Error-Message from uploading to an arduino uno

arduino-error.log (text/x-log), 3.40 KB, created by Martin Zwicknagl on 2020-02-23 16:48:06 UTC

avrdude: Version 6.3-20190619
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/home/moscht/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino17/etc/avrdude.conf"
         User configuration file is "/home/moscht/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/ttyUSB0
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : Arduino
         Description     : Arduino

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x90
         Hardware Version: 3
         Firmware Version: 40887376.4

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x90

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x88

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x88

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x90
         Vtarget         : 0.0 V
         Varef           : 0.3 V
         Oscillator      : Off
         SCK period      : 0.1 us


avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x88

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x88
avrdude: AVR device initialized and ready to accept instructions

Der ausgewählte serielle Port 
 ist nicht vorhanden oder das Board ist nicht angeschlossen
Reading | 
avrdude: arduino_read_sig_bytes(): (a) protocol error, expect=0x10, resp=0xfc
avrdude: error reading signature data for part "ATmega328P", rc=-3
avrdude: error reading signature data, rc=-3

avrdude done.  Thank you.