New version of config script

net (text/plain), 4.19 KB, created by Roy Marples (RETIRED) on 2004-04-02 01:51:50 UTC

# /etc/conf.d/net:

# Global config file for net.* rc-scripts

# This is basically the ifconfig argument without the ifconfig $iface
#
#iface_eth0="192.168.0.13 broadcast 192.168.0.255 netmask 255.255.255.0"
#iface_eth1="207.170.82.202 broadcast 207.0.255.255 netmask 255.255.0.0"

# For DHCP set iface_eth? to "dhcp"
# For passing options to dhcpcd use dhcpcd_eth?
#
iface_eth0="dhcp"
#dhcpcd_eth0="..."
#iface_eth1="dhcp"
#dhcpcd_eth1="..."

# An external script can be run by specifying its location below
#preifup_eth0="/run/this/script"
#preifdown_eth=0"/run/this/script"
#postifup_eth0="/run/this/script"
#postifdown_eth=0"/run/this/script"

##############################################################################
#                             Wireless settings                              #
##############################################################################

# Hard code an ESSID to an interface
# This needs to be done when the driver doesn't support scanning
# Set to "any" to connect to any ESSID
# This may work for drivers that don't support scanning but you need automatic AP association
#wireless_essid_eth0="any"

# Set the mode of the interface. Managed is default
#wireless_mode_eth0="Managed"

# Setup any other config commands. This is basically the iwconfig argument
# without the iwconfig $iface
#wireless_config_eth0=""

# Set private driver ioctls. This is basically the iwpriv argument without
# the iwpriv $iface
#wireless_priv_eth0=""

# Some drivers need to scan in Ad-Hoc mode
# After scan, the mode is reset to the one defined above
#wireless_scan_mode_eth0="Ad-Hoc"

# We can define various timeouts in seconds here
#wireless_sleep_scan_eth0="1"
#wireless_sleep_associate_eth0="5"

# Below you can define private ioctls to run before and after scanning
# Format is the same as the wireless_priv above
# This is needed for the HostAP drivers
#wireless_priv_scan_pre_eth0="host_roaming 2"
#wireless_priv_scan_post_eth0="host_roaming 0"

# Define a WEP key per ESSID
# IMPORTANT: any characters that are NOT in a_z A_Z 0_9 should be
# replaced with the _ character. For example #123 becomes _123
# wireless_key takes the same parameters as the key function in iwconfig
# You can also set iface, dhcpcd and gateway options per ESSID
# If they aren't set then the defaults for the interface are used
# IMPORTANT: don't set an interface for wireless gateway - just use an IP address
# The below examples use ESSID - change it to yours.
# You can't use "any" for an ESSID here
#wireless_key_ESSID="open 1234-1234-1234-1234-1234-1234-56"
# or you can use strings. Passphrase IS NOT supported
#wireless_key_ESSID="open s:foobar"

# You can also override the interace settings here - even provide
# a nameserver/domain per ESSID
#wireless_iface_ESSID="dhcp"
#wireless_dhcpcd_ESSID="..."
#wireless_gateway_ESSID="192.168.0.1"
#wireless_nameserver_ESSID=""
#wireless_domain_ESSID=""

# LEAP users will want to use the preassociate setting to specify
# an authentication script
#wireless_preassociate_ESSID="/run/this/script"
#wireless_preifup_ESSID="/run/this/script"
#wireless_preifdown_ESSID="/run/this/script"
#wireless_postifup_ESSID="/run/this/script"
#wireless_postifdown_ESSID="/run/this/script"

# This lists the preferred ESSIDs to connect to in order
# ESSID's can contain any characters here as they must match the broadcast
# ESSID exactly
# Seperate the ESSIDs with tabs - NOT spaces
# If the first ESSID isn't found then it moves onto the next
# If this isn't defined then it connects to the first one found
#wireless_preferred="ESSID1	ESSID2	ESSID3	ESSID4"

##############################################################################
#                            End Wireless Settings                           #
##############################################################################

# For adding aliases to a interface
#
#alias_eth0="192.168.0.3 192.168.0.4"

# NB:  The next is only used for aliases.
#
# To add a custom netmask/broadcast address to created aliases,
# uncomment and change accordingly.  Leave commented to assign
# defaults for that interface.
#
#broadcast_eth0="192.168.0.255 192.168.0.255"
#netmask_eth0="255.255.255.0 255.255.255.0"


# For setting the default gateway
#
#gateway="eth0/192.168.0.1"