dmesg - includes CONFIG_HID_DEBUG set in config

dmesg_2.6.23-rc5_usbkeyb.txt (text/plain), 30.09 KB, created by Michael Kers on 2007-09-03 00:46:49 UTC

0 MSFT  100000E)
ACPI: FACS 1DEF0000, 0040
ACPI: SSDT 1DEFB280, 00F4 (r1 PTLTD  POWERNOW        1  LTP        1)
ACPI: MCFG 1DEFB3C0, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
ACPI: APIC 1DEFB1C0, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
Scanning NUMA topology in Northbridge 24
CPU has 1 num_cores
No NUMA configuration found
Faking a node at 0000000000000000-000000001def0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 122608) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000001def0000
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   122608
On node 0 totalpages: 122511
  DMA zone: 56 pages used for memmap
  DMA zone: 1257 pages reserved
  DMA zone: 2686 pages, LIFO batch:0
  DMA32 zone: 1620 pages used for memmap
  DMA32 zone: 116892 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:d0000000)
SMP: Allowing 2 CPUs, 1 hotplug CPUs
PERCPU: Allocating 35176 bytes of per cpu data
Built 1 zonelists in Node order.  Total pages: 119578
Policy zone: DMA32
Kernel command line: root=/dev/ram0 init=/linuxrc real_root=/dev/md1 md=1,/dev/sda2, /dev/sdb2 
md: Will configure md1 (super-block) from /dev/sda2,, below.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 16384 bytes)
time.c: Detected 2004.217 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
CPU 0: aperture @ c496000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 475812k/490432k available (2911k kernel code, 14232k reserved, 1160k data, 328k init)
Calibrating delay using timer specific routine.. 4011.97 BogoMIPS (lpj=8023948)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
..MP-BIOS bug: 8254 timer not connected to IO-APIC
Using local APIC timer interrupts.
result 12526355
Detected 12.526 MHz APIC timer.
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at f0000000 - f3ffffff
PCI: No mmconfig possible on device 00:18
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Time: tsc clocksource has been installed.
pnp: 00:01: ioport range 0x4000-0x407f has been reserved
pnp: 00:01: ioport range 0x4080-0x40ff has been reserved
pnp: 00:01: ioport range 0x4400-0x447f has been reserved
pnp: 00:01: ioport range 0x4480-0x44ff has been reserved
pnp: 00:01: ioport range 0x4800-0x487f has been reserved
pnp: 00:01: ioport range 0x4880-0x48ff has been reserved
pnp: 00:01: ioport range 0x2000-0x207f has been reserved
pnp: 00:01: ioport range 0x2080-0x20ff has been reserved
pnp: 00:01: iomem range 0x1e000000-0x1fffffff could not be reserved
pnp: 00:0f: iomem range 0xf0000000-0xf3ffffff could not be reserved
pnp: 00:10: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:10: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:10: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:10: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:02.0
  IO window: a000-afff
  MEM window: fd800000-fd8fffff
  PREFETCH window: fd700000-fd7fffff
PCI: Bridge: 0000:00:03.0
  IO window: 8000-8fff
  MEM window: fde00000-fdefffff
  PREFETCH window: fdd00000-fddfffff
PCI: Bridge: 0000:00:04.0
  IO window: b000-bfff
  MEM window: fdc00000-fdcfffff
  PREFETCH window: fd900000-fd9fffff
PCI: Bridge: 0000:00:10.0
  IO window: 9000-9fff
  MEM window: fdb00000-fdbfffff
  PREFETCH window: fda00000-fdafffff
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 6, 393216 bytes)
TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2362k freed
audit: initializing netlink socket (disabled)
audit(1188751149.712:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:00:05.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie03]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie03]
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
NFORCE-MCP51: chipset revision 161
NFORCE-MCP51: not 100% native mode: will probe irqs later
NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
    ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf408-0xf40f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
hda: selected mode 0x42
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 328k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0 
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 23, io mem 0xfe02e000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.23-rc5 ehci_hcd
usb usb1: SerialNumber: 0000:00:0b.1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
logips2pp: Detected unknown logitech mouse model 11
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
Initializing USB Mass Storage driver...
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 1-2: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: USB Mass Storage Device
usb 1-2: Manufacturer: Myson Century, Inc.
usb 1-2: SerialNumber: 100
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
usb-storage 1-2:1.0: usb_probe_interface
usb-storage 1-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 80 td 96
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: irq 22, io mem 0xfe02f000
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000004a MIE RHSC RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.23-rc5 ohci_hcd
usb usb2: SerialNumber: 0000:00:0b.0
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
input: PS/2 Logitech Mouse as /class/input/input1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:04:05.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[fdbff000-fdbff7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi1 : sata_nv
scsi2 : sata_nv
ata1: SATA max UDMA/133 cmd 0x00000000000109f0 ctl 0x0000000000010bf2 bmdma 0x000000000001e000 irq 21
ata2: SATA max UDMA/133 cmd 0x0000000000010970 ctl 0x0000000000010b72 bmdma 0x000000000001e008 irq 21
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3300622AS, 3.AAH, max UDMA/133
ata1.00: 586072368 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ohci_hcd 0000:00:0b.0: auto-stop root hub
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: WDC WD2500JS-00MVB1, 10.02E01, max UDMA/133
ata2.00: 488397168 sectors, multi 1: LBA48 
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      ST3300622AS      3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 < sda5 sda6 >
sd 1:0:0:0: [sda] Attached SCSI disk
scsi 2:0:0:0: Direct-Access     ATA      WDC WD2500JS-00M 10.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 sdb7 >
sd 2:0:0:0: [sdb] Attached SCSI disk
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:0f.0 to 64
scsi3 : sata_nv
scsi4 : sata_nv
ata3: SATA max UDMA/133 cmd 0x00000000000109e0 ctl 0x0000000000010be2 bmdma 0x000000000001cc00 irq 20
ata4: SATA max UDMA/133 cmd 0x0000000000010960 ctl 0x0000000000010b62 bmdma 0x000000000001cc08 irq 20
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d80000c5ab2a]
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [e-mail]
JFS: nTxBlock = 3738, nTxLock = 29906
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
scsi 0:0:0:0: Direct-Access     ST96812A                  3.06 PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sdc] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sdc] Write Protect is off
sd 0:0:0:0: [sdc] Mode Sense: 00 14 00 00
sd 0:0:0:0: [sdc] Assuming drive cache: write through
sd 0:0:0:0: [sdc] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sdc] Write Protect is off
sd 0:0:0:0: [sdc] Mode Sense: 00 14 00 00
sd 0:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1 sdc2
sd 0:0:0:0: [sdc] Attached SCSI disk
usb-storage: device scan complete
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb5 ...
md:  adding sdb5 ...
md: sdb2 has different UUID to sdb5
md: sdb1 has different UUID to sdb5
md:  adding sda5 ...
md: sda2 has different UUID to sdb5
md: sda1 has different UUID to sdb5
md: created md2
md: bind<sda5>
md: bind<sdb5>
md: running: <sdb5><sda5>
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sdb2 ...
md:  adding sdb2 ...
md: sdb1 has different UUID to sdb2
md:  adding sda2 ...
md: sda1 has different UUID to sdb2
md: created md1
md: bind<sda2>
md: bind<sdb2>
md: running: <sdb2><sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sdb1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: md1: found reiserfs format "3.6" with standard journal
ReiserFS: md1: using ordered data mode
ReiserFS: md1: journal params: device md1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md1: checking transaction log (md1)
ReiserFS: md1: Using r5 hash to sort names
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126]
ACPI: Thermal Zone [THRM] (40 C)
input: PC Speaker as /class/input/input4
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: Fan [FAN] (on)
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:10.1 to 64
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:14.0 to 64
forcedeth: using HIGHDMA
eth0: forcedeth.c: subsystem: 01043:816a bound to 0000:00:14.0
net eth2: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0 to eth2
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 0:0:0:0: Attached scsi generic sg2 type 0
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3200+ processors (1 cpu cores) (version 2.00.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x8
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0xa
powernow-k8:    2 : fid 0x2 (1000 MHz), vid 0x12
it87: Found IT8716F chip at 0x290, revision 0
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
md: md3 stopped.
md: md4 stopped.
ReiserFS: md2: found reiserfs format "3.6" with standard journal
ReiserFS: md2: using ordered data mode
ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md2: checking transaction log (md2)
ReiserFS: md2: Using r5 hash to sort names
ReiserFS: sdb7: found reiserfs format "3.6" with standard journal
ReiserFS: sdb7: using ordered data mode
ReiserFS: sdb7: journal params: device sdb7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb7: checking transaction log (sdb7)
ReiserFS: sdb7: Using r5 hash to sort names
Adding 987956k swap on /dev/sdb6.  Priority:-1 extents:1 across:987956k
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Marking TSC unstable due to cpufreq changes
Time: acpi_pm clocksource has been installed.
usbcore: deregistering interface driver usbhid
usbcore: deregistering interface driver hiddev
usbhid: Unknown parameter `debug'
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usbcore: deregistering interface driver usbhid
usbcore: deregistering interface driver hiddev
usbhid: Unknown parameter `debug'
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 4 low speed --> companion
ohci_hcd 0000:00:0b.0: auto-wakeup root hub
ehci_hcd 0000:00:0b.1: GetStatus port 4 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0010
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [3] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 4, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [3] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-4: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [3] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-4: config 1 has an invalid interface number: 1 but max is 0
usb 2-4: config 1 has 2 interfaces, different from the descriptor's value: 1
usb 2-4: skipped 1 descriptor after interface
usb 2-4: skipped 1 descriptor after interface
usb 2-4: default language 0x0409
usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-4: Product: USB Portable Keyboard
usb 2-4: Manufacturer: HOLTEK
usb 2-4: uevent
usb 2-4: usb_probe_device
usb 2-4: configuration #1 chosen from 1 choice
usb 2-4: adding 2-4:1.0 (config #1, interface 0)
usb 2-4:1.0: uevent
usb 2-4:1.0: uevent
usbhid 2-4:1.0: usb_probe_interface
usbhid 2-4:1.0: usb_probe_interface - got id
input: HOLTEK USB Portable Keyboard as /class/input/input5
input: USB HID v1.10 Keyboard [HOLTEK USB Portable Keyboard] on usb-0000:00:0b.0-4
usb 2-4: adding 2-4:1.1 (config #1, interface 1)
usb 2-4:1.1: uevent
usb 2-4:1.1: uevent
usbhid 2-4:1.1: usb_probe_interface
usbhid 2-4:1.1: usb_probe_interface - got id
input: HOLTEK USB Portable Keyboard as /class/input/input6
input: USB HID v1.10 Keyboard [HOLTEK USB Portable Keyboard] on usb-0000:00:0b.0-4
kobject_add failed for usbdev2.2_ep81 with -EEXIST, don't try to register things with the same name in the same directory.

Call Trace:
 [<ffffffff803a244c>] kobject_shadow_add+0x16e/0x1a2
 [<ffffffff80405ff1>] device_add+0xb1/0x5fb
 [<ffffffff803a21e7>] kobject_get+0x12/0x17
 [<ffffffff8800b81b>] :usbcore:usb_create_ep_files+0x231/0x2de
 [<ffffffff8800b026>] :usbcore:usb_create_sysfs_intf_files+0xaf/0xc8
 [<ffffffff880077b6>] :usbcore:usb_set_configuration+0x4fa/0x545
 [<ffffffff8800eaaf>] :usbcore:generic_probe+0x1ae/0x1fb
 [<ffffffff8040832e>] __device_attach+0x0/0x5
 [<ffffffff804082a5>] driver_probe_device+0xf6/0x17f
 [<ffffffff8040832e>] __device_attach+0x0/0x5
 [<ffffffff80407562>] bus_for_each_drv+0x40/0x72
 [<ffffffff804083b9>] device_attach+0x63/0x7a
 [<ffffffff804074d6>] bus_attach_device+0x2a/0x76
 [<ffffffff804062c6>] device_add+0x386/0x5fb
 [<ffffffff880021e1>] :usbcore:usb_new_device+0x133/0x170
 [<ffffffff88003aa2>] :usbcore:hub_thread+0x9cc/0xe7f
 [<ffffffff802460c2>] autoremove_wake_function+0x0/0x2e
 [<ffffffff880030d6>] :usbcore:hub_thread+0x0/0xe7f
 [<ffffffff80245fa8>] kthread+0x47/0x73
 [<ffffffff8020cc88>] child_rip+0xa/0x12
 [<ffffffff80245f61>] kthread+0x0/0x73
 [<ffffffff8020cc7e>] child_rip+0x0/0x12

drivers/usb/core/inode.c: creating file '002'
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [3] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 4, status 0300, change 0003, 1.5 Mb/s
usb 2-4: USB disconnect, address 2
usb 2-4: unregistering device
usb 2-4: usb_disable_device nuking all URBs
ohci_hcd 0000:00:0b.0: shutdown urb ffff810016b248c0 pipe 40408280 ep1in-intr
ohci_hcd 0000:00:0b.0: shutdown urb ffff810016b244c0 pipe 40408280 ep1in-intr
usb 2-4: unregistering interface 2-4:1.0
usb_endpoint usbdev2.2_ep81: ep_device_release called for usbdev2.2_ep81
usb 2-4:1.0: uevent
usb 2-4:1.0: uevent
usb 2-4: unregistering interface 2-4:1.1
usb 2-4:1.1: uevent
usb 2-4:1.1: uevent
usb_endpoint usbdev2.2_ep00: ep_device_release called for usbdev2.2_ep00
usb 2-4: uevent
hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x300
ohci_hcd 0000:00:0b.0: auto-stop root hub