965GM Chipset
agpgart-intel 0000:00:00.0: detected 7676K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
uvesafb: Intel Corporation, Intel(r)GM965/PM965/GL960 Graphics Controller, Hardware Version 0.0, OEM: Intel(r)GM965/PM965/GL960 Graphics Chip Accelerated VGA BIOS, VBE v3.0
uvesafb: VBIOS/hardware supports DDC2 transfers
uvesafb: monitor limits: vf = 60 Hz, hf = 49 kHz, clk = 68 MHz
uvesafb: scrolling: redraw
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Console: switching to colour frame buffer device 160x50
uvesafb: framebuffer at 0xd0000000, mapped to 0xffffc20010300000, using 7616k, total 7616k
fb0: VESA VGA frame buffer device
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8169 0000:03:00.0: setting latency timer to 64
eth0: RTL8168b/8111b at 0xffffc2000002c000, 00:1d:92:51:62:f7, XID 38000000 IRQ 508
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ems 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfdcff800 port 0xfdcff900 irq 507
ata2: SATA max UDMA/133 abar m2048@0xfdcff800 port 0xfdcff980 irq 507
ata3: SATA max UDMA/133 abar m2048@0xfdcff800 port 0xfdcffa00 irq 507
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: TOSHIBA MK1646GSX, LB111A, max UDMA/100
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK1646GS LB11 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WA03, max UDMA/33
ata4.00: configured for UDMA/33
ata5: port disabled. ignoring.
isa bounce pool size: 16 pages
scsi 3:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T20N  WA03 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
sr 3:0:0:0: Attached scsi generic sg1 type 5
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdcff000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.27-gentoo-r4 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdcff400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.27-gentoo-r4 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000bc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.1
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c080
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.2
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, hpet irqs
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [e-mail]
cpuidle: using governor ladder
cpuidle: using governor menu
usb 7-1: new full speed USB device using uhci_hcd and address 2
usb 7-1: configuration #1 chosen from 1 choice
usb 7-1: New USB device found, idVendor=147e, idProduct=2016
usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 7-1: Product: Fingerprint Sensor   
usb 7-1: Manufacturer: TouchStrip        
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
rtc_cmos 00:03: setting system clock to 2008-11-23 10:18:18 UTC (1227435498)
Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa5a0b1, caps: 0xa04713/0x0
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input0
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 340k freed
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C09:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID0]
input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C09:00/PNP0C0E:00/input/input4
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT BF7B01C0, 0297 (r1  PmRef  Cpu0Ist     3000 INTL 20051117)
Parsing all Control Methods:
Table [SSDT](id 0030) - 6 Objects with 0 Devices 4 Methods 0 Regions
ACPI: SSDT BF7B04F0, 0594 (r1  PmRef  Cpu0Cst     3001 INTL 20051117)
Parsing all Control Methods:
Table [SSDT](id 0031) - 1 Objects with 0 Devices 1 Methods 0 Regions
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:00: registered as cooling_device0
ACPI: SSDT BF7B00F0, 00C8 (r1  PmRef  Cpu1Ist     3000 INTL 20051117)
Parsing all Control Methods:
Table [SSDT](id 0035) - 4 Objects with 0 Devices 4 Methods 0 Regions
ACPI: SSDT BF7B0460, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20051117)
Parsing all Control Methods:
Table [SSDT](id 0036) - 1 Objects with 0 Devices 1 Methods 0 Regions
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI0007:01: registered as cooling_device1
Marking TSC unstable due to TSC halts in idle
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ADP1] (on-line)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (60 C)
acpi device:27: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:23/input/input6
atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
input: PC Speaker as /devices/platform/pcspkr/input/input7
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
HDA Intel 0000:00:1b.0: setting latency timer to 64
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
iwlagn: Copyright(c) 2003-2008 Intel Corporation
iwlagn 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
iwlagn 0000:02:00.0: setting latency timer to 64
iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels
iwlagn 0000:02:00.0: PCI INT A disabled
phy0: Selected rate control algorithm 'iwl-agn-rs'
EXT3 FS on sda2, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.9)
Clocksource tsc unstable (delta = -95387472 ns)
r8169: eth0: link up
r8169: eth0: link up
iwlagn 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x100102, writing 0x100106)
firmware: requesting iwlwifi-4965-2.ucode
iwlagn: Radio disabled by HW RF Kill switch
Adding 3068404k swap on /dev/sda4.  Priority:-1 extents:1 across:3068404k
 CIFS VFS: Error connecting to IPv4 socket. Aborting operation
 CIFS VFS: cifs_mount failed w/return code = -111
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): wlan0: link is not ready
eth0: no IPv6 routers present
atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm:i915_getparam] *ERROR* Unknown parameter 5
atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus
reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining
X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus
reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining
X:3889 freeing invalid memtype d0000000-e0000000
X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus
reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining
X:3890 freeing invalid memtype d0000000-e0000000
X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus
reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining
X:3931 freeing invalid memtype d0000000-e0000000
X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus
reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining
X:3933 freeing invalid memtype d0000000-e0000000
X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus
reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining
X:3935 freeing invalid memtype d0000000-e0000000
atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e077 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e078 <keycode>' to make it known.