dmesg & hdparm results for kernel 2.6.11-r11

kernel-2.6.11-r11.log (text/plain), 14.55 KB, created by Sergey Belyashov on 2005-07-16 05:54:50 UTC

Bootdata ok (command line is ro root=/dev/hdb1 quiet 3)
Linux version 2.6.11-gentoo-r11 (root@BSA-home) (gcc version 3.4.3 20041125 (Gentoo 3.4.3-r1, ssp-3.4.3-0, pie-8.7.7)) #5 Thu Jul 14 21:33:44 MSD 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
 BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
ACPI: RSDP (v000 Nvidia                                ) @ 0x00000000000f91c0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff30c0
ACPI: SSDT (v001 PTLTD  POWERNOW 0x00000001  LTP 0x00000001) @ 0x000000003fff9680
ACPI: SRAT (v001 AMD    HAMMER   0x00000001 AMD  0x00000001) @ 0x000000003fff9780
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff9880
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff95c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 262128
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 258032 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ 750c000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Built 1 zonelists
Kernel command line: ro root=/dev/hdb1 quiet 3 console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1809.312 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1025956k/1048512k available (2635k kernel code, 21856k reserved, 1190k data, 152k init)
Calibrating delay loop... 3588.09 BogoMIPS (lpj=1794048)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC NMI watchdog using perfctr0
Using local APIC timer interrupts.
Detected 12.564 MHz APIC timer.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to [e-mail]
** so I can fix the driver.
PCI-DMA: Disabling IOMMU.
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
inotify device minor=63
Initializing Cryptographic API
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
ipmi message handler version v33
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (22 C)
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe ([e-mail]) and [e-mail]
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.31.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 23 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:0a.0 to 64
eth0: forcedeth.c: subsystem: 01462:7125 bound to 0000:00:0a.0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
    ide0: BM-DMA at 0xfb00-0xfb07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xfb08-0xfb0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: HDS722580VLAT20, ATA DISK drive
hdb: Maxtor 2B020H1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
hdd: _NEC DVD_RW ND-3520AW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 160836480 sectors (82348 MB) w/1794KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 > hda3
hdb: max request size: 128KiB
hdb: 40020624 sectors (20490 MB) w/2048KiB Cache, CHS=39703/16/63, UDMA(100)
hdb: cache flushes not supported
 hdb: hdb1 hdb2
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
hdc: No disk in drive
hdc: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 22 (level, low) -> IRQ 185
ehci_hcd 0000:00:02.1: PCI device 10de:005b (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: irq 185, pci mem 0xfeb00000
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: park 0
ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
I2O subsystem v$Rev$
i2o: max drivers = 8
i2c /dev entries driver
w83627hf 0-0290: Reading VID from GPIO5
Advanced Linux Sound Architecture Driver Version 1.0.8 (Thu Jan 13 09:39:32 2005 UTC).
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 19 (level, low) -> IRQ 193
ALSA device list:
  #0: Sound Blaster Live! (rev.8, serial:0x80641102) at 0xef00, irq 193
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xa, vid 0x6
ReiserFS: hdb1: found reiserfs format "3.6" with standard journal
usb 1-8: new high speed USB device using ehci_hcd and address 2
ReiserFS: hdb1: using ordered data mode
ReiserFS: hdb1: journal params: device hdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb1: checking transaction log (hdb1)
ReiserFS: hdb1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 152k freed
Adding 2097140k swap on /dev/hda7.  Priority:-1 extents:1
ReiserFS: hdb2: found reiserfs format "3.6" with standard journal
ReiserFS: hdb2: using ordered data mode
ReiserFS: hdb2: journal params: device hdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb2: checking transaction log (hdb2)
ReiserFS: hdb2: Using r5 hash to sort names
NTFS driver 2.1.22 [Flags: R/O MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
hdc: No disk in drive
SCSI subsystem initialized
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:05:00.0 to 64
NVRM: loading NVIDIA Linux x86_64 NVIDIA Kernel Module  1.0-7664  Wed May 25 22:14:12 PDT 2005

------------------------------------------------------------------------------------
/dev/hdb:
 multcount    = 16 (on)
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  1 (on)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 39703/16/63, sectors = 20490559488, start = 0
------------------------------------------------------------------------------------
/dev/hdb:

ATA device, with non-removable media
	Model Number:       Maxtor 2B020H1                          
	Serial Number:      B1ELDQ1E            
	Firmware Revision:  WAH21PB0
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 0 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:   40020624
	device size with M = 1024*1024:       19541 MBytes
	device size with M = 1000*1000:       20490 MBytes (20 GB)
Capabilities:
	LBA, IORDY(can be disabled)
	bytes avail on r/w long: 57	Queue depth: 1
	Standby timer values: spec'd by Standard, no device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Advanced power management level: unknown setting (0x0000)
	Recommended acoustic management value: 192, current value: 254
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	NOP cmd
	   *	READ BUFFER cmd
	   *	WRITE BUFFER cmd
	   *	Host Protected Area feature set
	   *	Look-ahead
		Write cache
	   *	Power Management feature set
	   *	SMART feature set
	   *	Device Configuration Overlay feature set 
	   *	Automatic Acoustic Management feature set 
		SET MAX security extension
		Advanced Power Management feature set
	   *	DOWNLOAD MICROCODE cmd
HW reset results:
	CBLID- above Vih
	Device num = 1 determined by the jumper
Checksum: correct
------------------------------------------------------------------------------------
/dev/hdb:
 Timing cached reads:   3296 MB in  2.00 seconds = 1645.78 MB/sec
 Timing buffered disk reads:   62 MB in  3.61 seconds =  17.16 MB/sec