dmesg output

dmesg (text/plain), 26.74 KB, created by Pierre AUSSAGUEL on 2008-05-09 19:31:26 UTC

Linux version 2.6.24-tuxonice-r4 (root@core2) (gcc version 4.1.2 (Gentoo 4.1.2)) #1 SMP PREEMPT Wed May 7 23:01:20 CEST 2008
Command line: root=/dev/sda2 quiet CONSOLE=/dev/tty1 video=uvesafb:1024x768-24,ywrap,mtrr:3 splash=silent,theme:gentoo
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
 BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
 BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
 BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
 BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 524000) 1 entries of 256 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F6EF0, 0014 (r0 GBT   )
ACPI: RSDT 7FEE3040, 003C (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: FACP 7FEE30C0, 0074 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: DSDT 7FEE3180, 49F4 (r1 GBT    GBTUACPI     1000 MSFT  100000C)
ACPI: FACS 7FEE0000, 0040
ACPI: HPET 7FEE7CC0, 0038 (r1 GBT    GBTUACPI 42302E31 GBTU       98)
ACPI: MCFG 7FEE7D40, 003C (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: APIC 7FEE7BC0, 0084 (r1 GBT    GBTUACPI 42302E31 GBTU  1010101)
ACPI: SSDT 7FEE7DC0, 015C (r1  PmRef  Cpu0Ist     3000 INTL 20040311)
ACPI: SSDT 7FEE8250, 0275 (r1  PmRef    CpuPm     3000 INTL 20040311)
Entering add_active_range(0, 0, 158) 0 entries of 256 used
Entering add_active_range(0, 256, 524000) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      158
    0:      256 ->   524000
On node 0 totalpages: 523902
  DMA zone: 56 pages used for memmap
  DMA zone: 1398 pages reserved
  DMA zone: 2544 pages, LIFO batch:0
  DMA32 zone: 7108 pages used for memmap
  DMA32 zone: 512796 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7ff00000:70100000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 29024 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 515340
Kernel command line: root=/dev/sda2 quiet CONSOLE=/dev/tty1 video=uvesafb:1024x768-24,ywrap,mtrr:3 splash=silent,theme:gentoo
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
hpet clockevent registered
TSC calibrated against HPET
time.c: Detected 1866.666 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
Memory: 2056864k/2096000k available (3353k kernel code, 38320k reserved, 1488k data, 296k init)
Calibrating delay using timer specific routine.. 3735.48 BogoMIPS (lpj=1867742)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 16666664
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3733.23 BogoMIPS (lpj=1866619)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU          6300  @ 1.86GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at f0000000 - f3ffffff
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnpacpi: exceeded the max number of mem resources: 12
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-GART: No AMD northbridge found.
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x290-0x29f has been reserved
system 00:01: ioport range 0x800-0x87f has been reserved
system 00:01: ioport range 0x290-0x294 has been reserved
system 00:01: ioport range 0x880-0x88f has been reserved
system 00:0a: ioport range 0x400-0x4bf could not be reserved
system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved
system 00:0c: iomem range 0xd5000-0xd7fff has been reserved
system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved
system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
system 00:0c: iomem range 0x7fee0000-0x7fefffff could not be reserved
system 00:0c: iomem range 0x0-0x9ffff could not be reserved
system 00:0c: iomem range 0x100000-0x7fedffff could not be reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0c: iomem range 0xfed10000-0xfed1dfff has been reserved
system 00:0c: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0c: iomem range 0xffb00000-0xffb7ffff has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: f4000000-f6ffffff
  PREFETCH window: e0000000-efffffff
PCI: Bridge: 0000:00:1c.0
  IO window: 8000-8fff
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
  IO window: 9000-9fff
  MEM window: f7000000-f8ffffff
  PREFETCH window: 80000000-800fffff
PCI: Bridge: 0000:00:1c.5
  IO window: a000-bfff
  MEM window: f9000000-f90fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: f9100000-f91fffff
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 827k freed
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
Allocate Port Service[0000:00:1c.4:pcie03]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
Allocate Port Service[0000:00:1c.5:pcie03]
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
platform pc8736x_gpio.0: NatSemi pc8736x GPIO Driver Initializing
platform pc8736x_gpio.0: no device found
nsc_gpio initializing
Linux agpgart interface v0.102
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
uvesafb: NVIDIA Corporation, G72 Board - p381n5  , Chip Rev   , OEM: NVIDIA, VBE v3.0
uvesafb: VBIOS/hardware doesn't support DDC transfers
uvesafb: no monitor limits have been set, default refresh rate will be used
uvesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
uvesafb: framebuffer at 0xe0000000, mapped to 0xffffc20004100000, using 24576k, total 131072k
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /devices/virtual/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: SSDT 7FEE81C0, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20040311)
ACPI: Processor [CPU1] (supports 2 throttling states)
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:03:00.0 to 64
sky2 0000:03:00.0: v1.20 addr 0xf8000000 irq 16 Yukon-EC (0xb6) rev 2
sky2 eth0: addr 00:16:e6:5e:a8:e2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[e-mail]>
Linux video capture interface: v2.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
JMB: IDE controller (0x197b:0x2363 rev 0x02) at  PCI slot 0000:04:00.1
ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 18 (level, low) -> IRQ 18
JMB: 100% native mode on irq 18
    ide0: BM-DMA at 0xb000-0xb007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xb008-0xb00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: QUANTUM FIREBALLlct08 08, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: drive side 80-wire cable detection failed, limiting max speed to UDMA33
hda: UDMA/33 mode selected
ide0 at 0xa000-0xa007,0xa402 on irq 18
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 16514064 sectors (8455 MB) w/418KiB Cache, CHS=16383/16/63
hda: cache flushes not supported
 hda: hda1
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part 
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 19
ata2: SATA max UDMA/133 abar m2048@0xf9206000 port 0xf9206180 irq 19
ata3: SATA max UDMA/133 abar m2048@0xf9206000 port 0xf9206200 irq 19
ata4: SATA max UDMA/133 abar m2048@0xf9206000 port 0xf9206280 irq 19
ata5: SATA max UDMA/133 abar m2048@0xf9206000 port 0xf9206300 irq 19
ata6: SATA max UDMA/133 abar m2048@0xf9206000 port 0xf9206380 irq 19
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: HPA detected: current 145223999, native 145226112
ata1.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata1.00: 145223999 sectors, multi 0: LBA48 NCQ (not used)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: TSSTcorpCD/DVDW SH-S183A, SB02, max UDMA/33, ATAPI AN
ata3.00: applying bridge limits
ata3.00: configured for UDMA/33
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 145223999 512-byte hardware sectors (74355 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 145223999 512-byte hardware sectors (74355 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 2:0:0:0: CD-ROM            TSSTcorp CD/DVDW SH-S183A SB02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr 2:0:0:0: Attached scsi generic sg1 type 5
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:04:00.0 to 64
scsi6 : ahci
scsi7 : ahci
ata7: SATA max UDMA/133 abar m8192@0xf9000000 port 0xf9000100 irq 17
ata8: SATA max UDMA/133 abar m8192@0xf9000000 port 0xf9000180 irq 17
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9205000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9204000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000c400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000cc00
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d000
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-2: new low speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 7-1: new low speed USB device using uhci_hcd and address 2
usb 7-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12
PNP: PS/2 controller doesn't have KBD irq; using default 1
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PS2++ Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input2
coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
usbcore: registered new interface driver hiddev
input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input3
input,hidraw0: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-0000:00:1a.0-2
input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.1/input/input4
input,hiddev96,hidraw1: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:1a.0-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 2007 UTC).
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ALSA device list:
  #0: HDA Intel at 0xf9200000 irq 22
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Replacing swsusp.
TuxOnIce: Normal swapspace found.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 296k freed
ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[f9104000-f91047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  169.09  Fri Jan 11 14:04:37 PST 2008
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0016e60000b7a312]
EXT3 FS on sda2, internal journal
i2c /dev entries driver
it87: Found IT8718F chip at 0x290, revision 1
it87: in3 is VCC (+5V)
ieee1394: raw1394: /dev/raw1394 device initialized
video1394: Installed video1394 module
Adding 4192924k swap on /dev/sda1.  Priority:-1 extents:1 across:4192924k
sky2 eth0: enabling interface
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control rx
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: disabling interface
sky2 eth0: enabling interface
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: disabling interface
sky2 eth0: enabling interface
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
sky2 eth0: Link is down.
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110
usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd newhidups rqt 128 rq 6 len 255 ret -110

And after having launched K3B, it adds :

ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 8 in
         cdb ac 00 00 00 00 00 00 00  00 01 03 00 00 00 00 00
         res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata3.00: status: { DRDY }
ata3: soft resetting link
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5)
ata3.00: revalidation failed (errno=-5)
ata3: failed to recover some devices, retrying in 5 secs
ata3: hard resetting link
ata3: port is slow to respond, please be patient (Status 0x80)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: port is slow to respond, please be patient (Status 0x80)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: port is slow to respond, please be patient (Status 0x80)
ata3: COMRESET failed (errno=-16)
ata3: limiting SATA link speed to 1.5 Gbps
ata3: hard resetting link
ata3: COMRESET failed (errno=-16)
ata3: reset failed, giving up
ata3.00: disabled
ata3: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xa frozen t4
ata3: SError: { PHYRdyChg CommWake DevExch }
ata3: hard resetting link
ata3: port is slow to respond, please be patient (Status 0x80)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: port is slow to respond, please be patient (Status 0x80)
ata3: COMRESET failed (errno=-16)
ata3: hard resetting link
ata3: port is slow to respond, please be patient (Status 0x80)
ata3: COMRESET failed (errno=-16)
ata3: limiting SATA link speed to 1.5 Gbps
ata3: hard resetting link
ata3: COMRESET failed (errno=-16)
ata3: reset failed, giving up
sr 2:0:0:0: rejecting I/O to offline device
ata3: EH complete
ata3.00: detaching (SCSI 2:0:0:0)
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device
scsi 2:0:0:0: rejecting I/O to dead device