Go to:
Gentoo Home
Documentation
Forums
Lists
Bugs
Planet
Store
Wiki
Get Gentoo!
Gentoo's Bugzilla – Attachment 74916 Details for
Bug 114551
typo in ppp0 section of net.example (sys-apps/baselayout-1.12.0_pre11-r3)
Home
|
New
–
[Ex]
|
Browse
|
Search
|
Privacy Policy
|
[?]
|
Reports
|
Requests
|
Help
|
New Account
|
Log In
[x]
|
Forgot Password
Login:
[x]
proposed ppp section of net.example
net.example (text/plain), 3.95 KB, created by
Alin Năstac (RETIRED)
on 2005-12-17 01:08:14 UTC
(
hide
)
Description:
proposed ppp section of net.example
Filename:
MIME Type:
Creator:
Alin Năstac (RETIRED)
Created:
2005-12-17 01:08:14 UTC
Size:
3.95 KB
patch
obsolete
>#----------------------------------------------------------------------------- ># PPP ># For PPP support, emerge net-dialup/ppp ># PPP is used for most dialup connections, including ADSL. ># The older ADSL module is documented below, but you are encouraged to try ># this module first. ># ># You need to create the PPP net script yourself. Make it like so >#cd /etc/init.d >#ln -s net.lo net.ppp0 ># ># Configure the interface to use the ppp module >#config_ppp0=( "ppp" ) ># ># Each PPP interface requires an interface to use for sending/receiving PPP frames >#link_ppp0="/dev/ttyS0" # Most PPP links will use a serial port >#link_ppp0="eth0" # PPPoE requires an ethernet interface >#link_ppp0="/dev/null" # PPPoA and ISDN links should have this >#link_ppp0="pty 'your_link_command'" # PPP links over ssh,rsh,etc ># ># Here you should specify what pppd plugins you want to use ># Available plugins are: pppoe, pppoa, capi, dhcpc, minconn, radius, ># radattr, radrealms and winbind >#plugins_ppp0=( ># "pppoe" # Required plugin for PPPoE ># "pppoa" # Required plugin for PPPoA ># "capi" # Required plugin for ISDN >#) ># ># PPP requires at least a username. You can optionally set a password here too ># If you don't, then it will use the password specified in /etc/ppp/*-secrets ># against the specified username >#username_ppp0='user' >#password_ppp0='password' ># ># The PPP daemon has many options you can specify - although there are many ># and may seem daunting, it is recommended that you read the pppd man page ># before enabling any of them. ># Also, please note that this set of options isn't complete. You could use ># any pppd options presented in 'man pppd' but a very short list of forced (or forbidden) ># options: persist, maxfail, nodetach and linkname >#pppd_ppp0=( ># updetach # WARNING: If you don't specify this then we will ># # not wait for the actual PPP link to go up ># debug hide-password # Enables syslog debugging but don't show the password in logs ># noauth # Do not require the peer to authenticate itself ># defaultroute # Make this PPP interface the default route ># usepeerdns # Use the DNS settings provided by PPP ># ># On demand options ># demand # Enable dial on demand ># idle 30 # The link will go down after 30 seconds of inactivity ># holdoff 3 # Wait 3 seconds after link dies before re-starting ># 10.112.112.112:10.112.112.113 # Phony IP addresses ># ipcp-accept-remote # Accept the peers idea of remote address ># ipcp-accept-local # Accept the peers idea of local address ># ># Dead peer detection ># lcp-echo-interval 15 # Send a LCP echo every 15 seconds ># lcp-echo-failure 3 # Declare peer dead if after 3 LCP echo-requests ># # we don't receive at least one LCP echo-reply ># ># Compression options - use these to completely disable compression ># noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp ># ># Dial-up settings ># lock # Lock serial port ># 115200 # Set the serial port baud rate ># modem crtscts # Enable hardware flow control ># 192.168.0.1:192.168.0.2 # Local and remote IP addresses >#) ># ># Dial-up PPP users need to specify at least one telephone number >#phone_number_ppp0=( "12345689" ) # Maximum 2 phone numbers are supported ># They will also need a chat script - here's a good one >#chat_ppp0=( ># 'ABORT' 'BUSY' ># 'ABORT' 'ERROR' ># 'ABORT' 'NO ANSWER' ># 'ABORT' 'NO CARRIER' ># 'ABORT' 'NO DIALTONE' ># 'ABORT' 'Invalid Login' ># 'ABORT' 'Login incorrect' ># 'TIMEOUT' '5' ># '' 'ATZ' ># 'OK' 'AT' # Put your modem initialization string here ># 'OK' 'ATDT\T' ># 'TIMEOUT' '60' ># 'CONNECT' '' ># 'TIMEOUT' '5' ># '~--' '' >#) >
You cannot view the attachment while viewing its details because your browser does not support IFRAMEs.
View the attachment on a separate page
.
View Attachment As Raw
Actions:
View
Attachments on
bug 114551
:
74915
| 74916