# Copyright 1999-2008 Gentoo Foundation
# Distributed under the terms of the GNU General Public License v2
# $Header: $

# 2008 Nuno Sucena Almeida
#

inherit eutils

MY_PN="boost-numeric-bindings"
DESCRIPTION="Boost UBLAS numeric bindings"
HOMEPAGE="http://mathema.tician.de/software/${MY_PN}"
#SRC_URI="http://mathema.tician.de/news.tiker.net/download/software/${MY_PN}/${MY_PN}-${PV}.tar.gz"
SRC_URI="http://aeminium.org/slug/software/gentoo/${MY_PN}/${MY_PN}-${PV}.tar.gz"

LICENSE="Boost-1.0"
SLOT="0"
KEYWORDS="~x86 ~amd64"
IUSE=""

DEPEND="boost? ( >=dev-libs/boost-1.35.0 )"

RDEPEND="${DEPEND}"

#S="${WORKDIR}/${MY_PN}"

src_compile() {
	# Most open-source packages use GNU autoconf for configuration.
	# The quickest (and preferred) way of running configure is:
	econf || die "econf failed"
	#
	# You could use something similar to the following lines to
	# configure your package before compilation.  The "|| die" portion
	# at the end will stop the build process if the command fails.
	# You should use this at the end of critical commands in the build
	# process.  (Hint: Most commands are critical, that is, the build
	# process should abort if they aren't successful.)
	#./configure \
	#	--host=${CHOST} \
	#	--prefix=/usr \
	#	--infodir=/usr/share/info \
	#	--mandir=/usr/share/man || die "./configure failed"
	# Note the use of --infodir and --mandir, above. This is to make
	# this package FHS 2.2-compliant.  For more information, see
	#   http://www.pathname.com/fhs/
	#./configure \
	#33	--prefix=/usr || die "./configure failed"

	# emake (previously known as pmake) is a script that calls the
	# standard GNU make with parallel building options for speedier
	# builds (especially on SMP systems).  Try emake first.  It might
	# not work for some packages, because some makefiles have bugs
	# related to parallelism, in these cases, use emake -j1 to limit
	# make to a single process.  The -j1 is a visual clue to others
	# that the makefiles have bugs that have been worked around.
	emake || die "emake failed"
}

src_install() {
	# You must *personally verify* that this trick doesn't install
	# anything outside of DESTDIR; do this by reading and
	# understanding the install part of the Makefiles.
	# This is the preferred way to install.
	emake DESTDIR="${D}" install || die "emake install failed"

	# When you hit a failure with emake, do not just use make. It is
	# better to fix the Makefiles to allow proper parallelization.
	# If you fail with that, use "emake -j1", it's still better than make.

	# For Makefiles that don't make proper use of DESTDIR, setting
	# prefix is often an alternative.  However if you do this, then
	# you also need to specify mandir and infodir, since they were
	# passed to ./configure as absolute paths (overriding the prefix
	# setting).
	#emake \
	#	prefix="${D}"/usr \
	#	mandir="${D}"/usr/share/man \
	#	infodir="${D}"/usr/share/info \
	#	libdir="${D}"/usr/$(get_libdir) \
	#	install || die "emake install failed"
	# Again, verify the Makefiles!  We don't want anything falling
	# outside of ${D}.

	# The portage shortcut to the above command is simply:
	#
	#einstall || die "einstall failed"
}