MSI rs480m2 system will not boot when either acpi or apic are enabled in the boot arguments. This has been tested in many kernels (gentoo and vanilla) up and including 2.6.16-rc1. The info here is from the 2.6.16-rc1 kernel 1) When booting with command line root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 noapictimer the following is a screenshot of what happens. First it pauses at "sata_sil" and then http://img66.imageshack.us/img66/2489/screenacpismall4my.jpg 2) When booting with commmand line root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 acpi=off the following is a screenshot of what happens. http://img204.imageshack.us/img204/9753/screenapicsmall5tx.jpg The output of dmesg when on a successful boot with acpi off and noapictimer is ---------------------- dmesg ---------------------------------------- Bootdata ok (command line is root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 noapictimer no_timer_check acpi=off) Linux version 2.6.16-rc1 (root@localhost) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #1 Sat Jan 21 14:56:38 GM T 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bef0000 (usable) BIOS-e820: 000000003bef0000 - 000000003bef3000 (ACPI NVS) BIOS-e820: 000000003bef3000 - 000000003bf00000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) On node 0 totalpages: 240915 DMA zone: 2823 pages, LIFO batch:0 DMA32 zone: 238092 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: OEM00000 <6>Product ID: PROD00000000 <6>APIC at: 0xFEE00000 Processor #0 6:8 APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Setting APIC routing to flat Processors: 1 Allocating PCI resources starting at 40000000 (gap: 3bf00000:a4100000) Checking aperture... CPU 0: aperture @ 258a000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Built 1 zonelists Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 noapictimer no_timer _check acpi=off Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 1790.870 MHz processor. time.c: Using PIT/TSC based timekeeping. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) PCI-DMA: Disabling IOMMU. Memory: 960000k/981952k available (2786k kernel code, 21036k reserved, 1087k data, 200k init) Calibrating delay using timer specific routine.. 3589.36 BogoMIPS (lpj=7178725) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) mtrr: v2.0 (20020519) CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00 Disabling APIC timer testing NMI watchdog ... OK. checking if image is initramfs... it is Freeing initrd memory: 1433k freed DMI 2.4 present. NET: Registered protocol family 16 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter disabled. SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 PCI: Cannot allocate resource region 3 of device 0000:00:00.0 TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: fdd00000-fddfffff PREFETCH window: d8000000-dfffffff PCI: Bridge: 0000:00:14.4 IO window: d000-dfff MEM window: fdc00000-fdcfffff PREFETCH window: fde00000-fdefffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 JFS: nTxBlock = 7515, nTxLock = 60122 SGI XFS with ACLs, large block/inode numbers, no debug enabled Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered time.c: Lost 2 timer tick(s)! rip msleep+0x3/0x3a) time.c: Lost 2 timer tick(s)! rip msleep+0x3/0x3a) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... spurious 8259A interrupt: IRQ7. hda: BENQ DVD DD DW1640, ATAPI CD/DVD-ROM drive Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 94X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: generic_sse generic_sse: 5463.000 MB/sec raid5: using function: generic_sse (5463.000 MB/sec) raid6: int64x1 1668 MB/s raid6: int64x2 2081 MB/s raid6: int64x4 2231 MB/s raid6: int64x8 1629 MB/s raid6: sse2x1 2206 MB/s raid6: sse2x2 2918 MB/s raid6: sse2x4 3347 MB/s raid6: using algorithm sse2x4 (3347 MB/s) md: raid6 personality registered for level 6 md: multipath personality registered for level -4 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.0) powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV) cpu_init done, current fid 0xa, vid 0x6 BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 200k freed ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 10, io mem 0xfe02b000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected input: AT Translated Set 2 keyboard as /class/input/input0 usb 1-7: new high speed USB device using ehci_hcd and address 4 usb 1-7: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning USB Universal Host Controller Interface driver v2.3 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 10, io mem 0xfe02d000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 10, io mem 0xfe02c000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected libata version 1.20 loaded. sata_sil 0000:00:11.0: version 0.9 ata1: SATA max UDMA/100 cmd 0xFFFFC20000550080 ctl 0xFFFFC2000055008A bmdma 0xFFFFC20000550000 irq 10 ata2: SATA max UDMA/100 cmd 0xFFFFC200005500C0 ctl 0xFFFFC200005500CA bmdma 0xFFFFC20000550008 irq 10 ata1: SATA link down (SStatus 0) scsi1 : sata_sil ata2: SATA link down (SStatus 0) scsi2 : sata_sil ata3: SATA max UDMA/100 cmd 0xFFFFC20000552080 ctl 0xFFFFC2000055208A bmdma 0xFFFFC20000552000 irq 11 ata4: SATA max UDMA/100 cmd 0xFFFFC200005520C0 ctl 0xFFFFC200005520CA bmdma 0xFFFFC20000552008 irq 11 ata3: SATA link up 1.5 Gbps (SStatus 113) usb 2-3: new full speed USB device using ohci_hcd and address 2 ata3: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:3c01 87:4023 88:40ff ata3: dev 0 ATA-7, max UDMA7, 390721968 sectors: LBA48 ata3: dev 0 configured for UDMA/100 scsi3 : sata_sil usb 2-3: configuration #1 chosen from 1 choice ata4: SATA link down (SStatus 0) scsi4 : sata_sil Vendor: ATA Model: SAMSUNG SP2004C Rev: VM10 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 < sda5<6>usb 3-1: new low speed USB device using ohci_hcd and address 2 sda6 > sda4 sd 3:0:0:0: Attached scsi disk sda sd 3:0:0:0: Attached scsi generic sg0 type 0 usb 3-1: configuration #1 chosen from 1 choice input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.1-1 ReiserFS: sda5: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda5 kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. Vendor: USB2.0 Model: CF CardReader Rev: Type: Direct-Access ANSI SCSI revision: 00 sd 0:0:0:0: Attached scsi removable disk sdb sd 0:0:0:0: Attached scsi generic sg1 type 0 Vendor: USB2.0 Model: CBO CardReader Rev: Type: Direct-Access ANSI SCSI revision: 00 sd 0:0:0:1: Attached scsi removable disk sdc sd 0:0:0:1: Attached scsi generic sg2 type 0 usb-storage: device scan complete Adding 2811332k swap on /dev/sda6. Priority:-1 extents:1 across:2811332k EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda5, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver 2.1.25 [Flags: R/O MODULE]. NTFS volume version 3.1. time.c: Lost 13 timer tick(s)! rip 0x444b50) 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0xffffc200006e2000, 00:13:d3:2e:29:c6, IRQ 5 eth0: Identified 8139 chip type 'RTL-8100B/8139D' time.c: Lost 15 timer tick(s)! rip default_idle+0x2a/0x52) time.c: Lost 12 timer tick(s)! rip 0x423282) eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 smsc47m1: Found SMSC LPC47M15x/LPC47M192/LPC47M997 Driver 'smsc47m1' needs updating - please use bus_type methods time.c: Lost 15 timer tick(s)! rip default_idle+0x2a/0x52) eth0: no IPv6 routers present time.c: Lost 13 timer tick(s)! rip 0x2ae0f4203435) time.c: Lost 14 timer tick(s)! rip default_idle+0x2a/0x52) ------------ lspci ------------------ lspci 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc Unknown device 5a3f 00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller 00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 04) 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge 00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS480 [Radeon Xpress 200G Series] 02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 02:04.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) -------------------------------------------------------------------
A litte more investigation shows that the system will in fact boot with Command line root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 noapictimer acpi=noirq (NOTE acpi=noirq instead of acpi=off and the ACPI entries in dmesg now) Dmesg is now... Bootdata ok (command line is root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 noapictimer acpi=noirq) Linux version 2.6.16-rc1 (root@localhost) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #1 Sat Jan 21 14:56:38 GMT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bef0000 (usable) BIOS-e820: 000000003bef0000 - 000000003bef3000 (ACPI NVS) BIOS-e820: 000000003bef3000 - 000000003bf00000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) ACPI: RSDP (v000 RS480 ) @ 0x00000000000f8070 ACPI: RSDT (v001 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003bef3040 ACPI: FADT (v002 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003bef30c0 ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000003bef69c0 ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x000000003bef6ac0 ACPI: MCFG (v001 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003bef6bc0 ACPI: MADT (v001 RS480 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003bef6900 ACPI: DSDT (v001 RS480 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000 On node 0 totalpages: 240915 DMA zone: 2823 pages, LIFO batch:0 DMA32 zone: 238092 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) Using ACPI for processor (LAPIC) configuration information Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: OEM00000 <6>Product ID: PROD00000000 <6>APIC at: 0xFEE00000 I/O APIC #2 Version 17 at 0xFEC00000. Setting APIC routing to flat Processors: 1 Allocating PCI resources starting at 40000000 (gap: 3bf00000:a4100000) Checking aperture... CPU 0: aperture @ 258a000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Built 1 zonelists Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/sda5 udev report_lost_ticks=100 noapictimer acpi=noirq Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 1790.915 MHz processor. time.c: Using PIT/TSC based timekeeping. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) PCI-DMA: Disabling IOMMU. Memory: 960000k/981952k available (2786k kernel code, 21036k reserved, 1087k data, 200k init) Calibrating delay using timer specific routine.. 3588.73 BogoMIPS (lpj=7177479) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) mtrr: v2.0 (20020519) CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00 ACPI: setting ELCR to 0e28 (from 0c28) time.c: Lost 1 timer tick(s)! rip acpi_os_write_port+0x1a/0x34) Disabling APIC timer testing NMI watchdog ... OK. checking if image is initramfs... it is Freeing initrd memory: 1433k freed DMI 2.4 present. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Cannot allocate resource region 3 of device 0000:00:00.0 TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: fdd00000-fddfffff PREFETCH window: d8000000-dfffffff PCI: Bridge: 0000:00:14.4 IO window: d000-dfff MEM window: fdc00000-fdcfffff PREFETCH window: fde00000-fdefffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 JFS: nTxBlock = 7515, nTxLock = 60122 SGI XFS with ACLs, large block/inode numbers, no debug enabled Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered time.c: Lost 2 timer tick(s)! rip msleep+0x3/0x3a) time.c: Lost 2 timer tick(s)! rip msleep+0x3/0x3a) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 acpiphp_glue: can't get bus number, assuming 0 ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Processor [CPU0] (supports 8 throttling states) ibm_acpi: ec object not found Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hda: BENQ DVD DD DW1640, ATAPI CD/DVD-ROM drive Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 94X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 usbmon: debugfs is not available mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: generic_sse generic_sse: 5464.000 MB/sec raid5: using function: generic_sse (5464.000 MB/sec) raid6: int64x1 1668 MB/s raid6: int64x2 2082 MB/s raid6: int64x4 2164 MB/s raid6: int64x8 1636 MB/s raid6: sse2x1 2189 MB/s raid6: sse2x2 2912 MB/s raid6: sse2x4 3341 MB/s raid6: using algorithm sse2x4 (3341 MB/s) md: raid6 personality registered for level 6 md: multipath personality registered for level -4 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.0) powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV) powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) cpu_init done, current fid 0xa, vid 0x6 ACPI wakeup devices: PCI0 USB0 USB1 USB2 AUDO P2P MAC ACPI: (supports S0 S1 S3 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 200k freed ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 10, io mem 0xfe02b000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected input: AT Translated Set 2 keyboard as /class/input/input0 usb 1-7: new high speed USB device using ehci_hcd and address 3 usb 1-7: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning USB Universal Host Controller Interface driver v2.3 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 10, io mem 0xfe02d000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 10, io mem 0xfe02c000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected libata version 1.20 loaded. sata_sil 0000:00:11.0: version 0.9 ata1: SATA max UDMA/100 cmd 0xFFFFC2000002E080 ctl 0xFFFFC2000002E08A bmdma 0xFFFFC2000002E000 irq 10 ata2: SATA max UDMA/100 cmd 0xFFFFC2000002E0C0 ctl 0xFFFFC2000002E0CA bmdma 0xFFFFC2000002E008 irq 10 ata1: SATA link down (SStatus 0) scsi1 : sata_sil ata2: SATA link down (SStatus 0) scsi2 : sata_sil ata3: SATA max UDMA/100 cmd 0xFFFFC20000030080 ctl 0xFFFFC2000003008A bmdma 0xFFFFC20000030000 irq 11 ata4: SATA max UDMA/100 cmd 0xFFFFC200000300C0 ctl 0xFFFFC200000300CA bmdma 0xFFFFC20000030008 irq 11 ata3: SATA link up 1.5 Gbps (SStatus 113) usb 3-1: new low speed USB device using ohci_hcd and address 2 ata3: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7468 86:3c01 87:4023 88:40ff ata3: dev 0 ATA-7, max UDMA7, 390721968 sectors: LBA48 ata3: dev 0 configured for UDMA/100 scsi3 : sata_sil usb 3-1: configuration #1 chosen from 1 choice input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input1 input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.1-1 ata4: SATA link down (SStatus 0) scsi4 : sata_sil Vendor: ATA Model: SAMSUNG SP2004C Rev: VM10 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 < sda5 sda6 > sda4 sd 3:0:0:0: Attached scsi disk sda sd 3:0:0:0: Attached scsi generic sg0 type 0 ReiserFS: sda5: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda5 kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. Vendor: USB2.0 Model: CF CardReader Rev: Type: Direct-Access ANSI SCSI revision: 00 sd 0:0:0:0: Attached scsi removable disk sdb sd 0:0:0:0: Attached scsi generic sg1 type 0 Vendor: USB2.0 Model: CBO CardReader Rev: Type: Direct-Access ANSI SCSI revision: 00 sd 0:0:0:1: Attached scsi removable disk sdc sd 0:0:0:1: Attached scsi generic sg2 type 0 usb-storage: device scan complete Adding 2811332k swap on /dev/sda6. Priority:-1 extents:1 across:2811332k EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda5, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver 2.1.25 [Flags: R/O MODULE]. NTFS volume version 3.1. 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0xffffc20000066000, 00:13:d3:2e:29:c6, IRQ 5 eth0: Identified 8139 chip type 'RTL-8100B/8139D' eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 smsc47m1: Found SMSC LPC47M15x/LPC47M192/LPC47M997 Driver 'smsc47m1' needs updating - please use bus_type methods time.c: Lost 14 timer tick(s)! rip default_idle+0x2a/0x52) eth0: no IPv6 routers present time.c: Lost 13 timer tick(s)! rip default_idle+0x2a/0x52) time.c: Lost 15 timer tick(s)! rip default_idle+0x2a/0x52) time.c: Lost 13 timer tick(s)! rip 0x9a63fe) time.c: Lost 15 timer tick(s)! rip default_idle+0x2a/0x52) Raphae
In future, please use the attachment feature to post large text files. Are you running the most recent BIOS revision for your system?
Sorry about the (lack of ) attachments. BIOS is the latest version which is 3.80. Raphael
Please file this as an upstream bug at http://bugzilla.kernel.org and post the new bug URL here.
Created attachment 77744 [details] dmidecode output
Created attachment 77747 [details] output of lspci -vv
Reported upstream at http://bugzilla.kernel.org/show_bug.cgi?id=5933 Raphael
The system boots now with the latest kernels. Closing bug.
