Linux version 2.6.32.3 (root@albatros2) (gcc version 4.3.4 (Gentoo 4.3.4 p1.0, pie-10.1.5) ) #2 SMP Wed Jan 13 12:05:53 EET 2010 Command line: KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000099c00 (usable) BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000bff10000 (usable) BIOS-e820: 00000000bff10000 - 00000000bff21000 (ACPI data) BIOS-e820: 00000000bff21000 - 00000000bff80000 (ACPI NVS) BIOS-e820: 00000000bff80000 - 00000000c0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) DMI present. last_pfn = 0xbff10 max_arch_pfn = 0x400000000 MTRR default type: uncachable MTRR fixed ranges enabled: 00000-9FFFF write-back A0000-BFFFF uncachable C0000-CFFFF write-protect D0000-DFFFF uncachable E0000-FFFFF write-protect MTRR variable ranges enabled: 0 base 000000000 mask F80000000 write-back 1 base 080000000 mask FC0000000 write-back 2 base 0BFF80000 mask FFFF80000 uncachable 3 disabled 4 disabled 5 disabled 6 disabled 7 disabled x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 initial memory mapped : 0 - 20000000 init_memory_mapping: 0000000000000000-00000000bff10000 0000000000 - 00bfe00000 page 2M 00bfe00000 - 00bff10000 page 4k kernel direct mapping tables up to bff10000 @ 8000-d000 (6 early reservations) ==> bootmem [0000000000 - 00bff10000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0001000000 - 00018055a4] TEXT DATA BSS ==> [0001000000 - 00018055a4] #3 [0000099c00 - 0000100000] BIOS reserved ==> [0000099c00 - 0000100000] #4 [0001806000 - 00018061f8] BRK ==> [0001806000 - 00018061f8] #5 [0000008000 - 000000b000] PGTABLE ==> [0000008000 - 000000b000] found SMP MP-table at [ffff8800000f6f90] f6f90 [ffffea0000000000-ffffea00029fffff] PMD -> [ffff880001e00000-ffff8800047fffff] on node 0 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00100000 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x00000099 0: 0x00000100 -> 0x000bff10 On node 0 totalpages: 786089 DMA zone: 56 pages used for memmap DMA zone: 108 pages reserved DMA zone: 3829 pages, LIFO batch:0 DMA32 zone: 10693 pages used for memmap DMA32 zone: 771403 pages, LIFO batch:31 Intel MultiProcessor Specification v1.4 MPTABLE: OEM ID: INTEL MPTABLE: Product ID: Bridge CRB MPTABLE: APIC at: 0xFEE00000 Processor #0 (Bootup-CPU) Processor #6 Processor #1 Processor #7 I/O APIC #2 Version 32 at 0xFEC00000. I/O APIC #3 Version 32 at 0xFEC80000. Processors: 4 SMP: Allowing 4 CPUs, 0 hotplug CPUs nr_irqs_gsi: 48 Allocating PCI resources starting at c0000000 (gap: c0000000:20000000) NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1 PERCPU: Embedded 24 pages/cpu @ffff880001a00000 s68632 r8192 d21480 u524288 pcpu-alloc: s68632 r8192 d21480 u524288 alloc=1*2097152 pcpu-alloc: [0] 0 1 2 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 775232 Kernel command line: PID hash table entries: 4096 (order: 3, 32768 bytes) Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Initializing CPU#0 Checking aperture... No AGP bridge found Memory: 3085760k/3144768k available (4682k kernel code, 412k absent, 57948k reserved, 2258k data, 408k init) Hierarchical RCU implementation. NR_IRQS:1280 Console: colour VGA+ 80x25 console [tty0] enabled Fast TSC calibration using PIT Detected 1596.073 MHz processor. Calibrating delay loop (skipped), value calculated using timer frequency.. 3192.14 BogoMIPS (lpj=15960730) Security Framework initialized Mount-cache hash table entries: 256 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 mce: CPU supports 6 MCE banks CPU0: Thermal monitoring enabled (TM2) using mwait in idle threads. Freeing SMP alternatives: 38k freed Setting APIC routing to flat ExtINT not setup in hardware but reported by MP table ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0 CPU0: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 Booting processor 1 APIC 0x6 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3191.99 BogoMIPS (lpj=15959959) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 3 CPU: Processor Core ID: 0 CPU1: Thermal monitoring enabled (TM2) CPU1: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Booting processor 2 APIC 0x1 ip 0x6000 Initializing CPU#2 Calibrating delay using timer specific routine.. 3192.02 BogoMIPS (lpj=15960110) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU2: Thermal monitoring enabled (TM2) CPU2: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#2]: passed. Booting processor 3 APIC 0x7 ip 0x6000 Initializing CPU#3 Calibrating delay using timer specific routine.. 3191.97 BogoMIPS (lpj=15959889) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 3 CPU: Processor Core ID: 1 CPU3: Thermal monitoring enabled (TM2) CPU3: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 checking TSC synchronization [CPU#0 -> CPU#3]: passed. Brought up 4 CPUs Total of 4 processors activated (12768.13 BogoMIPS). NET: Registered protocol family 16 PCI: Using configuration type 1 for base access bio: create slab at 0 vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:02.0: PME# supported from D0 D3hot D3cold pci 0000:00:02.0: PME# disabled pci 0000:00:03.0: PME# supported from D0 D3hot D3cold pci 0000:00:03.0: PME# disabled pci 0000:00:04.0: PME# supported from D0 D3hot D3cold pci 0000:00:04.0: PME# disabled pci 0000:00:05.0: PME# supported from D0 D3hot D3cold pci 0000:00:05.0: PME# disabled pci 0000:00:06.0: PME# supported from D0 D3hot D3cold pci 0000:00:06.0: PME# disabled pci 0000:00:07.0: PME# supported from D0 D3hot D3cold pci 0000:00:07.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold pci 0000:00:1c.1: PME# disabled pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f] pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f] pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f] pci 0000:00:1d.3: reg 20 io port: [0x1860-0x187f] pci 0000:00:1d.7: reg 10 32bit mmio: [0xdff00000-0xdff003ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03] pci 0000:00:1f.1: reg 20 io port: [0x1880-0x188f] pci 0000:00:1f.2: reg 10 io port: [0x18c0-0x18c7] pci 0000:00:1f.2: reg 14 io port: [0x1894-0x1897] pci 0000:00:1f.2: reg 18 io port: [0x1898-0x189f] pci 0000:00:1f.2: reg 1c io port: [0x1890-0x1893] pci 0000:00:1f.2: reg 20 io port: [0x18a0-0x18bf] pci 0000:00:1f.2: reg 24 32bit mmio: [0xdff00400-0xdff007ff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: reg 20 io port: [0x18e0-0x18ff] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold pci 0000:01:00.0: PME# disabled pci 0000:01:00.3: PME# supported from D0 D3hot D3cold pci 0000:01:00.3: PME# disabled pci 0000:00:02.0: bridge 32bit mmio: [0xdf900000-0xdf9fffff] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:10:00.0: reg 10 64bit mmio: [0xdfb01000-0xdfb01fff] pci 0000:10:00.0: reg 18 64bit mmio: [0xdfb00000-0xdfb000ff] pci 0000:10:00.0: reg 20 io port: [0x2000-0x20ff] pci 0000:10:00.0: reg 30 32bit mmio pref: [0x000000-0x03ffff] pci 0000:00:04.0: bridge io port: [0x2000-0x2fff] pci 0000:00:04.0: bridge 32bit mmio: [0xdfb00000-0xdfbfffff] pci 0000:1e:00.0: reg 10 64bit mmio: [0xdfa00000-0xdfa0ffff] pci 0000:1e:00.0: PME# supported from D3hot D3cold pci 0000:1e:00.0: PME# disabled pci 0000:00:1c.0: bridge 32bit mmio: [0xdfa00000-0xdfafffff] pci 0000:1f:00.0: reg 10 64bit mmio: [0xdfc00000-0xdfc0ffff] pci 0000:1f:00.0: PME# supported from D3hot D3cold pci 0000:1f:00.0: PME# disabled pci 0000:00:1c.1: bridge 32bit mmio: [0xdfc00000-0xdfcfffff] pci 0000:20:02.0: reg 10 32bit mmio pref: [0xde000000-0xdeffffff] pci 0000:20:02.0: reg 14 32bit mmio: [0xdf800000-0xdf803fff] pci 0000:20:02.0: reg 18 32bit mmio: [0xdf000000-0xdf7fffff] pci 0000:20:02.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] pci 0000:00:1e.0: transparent bridge pci 0000:00:1e.0: bridge 32bit mmio: [0xdf000000-0xdf8fffff] pci 0000:00:1e.0: bridge 64bit mmio pref: [0xde000000-0xdeffffff] vgaarb: device added: PCI:0000:20:02.0,decodes=io+mem,owns=io+mem,locks=none PCI: Discovered primary peer bus 05 [IRQ] pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:2670] hpet clockevent registered HPET: 3 timers in total, 0 timers will be used for per-cpu timer Switching to clocksource tsc pci 0000:02:00.0: PCI bridge, secondary bus 0000:03 pci 0000:02:00.0: IO window: disabled pci 0000:02:00.0: MEM window: disabled pci 0000:02:00.0: PREFETCH window: disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled pci 0000:01:00.3: PCI bridge, secondary bus 0000:0b pci 0000:01:00.3: IO window: disabled pci 0000:01:00.3: MEM window: disabled pci 0000:01:00.3: PREFETCH window: disabled pci 0000:00:02.0: PCI bridge, secondary bus 0000:01 pci 0000:00:02.0: IO window: disabled pci 0000:00:02.0: MEM window: 0xdf900000-0xdf9fffff pci 0000:00:02.0: PREFETCH window: disabled pci 0000:00:03.0: PCI bridge, secondary bus 0000:0c pci 0000:00:03.0: IO window: disabled pci 0000:00:03.0: MEM window: disabled pci 0000:00:03.0: PREFETCH window: disabled pci 0000:00:04.0: PCI bridge, secondary bus 0000:10 pci 0000:00:04.0: IO window: 0x2000-0x2fff pci 0000:00:04.0: MEM window: 0xdfb00000-0xdfbfffff pci 0000:00:04.0: PREFETCH window: 0xc0000000-0xc00fffff pci 0000:00:05.0: PCI bridge, secondary bus 0000:11 pci 0000:00:05.0: IO window: disabled pci 0000:00:05.0: MEM window: disabled pci 0000:00:05.0: PREFETCH window: disabled pci 0000:00:06.0: PCI bridge, secondary bus 0000:12 pci 0000:00:06.0: IO window: disabled pci 0000:00:06.0: MEM window: disabled pci 0000:00:06.0: PREFETCH window: disabled pci 0000:00:07.0: PCI bridge, secondary bus 0000:13 pci 0000:00:07.0: IO window: disabled pci 0000:00:07.0: MEM window: disabled pci 0000:00:07.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI bridge, secondary bus 0000:1e pci 0000:00:1c.0: IO window: 0x3000-0x3fff pci 0000:00:1c.0: MEM window: 0xdfa00000-0xdfafffff pci 0000:00:1c.0: PREFETCH window: 0x000000c0100000-0x000000c02fffff pci 0000:00:1c.1: PCI bridge, secondary bus 0000:1f pci 0000:00:1c.1: IO window: 0x4000-0x4fff pci 0000:00:1c.1: MEM window: 0xdfc00000-0xdfcfffff pci 0000:00:1c.1: PREFETCH window: 0x000000c0300000-0x000000c04fffff pci 0000:00:1e.0: PCI bridge, secondary bus 0000:20 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: 0xdf000000-0xdf8fffff pci 0000:00:1e.0: PREFETCH window: 0x000000de000000-0x000000deffffff pci 0000:00:02.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:00:02.0: setting latency timer to 64 pci 0000:01:00.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:01:00.0: setting latency timer to 64 pci 0000:02:00.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:02:00.0: setting latency timer to 64 pci 0000:01:00.3: setting latency timer to 64 pci 0000:00:03.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:00:03.0: setting latency timer to 64 pci 0000:00:04.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:00:04.0: setting latency timer to 64 pci 0000:00:05.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:00:05.0: setting latency timer to 64 pci 0000:00:06.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:00:06.0: setting latency timer to 64 pci 0000:00:07.0: can't find IRQ for PCI INT A; probably buggy MP table pci 0000:00:07.0: setting latency timer to 64 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] pci_bus 0000:01: resource 1 mem: [0xdf900000-0xdf9fffff] pci_bus 0000:10: resource 0 io: [0x2000-0x2fff] pci_bus 0000:10: resource 1 mem: [0xdfb00000-0xdfbfffff] pci_bus 0000:10: resource 2 pref mem [0xc0000000-0xc00fffff] pci_bus 0000:1e: resource 0 io: [0x3000-0x3fff] pci_bus 0000:1e: resource 1 mem: [0xdfa00000-0xdfafffff] pci_bus 0000:1e: resource 2 pref mem [0xc0100000-0xc02fffff] pci_bus 0000:1f: resource 0 io: [0x4000-0x4fff] pci_bus 0000:1f: resource 1 mem: [0xdfc00000-0xdfcfffff] pci_bus 0000:1f: resource 2 pref mem [0xc0300000-0xc04fffff] pci_bus 0000:20: resource 1 mem: [0xdf000000-0xdf8fffff] pci_bus 0000:20: resource 2 pref mem [0xde000000-0xdeffffff] pci_bus 0000:20: resource 3 io: [0x00-0xffff] pci_bus 0000:20: resource 4 mem: [0x000000-0xffffffffffffffff] pci_bus 0000:05: resource 0 io: [0x00-0xffff] pci_bus 0000:05: resource 1 mem: [0x000000-0xffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 pci 0000:20:02.0: Boot video device platform rtc_cmos: registered platform RTC device (no PNP device found) audit: initializing netlink socket (disabled) type=2000 audit(1263384798.790:1): initialized HugeTLB registered 2 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.29 [Flags: R/W]. fuse init (API version 7.13) SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled msgmni has been set to 6028 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) pcieport 0000:00:02.0: device [8086:25f7] has invalid IRQ; check vendor BIOS pcieport 0000:00:02.0: irq 48 for MSI/MSI-X pcieport 0000:00:02.0: setting latency timer to 64 pcieport 0000:00:03.0: device [8086:25e3] has invalid IRQ; check vendor BIOS pcieport 0000:00:03.0: irq 49 for MSI/MSI-X pcieport 0000:00:03.0: setting latency timer to 64 pcieport 0000:00:04.0: device [8086:25fa] has invalid IRQ; check vendor BIOS pcieport 0000:00:04.0: irq 50 for MSI/MSI-X pcieport 0000:00:04.0: setting latency timer to 64 pcieport 0000:00:05.0: device [8086:25e5] has invalid IRQ; check vendor BIOS pcieport 0000:00:05.0: irq 51 for MSI/MSI-X pcieport 0000:00:05.0: setting latency timer to 64 pcieport 0000:00:06.0: device [8086:25e6] has invalid IRQ; check vendor BIOS pcieport 0000:00:06.0: irq 52 for MSI/MSI-X pcieport 0000:00:06.0: setting latency timer to 64 pcieport 0000:00:07.0: device [8086:25e7] has invalid IRQ; check vendor BIOS pcieport 0000:00:07.0: irq 53 for MSI/MSI-X pcieport 0000:00:07.0: setting latency timer to 64 pcieport 0000:00:1c.0: irq 54 for MSI/MSI-X pcieport 0000:00:1c.0: setting latency timer to 64 pcieport 0000:00:1c.1: irq 55 for MSI/MSI-X pcieport 0000:00:1c.1: setting latency timer to 64 pcieport 0000:01:00.0: setting latency timer to 64 pcieport 0000:02:00.0: irq 56 for MSI/MSI-X pcieport 0000:02:00.0: setting latency timer to 64 Real Time Clock Driver v1.12b intel_rng: FWH not detected Linux agpgart interface v0.103 Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A brd: module loaded loop: module loaded nbd: registered device at major 43 Uniform Multi-Platform E-IDE driver piix 0000:00:1f.1: IDE controller (0x8086:0x269e rev 0x09) PIIX_IDE 0000:00:1f.1: PCI->APIC IRQ transform: INT A -> IRQ 19 piix 0000:00:1f.1: IDE port disabled piix 0000:00:1f.1: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1880-0x1887 Probing IDE interface ide0... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide-gd driver 1.18 ide-cd driver 5.00 ahci 0000:00:1f.2: version 3.0 ahci 0000:00:1f.2: PCI->APIC IRQ transform: INT B -> IRQ 19 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit pm led pmp slum part ahci 0000:00:1f.2: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 irq_stat 0x00000040, connection status changed ata2: SATA max UDMA/133 irq_stat 0x00000040, connection status changed ata3: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00600 irq 19 ata4: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00680 irq 19 ata5: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00700 irq 19 ata6: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00780 irq 19 Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI Copyright (c) 1999-2006 Intel Corporation. tg3.c:v3.102 (September 1, 2009) tg3 0000:1e:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16 tg3 0000:1e:00.0: setting latency timer to 64 eth0: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:1a:4b:a4:08:ce eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1]) eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] tg3 0000:1f:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17 tg3 0000:1f:00.0: setting latency timer to 64 eth1: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:1a:4b:a4:08:cf eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1]) eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] eth1: dma_rwctrl[76180000] dma_mask[64-bit] console [netcon0] enabled netconsole: network logging started ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: Enabling legacy PCI PM ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff00000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI->APIC IRQ transform: INT B -> IRQ 23 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 23, io base 0x00001820 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI->APIC IRQ transform: INT C -> IRQ 23 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 23, io base 0x00001840 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.3: PCI->APIC IRQ transform: INT D -> IRQ 23 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001860 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i8042.c: Warning: Keylock active. Failed to disable AUX port, but continuing anyway... Is this a SiS? If AUX port is really absent please use the 'i8042.noaux' option. ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice coretemp coretemp.0: Using relative temperature scale! coretemp coretemp.1: Using relative temperature scale! coretemp coretemp.2: Using relative temperature scale! coretemp coretemp.3: Using relative temperature scale! md: raid1 personality registered for level 1 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ctnetlink v0.93: registering with nfnetlink. IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller registered taskstats version 1 usb 4-1: new full speed USB device using uhci_hcd and address 2 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: FB080C4080, HPF0, max UDMA/100 ata2.00: ATA-7: FB080C4080, HPF0, max UDMA/100 ata2.00: 156301488 sectors, multi 0: LBA48 ata1.00: 156301488 sectors, multi 0: LBA48 ata2.00: configured for UDMA/100 ata1.00: configured for UDMA/100 scsi 0:0:0:0: Direct-Access ATA FB080C4080 n/a PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: scsi 1:0:0:0: Direct-Access ATA FB080C4080 n/a PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sda1 sda2 sda3 sda4 < sda5 sdb1 sdb2 sdb3 sdb4 < sda6 sdb5 sda7 > sd 0:0:0:0: [sda] Attached SCSI disk sdb6 sdb7 > sd 1:0:0:0: [sdb] Attached SCSI disk md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. usb 4-1: configuration #1 chosen from 1 choice input: ServerEngines SE USB Device as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input0 generic-usb 0003:0000:0000.0001: input: USB HID v1.11 Keyboard [ServerEngines SE USB Device] on usb-0000:00:1d.2-1/input0 input: ServerEngines SE USB Device as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input1 generic-usb 0003:0000:0000.0002: input: USB HID v1.11 Mouse [ServerEngines SE USB Device] on usb-0000:00:1d.2-1/input1 md: Scanned 10 and added 10 devices. md: autorun ... md: considering sdb7 ... md: adding sdb7 ... md: sdb6 has different UUID to sdb7 md: sdb5 has different UUID to sdb7 md: sdb3 has different UUID to sdb7 md: sdb1 has different UUID to sdb7 md: adding sda7 ... md: sda6 has different UUID to sdb7 md: sda5 has different UUID to sdb7 md: sda3 has different UUID to sdb7 md: sda1 has different UUID to sdb7 md: created md7 md: bind md: bind md: running: raid1: raid set md7 active with 2 out of 2 mirrors md7: detected capacity change from 0 to 45131956224 md: considering sdb6 ... md: adding sdb6 ... md: sdb5 has different UUID to sdb6 md: sdb3 has different UUID to sdb6 md: sdb1 has different UUID to sdb6 md: adding sda6 ... md: sda5 has different UUID to sdb6 md: sda3 has different UUID to sdb6 md: sda1 has different UUID to sdb6 md: created md6 md: bind md: bind md: running: raid1: raid set md6 active with 2 out of 2 mirrors md6: detected capacity change from 0 to 2056192000 md: considering sdb5 ... md: adding sdb5 ... md: sdb3 has different UUID to sdb5 md: sdb1 has different UUID to sdb5 md: adding sda5 ... md: sda3 has different UUID to sdb5 md: sda1 has different UUID to sdb5 md: created md5 md: bind md: bind md: running: raid1: raid set md5 active with 2 out of 2 mirrors md5: detected capacity change from 0 to 20489043968 md: considering sdb3 ... md: adding sdb3 ... md: sdb1 has different UUID to sdb3 md: adding sda3 ... md: sda1 has different UUID to sdb3 md: created md3 md: bind md: bind md: running: raid1: raid set md3 active with 2 out of 2 mirrors md3: detected capacity change from 0 to 10248585216 md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md1 md: bind md: bind md: running: raid1: raid set md1 active with 2 out of 2 mirrors md1: detected capacity change from 0 to 41025536 md: ... autorun DONE. md3: unknown partition table kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) readonly on device 9:3. Freeing unused kernel memory: 408k freed Write protecting the kernel read-only data: 6252k udev: starting version 146 Emulex LightPulse Fibre Channel SCSI driver 8.3.4 Copyright(c) 2004-2009 Emulex. All rights reserved. Entering lpfc_pci_probe_one() Well inside lpfc_pci_probe_one_s3() lpfc 0000:10:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16 lpfc 0000:10:00.0: setting latency timer to 64 scsi6 : on PCI bus 10 device 00 irq 16 Got into lpfc_sli_enable_intr, which is for sli-3. Finished with MSI. Going into INTx in lpfc_sli_enable_intr() INTx setup. md5: md6: md7: md1: unknown partition table unknown partition table unknown partition table unknown partition table intr_mode is 0 and we are into the interrupt if, in lpfc_pci_probe_one_s3() Left setup in lpfc_pci_probe_one_s3 lpfc 0000:10:00.0: 0:1303 Link Up Event x1 received Data: x1 xf7 x10 x0 x0 x0 0 scsi 6:0:0:0: RAID COMPAQ MSA1000 5.20 PQ: 0 ANSI: 4 scsi 6:0:0:0: Attached scsi generic sg2 type 12 scsi 6:0:0:1: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:1: Attached scsi generic sg3 type 0 scsi 6:0:0:2: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:2: Attached scsi generic sg4 type 0 scsi 6:0:0:3: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:3: Attached scsi generic sg5 type 0 sd 6:0:0:1: [sdc] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:1: [sdc] Write Protect is off sd 6:0:0:1: [sdc] Mode Sense: 83 00 00 08 scsi 6:0:0:4: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:2: [sdd] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:4: Attached scsi generic sg6 type 0 scsi 6:0:0:5: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:5: Attached scsi generic sg7 type 0 sd 6:0:0:2: [sdd] Write Protect is off sd 6:0:0:2: [sdd] Mode Sense: 83 00 00 08 sd 6:0:0:1: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA scsi 6:0:0:6: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:3: [sde] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:6: Attached scsi generic sg8 type 0 scsi 6:0:0:7: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:4: [sdf] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:7: Attached scsi generic sg9 type 0 sd 6:0:0:5: [sdg] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:3: [sde] Write Protect is off sd 6:0:0:3: [sde] Mode Sense: 83 00 00 08 sd 6:0:0:2: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA scsi 6:0:0:8: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 sd 6:0:0:8: Attached scsi generic sg10 type 0 sd 6:0:0:6: [sdh] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:4: [sdf] Write Protect is off sd 6:0:0:4: [sdf] Mode Sense: 83 00 00 08 sd 6:0:0:5: [sdg] Write Protect is off sd 6:0:0:5: [sdg] Mode Sense: 83 00 00 08 scsi 6:0:1:0: Enclosure HP MSA2012fc J200 PQ: 0 ANSI: 5 scsi 6:0:1:0: Attached scsi generic sg11 type 13 sd 6:0:0:6: [sdh] Write Protect is off sd 6:0:0:6: [sdh] Mode Sense: 83 00 00 08 sd 6:0:0:3: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:7: [sdi] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) scsi 6:0:1:1: Direct-Access HP MSA2012fc J200 PQ: 0 ANSI: 5 sd 6:0:1:1: Attached scsi generic sg12 type 0 sd 6:0:0:8: [sdj] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:4: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: scsi 6:0:1:3: Direct-Access HP MSA2012fc J200 PQ: 0 ANSI: 5 sd 6:0:1:3: Attached scsi generic sg13 type 0 sd 6:0:1:1: [sdk] 7813967872 512-byte logical blocks: (4.00 TB/3.63 TiB) sd 6:0:0:7: [sdi] Write Protect is off sd 6:0:0:7: [sdi] Mode Sense: 83 00 00 08 sd 6:0:0:5: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:1:3: [sdl] 3906983936 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:0:8: [sdj] Write Protect is off sd 6:0:0:8: [sdj] Mode Sense: 83 00 00 08 sd 6:0:0:6: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA scsi 6:0:1:5: Direct-Access HP MSA2012fc J200 PQ: 0 ANSI: 5 sd 6:0:1:5: Attached scsi generic sg14 type 0 sd 6:0:1:1: [sdk] Write Protect is off sd 6:0:1:1: [sdk] Mode Sense: 93 00 00 08 sdd: sd 6:0:1:3: [sdl] Write Protect is off sd 6:0:1:3: [sdl] Mode Sense: 93 00 00 08 sd 6:0:1:5: [sdm] 3906984448 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:1:1: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:7: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA scsi 6:0:2:0: Direct-Access HP MSA2012fc J200 PQ: 0 ANSI: 5 sd 6:0:2:0: Attached scsi generic sg15 type 0 sd 6:0:1:3: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:8: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sd 6:0:1:5: [sdm] Write Protect is off sd 6:0:1:5: [sdm] Mode Sense: 93 00 00 08 sd 6:0:2:0: [sdn] 7813968896 512-byte logical blocks: (4.00 TB/3.63 TiB) scsi 6:0:2:2: Direct-Access HP MSA2012fc J200 PQ: 0 ANSI: 5 sd 6:0:2:2: Attached scsi generic sg16 type 0 sdf: sd 6:0:1:5: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdg: sdh: sd 6:0:2:0: [sdn] Write Protect is off sd 6:0:2:0: [sdn] Mode Sense: 93 00 00 08 sd 6:0:2:2: [sdo] 3906984448 512-byte logical blocks: (2.00 TB/1.81 TiB) scsi 6:0:2:4: Direct-Access HP MSA2012fc J200 PQ: 0 ANSI: 5 sdk: sd 6:0:2:4: Attached scsi generic sg17 type 0 sdi: sdj: sd 6:0:2:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdi1 sdl: sd 6:0:2:4: [sdp] 3906984448 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 6:0:2:2: [sdo] Write Protect is off sd 6:0:2:2: [sdo] Mode Sense: 93 00 00 08 sd 6:0:0:7: [sdi] Attached SCSI disk sd 6:0:2:2: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdm: sd 6:0:2:4: [sdp] Write Protect is off sd 6:0:2:4: [sdp] Mode Sense: 93 00 00 08 sd 6:0:2:4: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdn: sdo: sdp: sdp1 sd 6:0:2:4: [sdp] Attached SCSI disk sdh1 sd 6:0:0:6: [sdh] Attached SCSI disk sdl1 sdj1 sd 6:0:1:3: [sdl] Attached SCSI disk sdg1 sdo1 sdf1 sd 6:0:2:2: [sdo] Attached SCSI disk sd 6:0:0:5: [sdg] Attached SCSI disk sdc1 sd 6:0:0:8: [sdj] Attached SCSI disk sde1 sd 6:0:0:4: [sdf] Attached SCSI disk sd 6:0:0:1: [sdc] Attached SCSI disk sdd1 sd 6:0:0:3: [sde] Attached SCSI disk sdm1 sd 6:0:1:5: [sdm] Attached SCSI disk sd 6:0:0:2: [sdd] Attached SCSI disk sdn1 sd 6:0:2:0: [sdn] Attached SCSI disk sdk1 sd 6:0:1:1: [sdk] Attached SCSI disk EXT3 FS on md3, internal journal QLogic Fibre Channel HBA Driver: 8.03.01-k6 vboxdrv: Trying to deactivate the NMI watchdog permanently... vboxdrv: Successfully done. vboxdrv: Found 4 processor cores. VBoxDrv: dbg - g_abExecMemory=ffffffffa00e1680 vboxdrv: fAsync=0 offMin=0x56a offMax=0x29ee vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. vboxdrv: Successfully loaded version 3.0.12 (interface 0x00110000). VBoxNetFlt: dbg - g_abExecMemory=ffffffffa0284020 VBoxNetAdp: dbg - g_abExecMemory=ffffffffa02a2820 kjournald starting. Commit interval 5 seconds EXT3 FS on md5, internal journal EXT3-fs: mounted filesystem with writeback data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on md6, internal journal EXT3-fs: mounted filesystem with writeback data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on md7, internal journal EXT3-fs: mounted filesystem with writeback data mode. XFS mounting filesystem dm-4 Ending clean XFS mount for filesystem: dm-4 XFS mounting filesystem dm-0 Ending clean XFS mount for filesystem: dm-0 XFS mounting filesystem dm-1 Ending clean XFS mount for filesystem: dm-1 Adding 2008116k swap on /dev/sda2. Priority:1 extents:1 across:2008116k Adding 2008116k swap on /dev/sdb2. Priority:1 extents:1 across:2008116k ata1.00: configured for UDMA/100 ata1: EH complete ata2.00: configured for UDMA/100 ata2: EH complete tg3: eth0: Link is up at 1000 Mbps, full duplex. tg3: eth0: Flow control is off for TX and off for RX. warning: `VBoxHeadless' uses 32-bit capabilities (legacy support in use) device vlan10 entered promiscuous mode device eth0 entered promiscuous mode rport-6:0-9: blocked FC remote port time out: removing rport