kernel log

dmesg.log (text/plain), 36.47 KB, created by Piergiorgio Beruto on 2011-08-20 20:01:50 UTC

Linux version 3.0.3-gentoo-cirith-ungol (root@shelob) (gcc version 4.5.3 (Gentoo 4.5.3-r1 p1.0, pie-0.4.5) ) #8 PREEMPT Sat Aug 20 15:38:30 CEST 2011
KERNEL supported cpus:
  Intel GenuineIntel
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003eee0000 (usable)
 BIOS-e820: 000000003eee0000 - 000000003eee3000 (ACPI NVS)
 BIOS-e820: 000000003eee3000 - 000000003eef0000 (ACPI data)
 BIOS-e820: 000000003eef0000 - 000000003ef00000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
DMI 2.3 present.
DMI:    /CN700-8237, BIOS 6.00 PG 11/30/2007
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
last_pfn = 0x3eee0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-CFFFF write-protect
  D0000-EFFFF uncachable
  F0000-F7FFF write-through
  F8000-F8FFF uncachable
  F9000-FFFFF write-through
MTRR variable ranges enabled:
  0 base 000000000 mask FC0000000 write-back
  1 base 03F000000 mask FFF000000 uncachable
  2 base 0E8000000 mask FF8000000 write-combining
  3 base 03EF00000 mask FFFF00000 uncachable
  4 disabled
  5 disabled
  6 disabled
  7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 00800000
Base memory trampoline at [b009e000] 9e000 size 4096
init_memory_mapping: 0000000000000000-000000003eee0000
 0000000000 - 0000400000 page 4k
 0000400000 - 003ec00000 page 2M
 003ec00000 - 003eee0000 page 4k
kernel direct mapping tables up to 3eee0000 @ 7fb000-800000
RAMDISK: 00ca7000 - 00f00000
ACPI: RSDP 000f7bc0 00014 (v00 CN700 )
ACPI: RSDT 3eee3000 0002C (v01 CN700  AWRDACPI 42302E31 AWRD 00000000)
ACPI: FACP 3eee3080 00074 (v01 CN700  AWRDACPI 42302E31 AWRD 00000000)
ACPI: DSDT 3eee3100 05281 (v01 CN700  AWRDACPI 00001000 MSFT 03000000)
ACPI: FACS 3eee0000 00040
ACPI: APIC 3eee83c0 0005A (v01 CN700  AWRDACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1006MB LOWMEM available.
  mapped low ram: 0 - 3eee0000
  low ram: 0 - 3eee0000
Zone PFN ranges:
  DMA      0x00000010 -> 0x00001000
  Normal   0x00001000 -> 0x0003eee0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009f
    0: 0x00000100 -> 0x0003eee0
On node 0 totalpages: 257647
free_area_init_node: node 0, pgdat b048528c, node_mem_map ee700200
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3951 pages, LIFO batch:0
  Normal zone: 1982 pages used for memmap
  Normal zone: 251682 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
nr_irqs_gsi: 40
Allocating PCI resources starting at 3ef00000 (gap: 3ef00000:bfd00000)
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 255633
Kernel command line: BOOT_IMAGE=Gentoo_3.0.3 ro root=802 console=tty0 console=ttyS0,115200n8 libata.force=3:pio4 domdadm dolvm real_root=/dev/sdc2
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Initializing CPU#0
Memory: 1015204k/1031040k available (2693k kernel code, 15384k reserved, 931k data, 248k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffa3000 - 0xfffff000   ( 368 kB)
    vmalloc : 0xef6e0000 - 0xfffa1000   ( 264 MB)
    lowmem  : 0xb0000000 - 0xeeee0000   (1006 MB)
      .init : 0xb048b000 - 0xb04c9000   ( 248 kB)
      .data : 0xb03a14e8 - 0xb048a440   ( 931 kB)
      .text : 0xb0100000 - 0xb03a14e8   (2693 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:288
CPU 0 irqstacks, hard=ee00e000 soft=ee010000
Console: colour VGA+ 80x25
console [tty0] enabled
console [ttyS0] enabled
Fast TSC calibration using PIT
Detected 1200.033 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 2400.06 BogoMIPS (lpj=4800132)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Centaur VIA Eden Processor 1200MHz stepping 00
ACPI: Core revision 20110413
Performance Events: 
Enabling APIC mode:  Flat.  Using 1 I/O APICs
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfa180, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Actual Package length (8) is larger than NumElements field (2), truncated

ACPI: Actual Package length (8) is larger than NumElements field (2), truncated

ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x3ef00000-0xfebfffff] (ignored)
pci 0000:00:00.0: [1106:0314] type 0 class 0x000600
pci 0000:00:00.0: reg 10: [mem 0xe8000000-0xefffffff pref]
pci 0000:00:00.1: [1106:1314] type 0 class 0x000600
pci 0000:00:00.2: [1106:2314] type 0 class 0x000600
pci 0000:00:00.3: [1106:3208] type 0 class 0x000600
pci 0000:00:00.4: [1106:4314] type 0 class 0x000600
pci 0000:00:00.7: [1106:7314] type 0 class 0x000600
pci 0000:00:01.0: [1106:b198] type 1 class 0x000604
pci 0000:00:01.0: supports D1
pci 0000:00:08.0: [168c:0023] type 0 class 0x000280
pci 0000:00:08.0: reg 10: [mem 0xfdfe0000-0xfdfeffff]
pci 0000:00:09.0: [10ec:8167] type 0 class 0x000200
pci 0000:00:09.0: reg 10: [io  0xf200-0xf2ff]
pci 0000:00:09.0: reg 14: [mem 0xfdfff000-0xfdfff0ff]
pci 0000:00:09.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:00:09.0: supports D1 D2
pci 0000:00:09.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:00:09.0: PME# disabled
pci 0000:00:0f.0: [1106:3149] type 0 class 0x000101
pci 0000:00:0f.0: reg 10: [io  0xff00-0xff07]
pci 0000:00:0f.0: reg 14: [io  0xfe00-0xfe03]
pci 0000:00:0f.0: reg 18: [io  0xfd00-0xfd07]
pci 0000:00:0f.0: reg 1c: [io  0xfc00-0xfc03]
pci 0000:00:0f.0: reg 20: [io  0xfb00-0xfb0f]
pci 0000:00:0f.0: reg 24: [io  0xf400-0xf4ff]
pci 0000:00:0f.1: [1106:0571] type 0 class 0x000101
pci 0000:00:0f.1: reg 20: [io  0xfa00-0xfa0f]
pci 0000:00:10.0: [1106:3038] type 0 class 0x000c03
pci 0000:00:10.0: reg 20: [io  0xf900-0xf91f]
pci 0000:00:10.0: supports D1 D2
pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.0: PME# disabled
pci 0000:00:10.1: [1106:3038] type 0 class 0x000c03
pci 0000:00:10.1: reg 20: [io  0xf800-0xf81f]
pci 0000:00:10.1: supports D1 D2
pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:00:10.2: [1106:3038] type 0 class 0x000c03
pci 0000:00:10.2: reg 20: [io  0xf700-0xf71f]
pci 0000:00:10.2: supports D1 D2
pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.2: PME# disabled
pci 0000:00:10.3: [1106:3038] type 0 class 0x000c03
pci 0000:00:10.3: reg 20: [io  0xf600-0xf61f]
pci 0000:00:10.3: supports D1 D2
pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.3: PME# disabled
pci 0000:00:10.4: [1106:3104] type 0 class 0x000c03
pci 0000:00:10.4: reg 10: [mem 0xfdffe000-0xfdffe0ff]
pci 0000:00:10.4: supports D1 D2
pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.4: PME# disabled
pci 0000:00:11.0: [1106:3227] type 0 class 0x000601
pci 0000:01:00.0: [1106:3344] type 0 class 0x000300
pci 0000:01:00.0: reg 10: [mem 0xf4000000-0xf7ffffff pref]
pci 0000:01:00.0: reg 14: [mem 0xfb000000-0xfbffffff]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
pci 0000:00:01.0:   bridge window [mem 0xfb000000-0xfcffffff]
pci 0000:00:01.0:   bridge window [mem 0xf4000000-0xf7ffffff pref]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
 pci0000:00: Unable to request _OSC control (_OSC support mask: 0x18)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22), disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled.
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
reserve RAM buffer: 000000000009f800 - 000000000009ffff 
reserve RAM buffer: 000000003eee0000 - 000000003fffffff 
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: [mem 0x000f0000-0x000fffff]
pnp 00:00: [mem 0x3eee0000-0x3eefffff]
pnp 00:00: [mem 0xffff0000-0xffffffff]
pnp 00:00: [mem 0x00000000-0x0009ffff]
pnp 00:00: [mem 0x00100000-0x3eedffff]
pnp 00:00: [mem 0xfec00000-0xfecfffff]
pnp 00:00: [mem 0xfee00000-0xfeefffff]
pnp 00:00: [mem 0xfff80000-0xfffeffff]
system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
system 00:00: [mem 0x3eee0000-0x3eefffff] could not be reserved
system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:00: [mem 0x00100000-0x3eedffff] could not be reserved
system 00:00: [mem 0xfec00000-0xfecfffff] could not be reserved
system 00:00: [mem 0xfee00000-0xfeefffff] could not be reserved
system 00:00: [mem 0xfff80000-0xfffeffff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:01: [bus 00-ff]
pnp 00:01: [io  0x0cf8-0x0cff]
pnp 00:01: [io  0x0000-0x0cf7 window]
pnp 00:01: [io  0x0d00-0xffff window]
pnp 00:01: [mem 0x000a0000-0x000bffff window]
pnp 00:01: [mem 0x000c0000-0x000dffff window]
pnp 00:01: [mem 0x3ef00000-0xfebfffff window]
pnp 00:01: [mem 0x00000000 window]
pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:02: [io  0x0400-0x047f]
pnp 00:02: [io  0x0500-0x050f]
system 00:02: [io  0x0400-0x047f] has been reserved
system 00:02: [io  0x0500-0x050f] has been reserved
system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:03: [io  0x0010-0x001f]
pnp 00:03: [io  0x0022-0x003f]
pnp 00:03: [io  0x0044-0x005f]
pnp 00:03: [io  0x0062-0x0063]
pnp 00:03: [io  0x0065-0x006f]
pnp 00:03: [io  0x0074-0x007f]
pnp 00:03: [io  0x0091-0x0093]
pnp 00:03: [io  0x00a2-0x00bf]
pnp 00:03: [io  0x00e0-0x00ef]
pnp 00:03: [io  0x04d0-0x04d1]
pnp 00:03: [io  0x0800-0x0805]
pnp 00:03: [io  0x0290-0x0297]
system 00:03: [io  0x04d0-0x04d1] has been reserved
system 00:03: [io  0x0800-0x0805] has been reserved
system 00:03: [io  0x0290-0x0297] has been reserved
system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:04: [dma 4]
pnp 00:04: [io  0x0000-0x000f]
pnp 00:04: [io  0x0080-0x0090]
pnp 00:04: [io  0x0094-0x009f]
pnp 00:04: [io  0x00c0-0x00df]
pnp 00:04: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:05: [io  0x0070-0x0073]
pnp 00:05: [irq 8]
pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:06: [io  0x0061]
pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:07: [io  0x00f0-0x00ff]
pnp 00:07: [irq 13]
pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:08: [io  0x03f8-0x03ff]
pnp 00:08: [irq 4]
pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
Switching to clocksource acpi_pm
PCI: max bus depth: 1 pci_try_num: 2
pci 0000:00:09.0: BAR 6: assigned [mem 0x40000000-0x4001ffff pref]
Switched to NOHz mode on CPU #0
pci 0000:01:00.0: BAR 6: assigned [mem 0xfc000000-0xfc00ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
pci 0000:00:01.0:   bridge window [mem 0xfb000000-0xfcffffff]
pci 0000:00:01.0:   bridge window [mem 0xf4000000-0xf7ffffff pref]
pci 0000:00:01.0: setting latency timer to 64
pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
pci_bus 0000:01: resource 1 [mem 0xfb000000-0xfcffffff]
pci_bus 0000:01: resource 2 [mem 0xf4000000-0xf7ffffff pref]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:01.0: disabling DAC on VIA PCI bridge
pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
pci 0000:01:00.0: Boot video device
PCI: CLS 64 bytes, default 64
Unpacking initramfs...
Freeing initrd memory: 2404k freed
Installing knfsd (copyright (C) 1996 [e-mail]).
msgmni has been set to 1987
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.12b
VIA RNG detected
Linux agpgart interface v0.103
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
ACPI: Fan [FAN] (on)
ACPI: acpi_idle registered with cpuidle
Marking TSC unstable due to TSC halts in idle
thermal LNXTHERM:00: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (39 C)
[drm] Initialized drm 1.1.0 20060810
pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized via 2.11.1 20070202 for 0000:01:00.0 on minor 0
sata_via 0000:00:0f.0: version 2.6
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
sata_via 0000:00:0f.0: PCI INT B -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
sata_via 0000:00:0f.0: routed to hard irq line 11
scsi0 : sata_via
scsi1 : sata_via
ata1: SATA max UDMA/133 cmd 0xff00 ctl 0xfe00 bmdma 0xfb00 irq 20
ata2: SATA max UDMA/133 cmd 0xfd00 ctl 0xfc00 bmdma 0xfb08 irq 20
pata_via 0000:00:0f.1: version 0.3.4
pata_via 0000:00:0f.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
scsi2 : pata_via
scsi3 : pata_via
ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[e-mail]>
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:00:09.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
r8169 0000:00:09.0: (unregistered net_device): no PCI Express capability
r8169 0000:00:09.0: eth0: RTL8169sc/8110sc at 0xef6f4000, 00:30:18:ad:ee:00, XID 18000000 IRQ 18
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ehci_hcd 0000:00:10.4: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdffe000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 21, io base 0x0000f900
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 21, io base 0x0000f800
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io base 0x0000f700
hub 4-0:1.0: USB hub found
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-0: SMI MODEL, 20071116, max MWDMA2
hub 4-0:1.0: 2 ports detected
ata3.00: 7928928 sectors, multi 0: LBA 
uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
ata3.00: FORCE: xfer_mask set to pio4
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 21, io base 0x0000f600
hub 5-0:1.0: USB hub found
ata3.00: configured for PIO4
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
f71805f: Found F71805F/FG chip at 0x290, revision 19
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [e-mail]
eps: Detected VIA Model D Eden
eps: Current voltage = 860mV
eps: Current multiplier = 12
eps: Highest voltage = 860mV
eps: Highest multiplier = 12
eps: Lowest voltage = 844mV
eps: Lowest multiplier = 4
cpuidle: using governor ladder
cpuidle: using governor menu
padlock_aes: Using VIA PadLock ACE for AES algorithm.
padlock_sha: Using VIA PadLock ACE for SHA1/SHA256 algorithms.
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nf_conntrack version 0.5.0 (15900 buckets, 63600 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
Using IPI Shortcut mode
ata1.00: ATA-8: WDC WD5000BUDT-63G8FY0, 01.01A01, max UDMA/133
ata1.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000BUDT-6 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-8: WDC WD5000BUDT-63G8FY0, 01.01A01, max UDMA/133
ata2.00: 976773168 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      WDC WD5000BUDT-6 01.0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
scsi 2:0:0:0: Direct-Access     ATA      SMI MODEL        2007 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 4096-byte physical blocks
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 7928928 512-byte logical blocks: (4.05 GB/3.78 GiB)
ata4: port disabled. ignoring.
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc1 sdc2
sd 2:0:0:0: [sdc] Attached SCSI disk
 sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Attached SCSI disk
Freeing unused kernel memory: 248k freed
md: md127 stopped.
md: bind<sdb3>
md: bind<sda3>
bio: create slab <bio-1> at 1
md/raid0:md127: looking at sda3
md/raid0:md127:   comparing sda3(706236416) with sda3(706236416)
md/raid0:md127:   END
md/raid0:md127:   ==> UNIQUE
md/raid0:md127: 1 zones
md/raid0:md127: looking at sdb3
md/raid0:md127:   comparing sdb3(706236416) with sda3(706236416)
md/raid0:md127:   EQUAL
md/raid0:md127: FINAL 1 zones
md/raid0:md127: done.
md/raid0:md127: md_size is 1412472832 sectors.
******* md127 configuration *********
zone0=[sda3/sdb3/]
        zone offset=0kb device offset=0kb size=706236416kb
**********************************

md127: detected capacity change from 0 to 723186089984
 md127: unknown partition table
md: md126 stopped.
md: bind<sdb2>
md: bind<sda2>
md/raid1:md126: active with 2 out of 2 mirrors
md126: detected capacity change from 0 to 137437831168
 md126: unknown partition table
EXT4-fs (sdc2): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (sdc2): couldn't mount as ext2 due to feature incompatibilities
EXT4-fs (sdc2): mounted filesystem with ordered data mode. Opts: (null)
udevd[1628]: starting version 171

<<<<<<<<<< FIRST CALL TO CRDA (doesn't complete?)

cfg80211: Calling CRDA to update world regulatory domain
ath9k 0000:00:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52

<<<<<<<<<< This seems to be world regulatory rule applying....

cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2474000 KHz - 2494000 KHz @  KHz), (600 mBi, 2000 mBm)
ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'

<<<<<<<<<<<<< this should be the second call to CRDA for country CN which is stored in the EEPROM
<<<<<<<<<<<<< but there's no "World regulatory domain updated" print, instead the request seems to be pending.

cfg80211: Pending regulatory request, waiting for it to be processed...

Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xefce0000, irq=17
EXT4-fs (sdc2): re-mounted. Opts: (null)
EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (dm-1): mounting ext2 file system using the ext4 subsystem
EXT4-fs (dm-1): mounted filesystem without journal. Opts: (null)
EXT4-fs (dm-2): mounting ext2 file system using the ext4 subsystem
EXT4-fs (dm-2): mounted filesystem without journal. Opts: (null)
REISERFS (device dm-5): found reiserfs format "3.6" with standard journal
REISERFS (device dm-5): using ordered data mode
REISERFS (device dm-5): journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
REISERFS (device dm-5): checking transaction log (dm-5)
REISERFS (device dm-5): Using r5 hash to sort names
EXT4-fs (dm-9): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (dm-8): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (dm-7): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
r8169 0000:00:09.0: eth0: link down
r8169 0000:00:09.0: eth0: link up
Adding 1048572k swap on /dev/sda1.  Priority:1 extents:1 across:1048572k 
Adding 1048572k swap on /dev/sdb1.  Priority:1 extents:1 across:1048572k 
device tap0 entered promiscuous mode
device wlan0 entered promiscuous mode
br0: port 2(wlan0) entering forwarding state
br0: port 2(wlan0) entering forwarding state
cfg80211: Pending regulatory request, waiting for it to be processed...
device wlan0 left promiscuous mode
br0: port 2(wlan0) entering forwarding state
br0: port 1(tap0) entering forwarding state
br0: port 1(tap0) entering forwarding state
xfce4-settings-[3250]: segfault at 1 ip 08050a80 sp afeb5a80 error 4 in xfce4-settings-helper[8048000+d000]
br0: port 1(tap0) entering forwarding state
ath9k 0000:00:08.0: PCI INT A disabled

<<<<<<<<<< here I've logged in the system after some minutes... then I've removed ath9k with 
<<<<<<<<<< "modprobe -rv ath9k"
ath9k: Driver unloaded

<<<<<<<<<< here I've insmodded ath9k again, and everything seems just fine
cfg80211: Calling CRDA to update world regulatory domain
ath9k 0000:00:08.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (300 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2474000 KHz - 2494000 KHz @  KHz), (300 mBi, 2000 mBm)
ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
cfg80211: Calling CRDA for country: CN
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xf0180000, irq=17
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2484 MHz
cfg80211: Regulatory domain changed to country: CN
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)

<<<<<<<<<< here I've restarted hostapd by hand which changes again the CRDA to IT
device wlan0 entered promiscuous mode
br0: port 2(wlan0) entering forwarding state
br0: port 2(wlan0) entering forwarding state
cfg80211: Calling CRDA for country: IT
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2482000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2484 MHz
cfg80211: Regulatory domain changed to country: IT
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
cfg80211:     (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
br0: port 2(wlan0) entering forwarding state