dmesg of 2.4.7-r14 boot

dmesg.txt (text/plain), 12.16 KB, created by Lee Thompson on 2004-10-14 15:26:56 UTC

Bootdata ok (command line is root=/dev/hde2 acpi=off pci=noacpi)
Linux version 2.6.7-gentoo-r14 (root@eeyore) (gcc version 3.3.4 20040623 (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #2 SMP Wed Oct 13 14:32:25 CDT 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
 BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Scanning NUMA topology in Northbridge 24
Number of nodes 1 (0)
Node 0 MemBase 0000000000000000 Limit 000000003fff0000
Using node hash shift of 24
Bootmem setup node 0 0000000000000000-000000003fff0000
No mptable found.
On node 0 totalpages: 262128
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 258032 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
Intel MultiProcessor Specification v1.4
    Virtual Wire compatibility mode.
OEM ID: OEM00000 <6>Product ID: PROD00000000 <6>APIC at: 0xFEE00000
Processor #0 15:15 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 1
Checking aperture...
CPU 0: aperture @ f0000000 size 128 MB
Built 1 zonelists
Kernel command line: root=/dev/hde2 acpi=off pci=noacpi console=tty0
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2210.131 MHz processor.
Console: colour VGA+ 80x25
Memory: 1027928k/1048512k available (2754k kernel code, 0k reserved, 1329k data, 496k init)
Calibrating delay loop... 4374.52 BogoMIPS
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU0: AMD Athlon(tm) 64 Processor 3500+ stepping 00
per-CPU timeslice cutoff: 511.95 usecs.
task migration cache decay timeout: 1 msecs.
Only one processor found.
ENABLING IO-APIC IRQs
Using IO-APIC 2
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-9, 2-16, 2-17, 2-18, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ... 
..... (found pin 0) ...works.
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00170011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 0
.......     : IO APIC version: 0011
.... register #02: 02000000
.......     : arbitration: 02
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 001 01  0    0    0   0   0    1    1    31
 01 001 01  0    0    0   0   0    1    1    39
 02 000 00  1    0    0   0   0    0    0    00
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 000 00  1    0    0   0   0    0    0    00
 0a 001 01  0    0    0   0   0    1    1    71
 0b 001 01  0    0    0   0   0    1    1    79
 0c 001 01  0    0    0   0   0    1    1    81
 0d 001 01  0    0    0   0   0    1    1    89
 0e 001 01  0    0    0   0   0    1    1    91
 0f 001 01  0    0    0   0   0    1    1    99
 10 000 00  1    0    0   0   0    0    0    00
 11 000 00  1    0    0   0   0    0    0    00
 12 000 00  1    0    0   0   0    0    0    00
 13 001 01  1    1    0   1   0    1    1    A1
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
Detected 12.557 MHz APIC timer.
time.c: Using PIT/TSC based timekeeping.
Brought up 1 CPUs
CPU0:  online
 domain 0: span 01
  groups: 01
  domain 1: span 01
   groups: 01
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [10de/00e1] at 0000:00:00.0
PCI->APIC IRQ transform: (B2,I12,P0) -> 19
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xf0000000
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
devfs: 2004-01-31 Richard Gooch ([e-mail])
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 [e-mail]).
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
sk98lin: No adapter found.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
r8169 Gigabit Ethernet driver 1.2 loaded
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xffffff0000046000, 00:11:09:66:07:cc, IRQ 5
eth0: Auto-negotiation Enabled.
eth0: 100Mbps Full-duplex operation.
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: PLEXTOR DVDR PX-712A, ATAPI CD/DVD-ROM drive
hdb: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
NFORCE3-250-SATA2: IDE controller at PCI slot 0000:00:09.0
NFORCE3-250-SATA2: chipset revision 162
NFORCE3-250-SATA2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250-SATA2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250-SATA2: 0000:00:09.0 (rev a2) UDMA133 controller
NFORCE3-250-SATA2: 100% native mode on irq 11
    ide2: BM-DMA at 0xc800-0xc807, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xc808-0xc80f, BIOS settings: hdg:pio, hdh:pio
hde: WDC WD740GD-00FLA0, ATA DISK drive
ide2 at 0x9e0-0x9e7,0xbe2 on irq 11
hdg: WDC WD740GD-00FLA0, ATA DISK drive
ide3 at 0x960-0x967,0xb62 on irq 11
NFORCE3-250-SATA: IDE controller at PCI slot 0000:00:0a.0
NFORCE3-250-SATA: chipset revision 162
NFORCE3-250-SATA: 0000:00:0a.0 (rev a2) UDMA133 controller
NFORCE3-250-SATA: 100% native mode on irq 10
    ide4: BM-DMA at 0xe000-0xe007, BIOS settings: hdi:pio, hdj:pio
    ide5: BM-DMA at 0xe008-0xe00f, BIOS settings: hdk:pio, hdl:pio
hde: max request size: 1024KiB
hde: 145226112 sectors (74355 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(133)
 /dev/ide/host2/bus0/target0/lun0: p1 p2 p3 p4
hdg: max request size: 1024KiB
hdg: 145226112 sectors (74355 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(133)
 /dev/ide/host2/bus1/target0/lun0: p1 p2
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW CD-MRW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 52X CD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
3ware Storage Controller device driver for Linux v1.26.00.039.
3w-xxxx: No cards found.
libata version 1.02 loaded.
Fusion MPT base driver 3.01.06
Copyright (c) 1999-2004 LSI Logic Corporation
Fusion MPT SCSI Host driver 3.01.06
ehci_hcd 0000:00:02.2: PCI device 10de:00e8 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 5, pci mem ffffff000004c000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ohci_hcd 0000:00:02.0: PCI device 10de:00e7 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 5, pci mem ffffff000004e000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd 0000:00:02.1: PCI device 10de:00e7 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 5, pci mem ffffff0000050000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Intel 810 + AC97 Audio, version 1.01, 14:30:59 Oct 13 2004
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 64Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 496k freed
ohci_hcd 0000:00:02.0: remote wakeup
Adding 2008084k swap on /dev/hdg1.  Priority:-1 extents:1
EXT3 FS on hde2, internal journal
usb 2-2: new low speed USB device using address 2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-2
hde: dma_timer_expiry: dma status == 0x24
hdg: dma_timer_expiry: dma status == 0x24
hde: DMA interrupt recovery
hde: lost interrupt
hdg: DMA interrupt recovery
hdg: lost interrupt
hde: dma_timer_expiry: dma status == 0x24
hdg: dma_timer_expiry: dma status == 0x24
hde: DMA interrupt recovery
hde: lost interrupt
hdg: DMA interrupt recovery
hdg: lost interrupt
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hde3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hde4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdg2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: no IPv6 routers present
hde: dma_timer_expiry: dma status == 0x24
hdg: dma_timer_expiry: dma status == 0x24
hde: DMA interrupt recovery
hde: lost interrupt
hdg: DMA interrupt recovery
hdg: lost interrupt