proposed ppp section of net.example

net.example (text/plain), 3.93 KB, created by Alin Năstac (RETIRED) on 2005-12-17 01:00:04 UTC

#-----------------------------------------------------------------------------
# PPP
# For PPP support, emerge net-dialup/ppp
# PPP is used for most dialup connections, including ADSL.
# The older ADSL module is documented below, but you are encouraged to try
# this module first.
#
# You need to create the PPP net script yourself. Make it like so
#cd /etc/init.d
#ln -s net.lo net.ppp0
#
# Configure the interface to use the ppp module
#config_ppp0=( "ppp" )
#
# Each PPP interface requires an interface to use for sending/receiving PPP frames
#link_ppp0="/dev/ttyS0"              # Most PPP links will use a serial port
#link_ppp0="eth0"                    # PPPoE requires an ethernet interface
#link_ppp0="/dev/null"               # PPPoA and ISDN links should have this
#link_ppp0="pty 'your_link_command'" # PPP links over ssh,rsh,etc
#
# Here you should specify what pppd plugins you want to use
# Available plugins are: pppoe, pppoa, capi, dhcpc, minconn, radius,
#                         radattr, radrealms and winbind 
#plugins_ppp0=(
#        "pppoe" # Required plugin for PPPoE
#        "pppoa" # Required plugin for PPPoA
#        "capi"  # Required plugin for ISDN
#)
#
# PPP requires at least a username. You can optionally set a password here too
# If you don't, then it will use the password specified in /etc/ppp/*-secrets
# against the specified username
#username_ppp0='user'
#password_ppp0='password'
#
# The PPP daemon has many options you can specify - although there are many
# and may seem daunting, it is recommended that you read the pppd man page
# before enabling any of them. 
# Also, please note that this set of options isn't complete. You could use
# any pppd options presented in 'man pppd' but a very short list of forced (or forbidden)
# options: persist, maxfail, nodetach and linkname
#pppd_ppp0=(
#        updetach            # WARNING: If you don't specify this then we will
#                            # not wait for the actual PPP link to go up
#        debug hide-password # Enables syslog debugging but don't show the password in logs
#        noauth              # Do not require the peer to authenticate itself
#        defaultroute        # Make this PPP interface the default route
#        usepeerdns          # Use the DNS settings provided by PPP
#
# On demand options
#        demand               # Enable dial on demand
#        idle 30              # The link will go down after 30 seconds of inactivity
#        10.112.112.112:10.112.112.113  # Phony IP addresses
#        ipcp-accept-remote   # Accept the peers idea of remote address
#        ipcp-accept-local    # Accept the peers idea of local address
#        holdoff 3            # Wait 3 seconds after link dies before re-starting
#        lcp-echo-interval 15 # Send a LCP echo every 15 seconds
#        lcp-echo-failure 3   # Declare peer dead if no echo-replies are received
#                             # after n consecutive LCP echo-requests
#        
# Compression options - use these to completely disable compression
#        noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp
#
# Dial-up settings
#        lock                     # Lock serial port
#        115200                   # Set the serial port baud rate
#        modem crtscts            # Enable hardware flow control
#        192.168.0.1:192.168.0.2  # Local and remote IP addresses
#)
#
# Dial-up PPP users need to specify at least one telephone number
#phone_number_ppp0=( "12345689" ) # Maximum 2 phone numbers are supported
# They will also need a chat script - here's a good one
#chat_ppp0=(
#        'ABORT' 'BUSY'
#        'ABORT' 'ERROR'
#        'ABORT' 'NO ANSWER'
#        'ABORT' 'NO CARRIER'
#        'ABORT' 'NO DIALTONE'
#        'ABORT' 'Invalid Login'
#        'ABORT' 'Login incorrect'
#        'TIMEOUT' '5'
#        '' 'ATZ'
#        'OK' 'AT' # Put your modem initialization string here
#        'OK' 'ATDT\T'
#        'TIMEOUT' '60'
#        'CONNECT' ''
#        'TIMEOUT' '5'
#        '~--' ''
#)