dmesg

dmesg (text/plain), 25.52 KB, created by VPN-User on 2007-04-01 19:01:11 UTC

Linux version 2.6.19-gentoo-r5 (root@kik-server) (gcc-Version 4.1.1 (Gentoo 4.1.1-r3)) #3 SMP Sat Mar 31 17:04:48 CEST 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003efc0000 (usable)
 BIOS-e820: 000000003efc0000 - 000000003efce000 (ACPI data)
 BIOS-e820: 000000003efce000 - 000000003eff0000 (ACPI NVS)
 BIOS-e820: 000000003eff0000 - 000000003f000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 229376) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
early_node_map[1] active PFN ranges
    0:        0 ->   229376
On node 0 totalpages: 229376
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM                                ) @ 0x000fbab0
ACPI: XSDT (v001 A M I  OEMXSDT  0x09000606 MSFT 0x00000097) @ 0x3efc0100
ACPI: FADT (v003 A M I  OEMFACP  0x09000606 MSFT 0x00000097) @ 0x3efc0290
ACPI: MADT (v001 A M I  OEMAPIC  0x09000606 MSFT 0x00000097) @ 0x3efc0390
ACPI: MCFG (v001 A M I  OEMMCFG  0x09000606 MSFT 0x00000097) @ 0x3efc0400
ACPI: OEMB (v001 A M I  AMI_OEM  0x09000606 MSFT 0x00000097) @ 0x3efce040
ACPI: SSDT (v001 A M I  POWERNOW 0x00000001 AMD  0x00000001) @ 0x3efc5300
ACPI: DSDT (v001  A0557 A0557000 0x00000000 INTL 0x02002026) @ 0x00000000
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x508
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 0 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f000000:bfc00000)
Detected 2009.212 MHz processor.
Built 1 zonelists.  Total pages: 227584
Kernel command line: auto BOOT_IMAGE=Gentoo root=902
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 905492k/917504k available (2299k kernel code, 11604k reserved, 791k data, 232k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffb7000 - 0xfffff000   ( 288 kB)
    vmalloc : 0xf8800000 - 0xfffb5000   ( 119 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc040c000 - 0xc0446000   ( 232 kB)
      .data : 0xc033ef06 - 0xc0404bd4   ( 791 kB)
      .text : 0xc0100000 - 0xc033ef06   (2299 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4022.57 BogoMIPS (lpj=8045152)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 0(2) -> Core 0
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4018.51 BogoMIPS (lpj=8037033)
CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU 1(2) -> Core 1
CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ stepping 02
Total of 2 processors activated (8041.09 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs:
CPU#0 had 130 usecs TSC skew, fixed it up.
CPU#1 had -130 usecs TSC skew, fixed it up.
Brought up 2 CPUs
migration_cost=125
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:0d.0
PCI: Transparent bridge - 0000:00:04.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *11
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *10
ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15
ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *5
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
Generic PHY: Registered new driver
SCSI subsystem initialized
libata version 2.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:04.0
  IO window: e000-efff
  MEM window: dff00000-dfffffff
  PREFETCH window: 40000000-400fffff
PCI: Bridge: 0000:00:09.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1175361502.568:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered (default)
PCI: Setting latency timer of device 0000:00:09.0 to 64
pcie_portdrv_probe->Dev[03e8:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:09.0:pcie00]
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[03e9:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[03e9:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
lp: driver loaded but no devices found
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 10240k, total 16384k
vesafb: mode is 1280x1024x32, linelength=5120, pages=0
vesafb: protected mode interface info at c000:cf90
vesafb: pmi: set display start = c00ccfc6, set palette = c00cd030
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Marvell 88E1101: Registered new driver
Davicom DM9161E: Registered new driver
Davicom DM9131: Registered new driver
Cicada Cis8204: Registered new driver
Cicada Cis8201: Registered new driver
LXT970: Registered new driver
LXT971: Registered new driver
QS6612: Registered new driver
SMSC LAN83C185: Registered new driver
Vitesse VSC8244: Registered new driver
Fixed PHY: Registered new driver
device_bind_driver: device fixed@100:1 already bound
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP61: IDE controller at PCI slot 0000:00:06.0
NFORCE-MCP61: chipset revision 162
NFORCE-MCP61: not 100% native mode: will probe irqs later
NFORCE-MCP61: 0000:00:06.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4120B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sata_nv 0000:00:08.0: version 2.0
ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD082 bmdma 0xC880 irq 16
ata2: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC888 irq 16
scsi0 : sata_nv
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200YS-01P 21.0 PQ: 0 ANSI: 5
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access     ATA      WDC WD3200YS-01P 21.0 PQ: 0 ANSI: 5
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:08.1[B] -> Link [LSA1] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:08.1 to 64
ata3: SATA max UDMA/133 cmd 0xC800 ctl 0xC482 bmdma 0xC000 irq 17
ata4: SATA max UDMA/133 cmd 0xC400 ctl 0xC082 bmdma 0xC008 irq 17
scsi2 : sata_nv
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/133
scsi3 : sata_nv
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/1)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access     ATA      WDC WD3200YS-01P 21.0 PQ: 0 ANSI: 5
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3 sdc4
sd 2:0:0:0: Attached scsi disk sdc
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access     ATA      WDC WD3200YS-01P 21.0 PQ: 0 ANSI: 5
SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdd: 625142448 512-byte hdwr sectors (320073 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
 sdd: sdd1 sdd2 sdd3 sdd4
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg3 type 0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
input: AT Translated Set 2 keyboard as /class/input/input0
raid6: int32x1    793 MB/s
raid6: int32x2    832 MB/s
raid6: int32x4    702 MB/s
raid6: int32x8    545 MB/s
raid6: mmxx1     1643 MB/s
raid6: mmxx2     2981 MB/s
raid6: sse1x1    1609 MB/s
raid6: sse1x2    2685 MB/s
raid6: sse2x1    2717 MB/s
raid6: sse2x2    3772 MB/s
raid6: using algorithm sse2x2 (3772 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
   pIII_sse  :  6204.000 MB/sec
raid5: using function: pIII_sse (6204.000 MB/sec)
md: faulty personality registered for level -5
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: [e-mail]
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 4
Starting balanced_irq
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
Time: acpi_pm clocksource has been installed.
md: autorun ...
md: considering sdd4 ...
md:  adding sdd4 ...
md: sdd3 has different UUID to sdd4
md: sdd2 has different UUID to sdd4
md: sdd1 has different UUID to sdd4
md:  adding sdc4 ...
md: sdc3 has different UUID to sdd4
md: sdc2 has different UUID to sdd4
md: sdc1 has different UUID to sdd4
md:  adding sdb4 ...
md: sdb3 has different UUID to sdd4
md: sdb2 has different UUID to sdd4
md: sdb1 has different UUID to sdd4
md:  adding sda4 ...
md: sda3 has different UUID to sdd4
md: sda2 has different UUID to sdd4
md: sda1 has different UUID to sdd4
md: created md3
md: bind<sda4>
md: bind<sdb4>
md: bind<sdc4>
md: bind<sdd4>
md: running: <sdd4><sdc4><sdb4><sda4>
raid5: device sdd4 operational as raid disk 0
raid5: device sdc4 operational as raid disk 1
raid5: device sdb4 operational as raid disk 2
raid5: device sda4 operational as raid disk 3
raid5: allocated 4204kB for md3
raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:sdd4
 disk 1, o:1, dev:sdc4
 disk 2, o:1, dev:sdb4
 disk 3, o:1, dev:sda4
md: considering sdd3 ...
md:  adding sdd3 ...
md: sdd2 has different UUID to sdd3
md: sdd1 has different UUID to sdd3
md:  adding sdc3 ...
md: sdc2 has different UUID to sdd3
md: sdc1 has different UUID to sdd3
md:  adding sdb3 ...
md: sdb2 has different UUID to sdd3
md: sdb1 has different UUID to sdd3
md:  adding sda3 ...
md: sda2 has different UUID to sdd3
md: sda1 has different UUID to sdd3
md: created md2
md: bind<sda3>
md: bind<sdb3>
md: bind<sdc3>
md: bind<sdd3>
md: running: <sdd3><sdc3><sdb3><sda3>
raid5: device sdd3 operational as raid disk 0
raid5: device sdc3 operational as raid disk 1
raid5: device sdb3 operational as raid disk 2
raid5: device sda3 operational as raid disk 3
raid5: allocated 4204kB for md2
raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:sdd3
 disk 1, o:1, dev:sdc3
 disk 2, o:1, dev:sdb3
 disk 3, o:1, dev:sda3
md: considering sdd2 ...
md:  adding sdd2 ...
md: sdd1 has different UUID to sdd2
md:  adding sdc2 ...
md: sdc1 has different UUID to sdd2
md:  adding sdb2 ...
md: sdb1 has different UUID to sdd2
md:  adding sda2 ...
md: sda1 has different UUID to sdd2
md: created md1
md: bind<sda2>
md: bind<sdb2>
md: bind<sdc2>
md: bind<sdd2>
md: running: <sdd2><sdc2><sdb2><sda2>
raid5: device sdd2 operational as raid disk 0
raid5: device sdc2 operational as raid disk 1
raid5: device sdb2 operational as raid disk 2
raid5: device sda2 operational as raid disk 3
raid5: allocated 4204kB for md1
raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:sdd2
 disk 1, o:1, dev:sdc2
 disk 2, o:1, dev:sdb2
 disk 3, o:1, dev:sda2
md: considering sdd1 ...
md:  adding sdd1 ...
md:  adding sdc1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: running: <sdd1><sdc1><sdb1><sda1>
raid1: raid set md0 active with 4 out of 4 mirrors
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with journal data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 232k freed
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.57.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LMAC] -> GSI 21 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:07.0 to 64
forcedeth: using HIGHDMA
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Intel(R) PRO/1000 Network Driver - version 7.2.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.2.1)
ath_rate_sample: 1.2 (0.9.2.1)
ath_pci: 0.9.4.5 (0.9.2.1)
Linux agpgart interface v0.101 (c) Dave Jones
eth0: forcedeth.c: subsystem: 01043:8234 bound to 0000:00:07.0
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 19, io mem 0xdfefec00
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 16, io mem 0xdfeff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [LNKA] -> GSI 19 (level, low) -> IRQ 20
e1000: 0000:01:06.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:a2:a6:a1
usb 2-4: new low speed USB device using ohci_hcd and address 2
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKB] -> GSI 18 (level, low) -> IRQ 21
usb 2-4: configuration #1 chosen from 1 choice
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.9 phy 4.3 radio 4.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
usbcore: registered new interface driver hiddev
wifi0: Atheros 5212: mem=0xdff90000, irq=21
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:05.0[B] -> Link [LAZA] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:05.0 to 64
ACPI: PCI Interrupt Link [LMC9] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LMC9] -> GSI 21 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:0d.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module  1.0-9755  Mon Feb 26 23:21:15 PST 2007
hiddev96: USB HID v1.10 Device [American Power Conversion Back-UPS CS 350 FW:807.q5.I USB FW:q5] on usb-0000:00:02.0-4
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
EXT3 FS on md2, internal journal
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ processors (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0xc
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0xe
powernow-k8:    2 : fid 0x2 (1000 MHz), vid 0x12
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
SGI XFS with large block numbers, no debug enabled
Filesystem "md3": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md3
Ending clean XFS mount for filesystem: md3
Adding 770680k swap on /dev/md1.  Priority:-1 extents:1 across:770680k
eth0: no link during initialization.
process `named' is using obsolete setsockopt SO_BSDCOMPAT
it87: Found IT8712F chip at 0x290, revision 8
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
usb 2-3: new low speed USB device using ohci_hcd and address 3
usb 2-3: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-3
eth0: link up.
e1000: eth1: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
e1000: eth1: e1000_watchdog: NIC Link is Down
e1000: eth1: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
e1000: eth1: e1000_watchdog: NIC Link is Down
eth0: link down.
Bridge firewalling registered
drivers/usb/input/hid-core.c: ctrl urb status -62 received
eth0: link up.
eth0: link down.
eth0: link up.
eth0: link down.
eth0: link up.
eth0: link down.
eth0: link up.
eth0: link down.
eth0: link up.
eth0: link down.
eth0: link up.