New dmesg (might be handy)

Dmesg (text/plain), 15.02 KB, created by VeXocide on 2006-03-06 09:26:52 UTC

ies: 65536 (order: 6, 262144 bytes)
Memory: 1030648k/1047360k available (3675k kernel code, 15932k reserved, 1074k data, 220k init, 129856k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3729.17 BogoMIPS (lpj=1864586)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 1611k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd920, last bus=7
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 9) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *11)
ACPI: Embedded Controller [EC0] (gpe 28)
ACPI: Power Resource [QFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
PCI: Bridge: 0000:00:01.0
  IO window: 6000-6fff
  MEM window: c8100000-c81fffff
  PREFETCH window: d0000000-d7ffffff
PCI: Bus 7, cardbus bridge: 0000:06:01.0
  IO window: 00007400-000074ff
  IO window: 00007800-000078ff
  PREFETCH window: 50000000-51ffffff
  MEM window: 54000000-55ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 7000-7fff
  MEM window: c8200000-c82fffff
  PREFETCH window: 50000000-52ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 16 (level, low) -> IRQ 16
Simple Boot Flag at 0x35 set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1141661726.269:1): initialized
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 [e-mail]).
NTFS driver 2.1.25 [Flags: R/W].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
vesafb: unrecognized option mtrr
vesafb: ATI Technologies Inc., P22 , 01.00 (OEM: ATI MOBILITY RADEON X300   )
vesafb: VBE version: 2.0
vesafb: protected mode interface info at c000:576f
vesafb: pmi: set display start = c00c57dd, set palette = c00c5817
vesafb: pmi: ports = 6010 6016 6054 6038 603c 605c 6000 6004 60b0 60b2 60b4 
vesafb: no monitor limits have been set
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=2800
Console: switching to colour frame buffer device 175x65
fbsplash: console 0 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 0
vesafb: framebuffer at 0xd0000000, mapped to 0xf8900000, using 11484k, total 65536k
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [ACAD] (off-line)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (off)
ACPI: Video Device [GFX0] (multi-head: yes  rom: yes  post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (40 C)
PNP: PS/2 Controller [PNP0303:KBCE,PNP0f13:MSEE] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) -> IRQ 17
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 19 (level, low) -> IRQ 18
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xf880e000, 00:c0:9f:a3:90:d5, IRQ 18
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 19
ICH6: chipset revision 4
ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x48c0-0x48c7, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HTS541080G9AT00, ATA DISK drive
hdb: PHILIPS DVD+/-RW SDVD8441, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 > hda3
hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
ohci1394: $Rev: 1313 $ Ben Collins <[e-mail]>
ACPI: PCI Interrupt 0000:06:01.1[B] -> GSI 17 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[c8204800-c8204fff]  Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:06:01.0 [1631:c00b]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:01.0, mfunc 0x01021b22, devctl 0x66
Yenta: ISA IRQ mask 0x0c78, PCI irq 16
Socket status: 30000086
pcmcia: parent PCI bridge I/O window: 0x7000 - 0x7fff
cs: IO port probe 0x7000-0x7fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc8200000 - 0xc82fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x52ffffff
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xc8000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 21, io base 0x00004800
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 18, io base 0x00004820
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 19, io base 0x00004840
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004860
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00004ce047a390d5]
usb 5-1: new full speed USB device using uhci_hcd and address 2
usb 5-2: new full speed USB device using uhci_hcd and address 3
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver touchkitusb
usbcore: registered new driver cytherm
drivers/usb/misc/cytherm.c: v1.0:Cypress USB Thermometer driver
usbcore: registered new driver phidgetservo
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.4 (8182 buckets, 65456 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <[e-mail]>.  http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
ACPI wakeup devices: 
LID0 LANC MODM 
ACPI: (supports S0 S3 S4 S5)
Suspend2 2.2: Swapwriter: Signature found.
Suspend2 2.2: Suspending enabled.
ReiserFS: hda6: found reiserfs format "3.6" with standard journal
ReiserFS: hda6: using ordered data mode
ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda6: checking transaction log (hda6)
ReiserFS: hda6: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
Adding 1052216k swap on /dev/hda7.  Priority:-1 extents:1 across:1052216k
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, 1.1.12
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[e-mail]>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.0
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:06:03.0[A] -> GSI 18 (level, low) -> IRQ 19
ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
ipw2200: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.
ipw2200: Detected geography ZZA (11 802.11bg channels, 13 802.11a channels)
fuse init (API version 7.5)
fuse distribution version: 2.5.2
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 50996 usecs
intel8x0: clocking to 48000
cdrom: open failed.
fbsplash: console 1 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 1
fbsplash: console 2 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 2
fbsplash: console 3 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 3
fbsplash: console 4 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 4
fbsplash: console 5 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 5
fbsplash: console 7 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 7
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 926 MBytes.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[fglrx] module loaded - fglrx 8.22.5 [Feb  7 2006] on minor 0
[fglrx] free  PCIe = 54804480
[fglrx] max   PCIe = 54804480
[fglrx] free  LFB = 47099904
[fglrx] max   LFB = 47099904
[fglrx] free  Inv = 0
[fglrx] max   Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB  = 0
[fglrx] total PCIe = 16384
ieee80211_crypt: registered algorithm 'WEP'
[fglrx] free  PCIe = 54804480
[fglrx] max   PCIe = 54804480
[fglrx] free  LFB = 47099904
[fglrx] max   LFB = 47099904
[fglrx] free  Inv = 0
[fglrx] max   Inv = 0
[fglrx] total Inv = 0
[fglrx] total TIM = 0
[fglrx] total FB  = 0
[fglrx] total PCIe = 16384
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
[fglrx] Flat panel plugged in
usb 2-2: new low speed USB device using uhci_hcd and address 2
input: Microsoft Basic Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.0-2
ipw2200: Firmware error detected.  Restarting.
ipw2200: Sysfs 'error' log captured.