Linux version 2.6.27-gentoo-r4 (root@looptop) (gcc version 4.3.2 (Gentoo 4.3.2 p1.0) ) #1 SMP PREEMPT Sat Nov 22 14:46:17 IST 2008 Command line: video=uvesafb:1280x800-32,mtrr:3 root=/dev/sda2 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ac00 (usable) BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000bf7a0000 (usable) BIOS-e820: 00000000bf7a0000 - 00000000bf7ae000 (ACPI data) BIOS-e820: 00000000bf7ae000 - 00000000bf7f0000 (ACPI NVS) BIOS-e820: 00000000bf7f0000 - 00000000bf800000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) DMI present. AMI BIOS detected: BIOS may corrupt low RAM, working it around. last_pfn = 0xbf7a0 max_arch_pfn = 0x3ffffffff x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 init_memory_mapping 0000000000 - 00bf600000 page 2M 00bf600000 - 00bf7a0000 page 4k kernel direct mapping tables up to bf7a0000 @ 10000-15000 last_map_addr: bf7a0000 end: bf7a0000 ACPI: RSDP 000F8CA0, 0014 (r0 ACPIAM) ACPI: RSDT BF7A0000, 0044 (r1 040808 RSDT1328 20080408 MSFT 97) ACPI: FACP BF7A0200, 0084 (r2 040808 FACP1328 20080408 MSFT 97) ACPI: DSDT BF7A05B0, 5ACD (r1 A1221 A1221000 0 INTL 20051117) ACPI: FACS BF7AE000, 0040 ACPI: APIC BF7A0390, 005C (r1 040808 APIC1328 20080408 MSFT 97) ACPI: MCFG BF7A03F0, 003C (r1 040808 OEMMCFG 20080408 MSFT 97) ACPI: SLIC BF7A0430, 0176 (r1 040808 SLIC1328 20080408 MSFT 97) ACPI: OEMB BF7AE040, 0071 (r1 040808 OEMB1328 20080408 MSFT 97) ACPI: HPET BF7A6080, 0038 (r1 040808 OEMHPET 20080408 MSFT 97) ACPI: GSCI BF7AE0C0, 2024 (r1 040808 GMCHSCI 20080408 MSFT 97) ACPI: SSDT BF7B0A90, 04F0 (r1 PmRef CpuPm 3000 INTL 20051117) (5 early reservations) ==> bootmem [0000000000 - 00bf7a0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 00006f9d58] TEXT DATA BSS ==> [0000200000 - 00006f9d58] #3 [000009ac00 - 0000100000] BIOS reserved ==> [000009ac00 - 0000100000] #4 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000] [ffffe20000000000-ffffe200029fffff] PMD -> [ffff880001200000-ffff880003bfffff] on node 0 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x0000009a 0: 0x00000100 -> 0x000bf7a0 On node 0 totalpages: 784170 DMA zone: 2542 pages, LIFO batch:0 DMA32 zone: 769525 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat ACPI: HPET id: 0x8086a201 base: 0xfed00000 SMP: Allowing 2 CPUs, 0 hotplug CPUs PM: Registered nosave memory: 000000000009a000 - 000000000009b000 PM: Registered nosave memory: 000000000009b000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 Allocating PCI resources starting at c0000000 (gap: bf800000:3f600000) PERCPU: Allocating 46212 bytes of per cpu data NR_CPUS: 8, nr_cpu_ids: 2, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 772067 Kernel command line: video=uvesafb:1280x800-32,mtrr:3 root=/dev/sda2 Initializing CPU#0 Preemptible RCU implementation. PID hash table entries: 4096 (order: 12, 32768 bytes) TSC: PIT calibration confirmed by PMTIMER. TSC: using PIT calibration value Detected 2194.476 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... No AGP bridge found Memory: 3081508k/3137152k available (3053k kernel code, 54596k reserved, 1177k data, 340k init) CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 hpet clockevent registered Calibrating delay loop (skipped), value calculated using timer frequency.. 4388.95 BogoMIPS (lpj=2194476) Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM2) using mwait in idle threads. ACPI: Core revision 20080609 Parsing all Control Methods: Table [DSDT](id 0001) - 899 Objects with 70 Devices 209 Methods 32 Regions Parsing all Control Methods: Table [SSDT](id 0002) - 15 Objects with 0 Devices 4 Methods 0 Regions tbxface-0596 [02] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [02] enable : Transition to ACPI mode successful ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping 0b Using local APIC timer interrupts. APIC timer calibration result 12468610 Detected 12.468 MHz APIC timer. Booting processor 1/1 ip 6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4388.77 BogoMIPS (lpj=2194387) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU1: Thermal monitoring enabled (TM2) x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping 0b checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs Total of 2 processors activated (8777.72 BogoMIPS). net_namespace: 1464 bytes NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 PCI: Not using MMCONFIG. PCI: Using configuration type 1 for base access evgpeblk-0957 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 ACPI: EC: Look up EC in DSDT Completing Region/Field/Buffer/Package initialization:.................................................................................................................................. Initialized 28/32 Regions 26/26 Fields 40/41 Buffers 36/36 Packages (923 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods: Executed 0 _INI methods requiring 0 _STA executions (examined 75 objects) evgpeblk-1054 [03] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 3 Runtime GPEs in this block ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 ACPI Error (evregion-0315): No handler for Region [EC__] (ffff8800bf0133a8) [EmbeddedControl] [20080609] ACPI Error (exfldio-0291): Region EmbeddedControl(3) has no handler [20080609] ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST ACPI Error (uteval-0232): Method execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST ACPI Error (evregion-0315): No handler for Region [EC__] (ffff8800bf0133a8) [EmbeddedControl] [20080609] ACPI Error (exfldio-0291): Region EmbeddedControl(3) has no handler [20080609] ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST ACPI Error (uteval-0232): Method execution failed [\_SB_.PCI0.SBRG.EC__.BAT1._STA] (Node ffff8800bf014dc0), AE_NOT_EXIST PCI: MCFG area at e0000000 reserved in ACPI motherboard resources PCI: Using MMCONFIG at e0000000 - efffffff ACPI: EC: non-query interrupt received, switching to interrupt mode ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62 ACPI: EC: driver started in interrupt mode ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: 0000:00:02.0 reg 10 64bit mmio: [fda00000, fdafffff] PCI: 0000:00:02.0 reg 18 64bit mmio: [d0000000, dfffffff] PCI: 0000:00:02.0 reg 20 io port: [b480, b487] PCI: 0000:00:02.1 reg 10 64bit mmio: [fdb00000, fdbfffff] PCI: 0000:00:1a.0 reg 20 io port: [b800, b81f] PCI: 0000:00:1a.1 reg 20 io port: [b880, b89f] PCI: 0000:00:1a.7 reg 10 32bit mmio: [fdcff000, fdcff3ff] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold pci 0000:00:1a.7: PME# disabled PCI: 0000:00:1b.0 reg 10 64bit mmio: [fdcf8000, fdcfbfff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold pci 0000:00:1c.1: PME# disabled pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold pci 0000:00:1c.2: PME# disabled PCI: 0000:00:1d.0 reg 20 io port: [bc00, bc1f] PCI: 0000:00:1d.1 reg 20 io port: [c000, c01f] PCI: 0000:00:1d.2 reg 20 io port: [c080, c09f] PCI: 0000:00:1d.7 reg 10 32bit mmio: [fdcff400, fdcff7ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO PCI: 0000:00:1f.1 reg 10 io port: [0, 7] PCI: 0000:00:1f.1 reg 14 io port: [0, 3] PCI: 0000:00:1f.1 reg 18 io port: [8f0, 8f7] PCI: 0000:00:1f.1 reg 1c io port: [8f8, 8fb] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf] PCI: 0000:00:1f.2 reg 10 io port: [cc00, cc07] PCI: 0000:00:1f.2 reg 14 io port: [c880, c883] PCI: 0000:00:1f.2 reg 18 io port: [c800, c807] PCI: 0000:00:1f.2 reg 1c io port: [c480, c483] PCI: 0000:00:1f.2 reg 20 io port: [c400, c41f] PCI: 0000:00:1f.2 reg 24 32bit mmio: [fdcff800, fdcfffff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled PCI: bridge 0000:00:1c.0 io port: [e000, efff] PCI: bridge 0000:00:1c.0 32bit mmio: [fe000000, febfffff] PCI: bridge 0000:00:1c.0 64bit mmio pref: [fa000000, fcffffff] PCI: 0000:03:00.0 reg 10 io port: [d800, d8ff] PCI: 0000:03:00.0 reg 18 64bit mmio: [fdfff000, fdffffff] PCI: 0000:03:00.0 reg 30 32bit mmio: [fdfc0000, fdfdffff] pci 0000:03:00.0: supports D1 pci 0000:03:00.0: supports D2 pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold pci 0000:03:00.0: PME# disabled PCI: bridge 0000:00:1c.1 io port: [d000, dfff] PCI: bridge 0000:00:1c.1 32bit mmio: [fdf00000, fdffffff] PCI: 0000:02:00.0 reg 10 64bit mmio: [fdefe000, fdefffff] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold pci 0000:02:00.0: PME# disabled PCI: bridge 0000:00:1c.2 32bit mmio: [fde00000, fdefffff] PCI: 0000:01:04.0 reg 10 32bit mmio: [fddff000, fddff07f] pci 0000:01:04.0: supports D1 pci 0000:01:04.0: supports D2 pci 0000:01:04.0: PME# supported from D0 D1 D2 D3hot pci 0000:01:04.0: PME# disabled PCI: 0000:01:04.1 reg 10 32bit mmio: [fddff400, fddff4ff] pci 0000:01:04.1: supports D1 pci 0000:01:04.1: supports D2 pci 0000:01:04.1: PME# supported from D0 D1 D2 D3hot pci 0000:01:04.1: PME# disabled PCI: 0000:01:04.2 reg 10 32bit mmio: [fddff800, fddff87f] pci 0000:01:04.2: supports D1 pci 0000:01:04.2: supports D2 pci 0000:01:04.2: PME# supported from D0 D1 D2 D3hot pci 0000:01:04.2: PME# disabled PCI: 0000:01:04.3 reg 10 32bit mmio: [fddffc00, fddffcff] pci 0000:01:04.3: supports D1 pci 0000:01:04.3: supports D2 pci 0000:01:04.3: PME# supported from D0 D1 D2 D3hot pci 0000:01:04.3: PME# disabled pci 0000:00:1e.0: transparent bridge PCI: bridge 0000:00:1e.0 32bit mmio: [fdd00000, fddfffff] bus 00 -> node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 *7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 *15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI-GART: No AMD northbridge found. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz ACPI: RTC can wake from S4 system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved system 00:08: ioport range 0x400-0x41f has been reserved system 00:08: ioport range 0x4d0-0x4d1 has been reserved system 00:08: ioport range 0x800-0x87f has been reserved system 00:08: ioport range 0x500-0x53f has been reserved system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved system 00:08: iomem range 0xfed40000-0xfed8ffff has been reserved system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved system 00:0c: iomem range 0x0-0x9ffff could not be reserved system 00:0c: iomem range 0xc0000-0xcffff has been reserved system 00:0c: iomem range 0xe0000-0xfffff could not be reserved system 00:0c: iomem range 0x100000-0xbf7fffff could not be reserved system 00:0c: iomem range 0xfed90000-0xffffffff could not be reserved pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 pci 0000:00:1c.0: IO window: 0xe000-0xefff pci 0000:00:1c.0: MEM window: 0xfe000000-0xfebfffff pci 0000:00:1c.0: PREFETCH window: 0x000000fa000000-0x000000fcffffff pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03 pci 0000:00:1c.1: IO window: 0xd000-0xdfff pci 0000:00:1c.1: MEM window: 0xfdf00000-0xfdffffff pci 0000:00:1c.1: PREFETCH window: disabled pci 0000:00:1c.2: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.2: IO window: disabled pci 0000:00:1c.2: MEM window: 0xfde00000-0xfdefffff pci 0000:00:1c.2: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: 0xfdd00000-0xfddfffff pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 pci 0000:00:1c.2: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 04 index 0 io port: [e000, efff] bus: 04 index 1 mmio: [fe000000, febfffff] bus: 04 index 2 mmio: [fa000000, fcffffff] bus: 04 index 3 mmio: [0, 0] bus: 03 index 0 io port: [d000, dfff] bus: 03 index 1 mmio: [fdf00000, fdffffff] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 02 index 0 mmio: [0, 0] bus: 02 index 1 mmio: [fde00000, fdefffff] bus: 02 index 2 mmio: [0, 0] bus: 02 index 3 mmio: [0, 0] bus: 01 index 0 mmio: [0, 0] bus: 01 index 1 mmio: [fdd00000, fddfffff] bus: 01 index 2 mmio: [0, 0] bus: 01 index 3 io port: [0, ffff] bus: 01 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 IA-32 Microcode Update Driver: v1.14a VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) msgmni has been set to 6019 io scheduler noop registered io scheduler cfq registered (default) pci 0000:00:02.0: Boot video device pcieport-driver 0000:00:1c.0: setting latency timer to 64 pcieport-driver 0000:00:1c.0: found MSI capability pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pci_express 0000:00:1c.0:pcie03: allocate port service pcieport-driver 0000:00:1c.1: setting latency timer to 64 pcieport-driver 0000:00:1c.1: found MSI capability pci_express 0000:00:1c.1:pcie00: allocate port service pci_express 0000:00:1c.1:pcie02: allocate port service pci_express 0000:00:1c.1:pcie03: allocate port service pcieport-driver 0000:00:1c.2: setting latency timer to 64 pcieport-driver 0000:00:1c.2: found MSI capability pci_express 0000:00:1c.2:pcie00: allocate port service pci_express 0000:00:1c.2:pcie02: allocate port service pci_express 0000:00:1c.2:pcie03: allocate port service hpet_resources: 0xfed00000 is busy Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 965GM Chipset agpgart-intel 0000:00:00.0: detected 7676K stolen memory agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 uvesafb: Intel Corporation, Intel(r)GM965/PM965/GL960 Graphics Controller, Hardware Version 0.0, OEM: Intel(r)GM965/PM965/GL960 Graphics Chip Accelerated VGA BIOS, VBE v3.0 uvesafb: VBIOS/hardware supports DDC2 transfers uvesafb: monitor limits: vf = 60 Hz, hf = 49 kHz, clk = 68 MHz uvesafb: scrolling: redraw Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 Console: switching to colour frame buffer device 160x50 uvesafb: framebuffer at 0xd0000000, mapped to 0xffffc20010300000, using 7616k, total 7616k fb0: VESA VGA frame buffer device r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 r8169 0000:03:00.0: setting latency timer to 64 eth0: RTL8168b/8111b at 0xffffc2000002c000, 00:1d:92:51:62:f7, XID 38000000 IRQ 508 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 ahci 0000:00:1f.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part ems ahci 0000:00:1f.2: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci ata1: SATA max UDMA/133 abar m2048@0xfdcff800 port 0xfdcff900 irq 507 ata2: SATA max UDMA/133 abar m2048@0xfdcff800 port 0xfdcff980 irq 507 ata3: SATA max UDMA/133 abar m2048@0xfdcff800 port 0xfdcffa00 irq 507 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: TOSHIBA MK1646GSX, LB111A, max UDMA/100 ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/100 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1646GS LB11 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi3 : ata_piix scsi4 : ata_piix ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WA03, max UDMA/33 ata4.00: configured for UDMA/33 ata5: port disabled. ignoring. isa bounce pool size: 16 pages scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WA03 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 3:0:0:0: Attached scsi CD-ROM sr0 sr 3:0:0:0: Attached scsi generic sg1 type 5 ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 ehci_hcd 0000:00:1a.7: setting latency timer to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdcff000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.27-gentoo-r4 ehci_hcd usb usb1: SerialNumber: 0000:00:1a.7 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdcff400 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.27-gentoo-r4 ehci_hcd usb usb2: SerialNumber: 0000:00:1d.7 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1a.0: setting latency timer to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000b800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd usb usb3: SerialNumber: 0000:00:1a.0 uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:1a.1: setting latency timer to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000b880 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd usb usb4: SerialNumber: 0000:00:1a.1 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000bc00 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd usb usb5: SerialNumber: 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c000 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: UHCI Host Controller usb usb6: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd usb usb6: SerialNumber: 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c080 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb7: Product: UHCI Host Controller usb usb7: Manufacturer: Linux 2.6.27-gentoo-r4 uhci_hcd usb usb7: SerialNumber: 0000:00:1d.2 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k, hpet irqs device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu usb 7-1: new full speed USB device using uhci_hcd and address 2 usb 7-1: configuration #1 chosen from 1 choice usb 7-1: New USB device found, idVendor=147e, idProduct=2016 usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 7-1: Product: Fingerprint Sensor usb 7-1: Manufacturer: TouchStrip usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 rtc_cmos 00:03: setting system clock to 2008-11-23 10:18:18 UTC (1227435498) Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa5a0b1, caps: 0xa04713/0x0 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input0 input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 340k freed input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C09:00/PNP0C0D:00/input/input3 ACPI: Lid Switch [LID0] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C09:00/PNP0C0E:00/input/input4 ACPI: Sleep Button (CM) [SLPB] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5 ACPI: Power Button (CM) [PWRB] ACPI: SSDT BF7B01C0, 0297 (r1 PmRef Cpu0Ist 3000 INTL 20051117) Parsing all Control Methods: Table [SSDT](id 0030) - 6 Objects with 0 Devices 4 Methods 0 Regions ACPI: SSDT BF7B04F0, 0594 (r1 PmRef Cpu0Cst 3001 INTL 20051117) Parsing all Control Methods: Table [SSDT](id 0031) - 1 Objects with 0 Devices 1 Methods 0 Regions Monitor-Mwait will be used to enter C-1 state Monitor-Mwait will be used to enter C-2 state Monitor-Mwait will be used to enter C-3 state ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) processor ACPI0007:00: registered as cooling_device0 ACPI: SSDT BF7B00F0, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20051117) Parsing all Control Methods: Table [SSDT](id 0035) - 4 Objects with 0 Devices 4 Methods 0 Regions ACPI: SSDT BF7B0460, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20051117) Parsing all Control Methods: Table [SSDT](id 0036) - 1 Objects with 0 Devices 1 Methods 0 Regions ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) processor ACPI0007:01: registered as cooling_device1 Marking TSC unstable due to TSC halts in idle ACPI: Battery Slot [BAT1] (battery present) ACPI: AC Adapter [ADP1] (on-line) thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [THRM] (60 C) acpi device:27: registered as cooling_device2 input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:23/input/input6 atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) input: PC Speaker as /devices/platform/pcspkr/input/input7 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 HDA Intel 0000:00:1b.0: setting latency timer to 64 iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks iwlagn: Copyright(c) 2003-2008 Intel Corporation iwlagn 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 iwlagn 0000:02:00.0: setting latency timer to 64 iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:02:00.0: PCI INT A disabled phy0: Selected rate control algorithm 'iwl-agn-rs' EXT3 FS on sda2, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. fuse init (API version 7.9) Clocksource tsc unstable (delta = -95387472 ns) r8169: eth0: link up r8169: eth0: link up iwlagn 0000:02:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x100102, writing 0x100106) firmware: requesting iwlwifi-4965-2.ucode iwlagn: Radio disabled by HW RF Kill switch Adding 3068404k swap on /dev/sda4. Priority:-1 extents:1 across:3068404k CIFS VFS: Error connecting to IPv4 socket. Aborting operation CIFS VFS: cifs_mount failed w/return code = -111 NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): wlan0: link is not ready eth0: no IPv6 routers present atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. [drm] Initialized drm 1.1.0 20060810 pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:02.0: setting latency timer to 64 [drm] Initialized i915 1.6.0 20060119 on minor 0 [drm:i915_getparam] *ERROR* Unknown parameter 5 atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining X:3889 freeing invalid memtype d0000000-e0000000 X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining X:3890 freeing invalid memtype d0000000-e0000000 X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining X:3931 freeing invalid memtype d0000000-e0000000 X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining X:3933 freeing invalid memtype d0000000-e0000000 X:3858 conflicting memory types d0000000-e0000000 write-combining<->uncached-minus reserve_memtype failed 0xd0000000-0xe0000000, track write-combining, req write-combining X:3935 freeing invalid memtype d0000000-e0000000 atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf7 on isa0060/serio0). atkbd.c: Use 'setkeycodes e077 ' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf8 on isa0060/serio0). atkbd.c: Use 'setkeycodes e078 ' to make it known.