dmesg from 2.6.32.2

2.6.32.2 (text/plain), 35.39 KB, created by Oleg Gawriloff on 2009-12-30 16:04:16 UTC

Linux version 2.6.32.2 (root@albatros2) (gcc version 4.3.4 (Gentoo 4.3.4 p1.0, pie-10.1.5) ) #1 SMP Fri Dec 25 19:53:51 EET 2009
Command line: 
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 0000000000099c00 (usable)
 BIOS-e820: 0000000000099c00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000bff10000 (usable)
 BIOS-e820: 00000000bff10000 - 00000000bff21000 (ACPI data)
 BIOS-e820: 00000000bff21000 - 00000000bff80000 (ACPI NVS)
 BIOS-e820: 00000000bff80000 - 00000000c0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
DMI present.
last_pfn = 0xbff10 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-CFFFF write-protect
  D0000-DFFFF uncachable
  E0000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 000000000 mask F80000000 write-back
  1 base 080000000 mask FC0000000 write-back
  2 base 0BFF80000 mask FFFF80000 uncachable
  3 disabled
  4 disabled
  5 disabled
  6 disabled
  7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bff10000
 0000000000 - 00bfe00000 page 2M
 00bfe00000 - 00bff10000 page 4k
kernel direct mapping tables up to bff10000 @ 8000-d000
(6 early reservations) ==> bootmem [0000000000 - 00bff10000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
  #2 [0001000000 - 0001809624]    TEXT DATA BSS ==> [0001000000 - 0001809624]
  #3 [0000099c00 - 0000100000]    BIOS reserved ==> [0000099c00 - 0000100000]
  #4 [000180a000 - 000180a1f8]              BRK ==> [000180a000 - 000180a1f8]
  #5 [0000008000 - 000000b000]          PGTABLE ==> [0000008000 - 000000b000]
found SMP MP-table at [ffff8800000f6f90] f6f90
 [ffffea0000000000-ffffea00029fffff] PMD -> [ffff880001e00000-ffff8800047fffff] on node 0
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x00000099
    0: 0x00000100 -> 0x000bff10
On node 0 totalpages: 786089
  DMA zone: 56 pages used for memmap
  DMA zone: 108 pages reserved
  DMA zone: 3829 pages, LIFO batch:0
  DMA32 zone: 10693 pages used for memmap
  DMA32 zone: 771403 pages, LIFO batch:31
Intel MultiProcessor Specification v1.4
MPTABLE: OEM ID: INTEL   
MPTABLE: Product ID: Bridge CRB  
MPTABLE: APIC at: 0xFEE00000
Processor #0 (Bootup-CPU)
Processor #6
Processor #1
Processor #7
I/O APIC #2 Version 32 at 0xFEC00000.
I/O APIC #3 Version 32 at 0xFEC80000.
Processors: 4
SMP: Allowing 4 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 48
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 24 pages/cpu @ffff880001a00000 s68632 r8192 d21480 u524288
pcpu-alloc: s68632 r8192 d21480 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 775232
Kernel command line: 
PID hash table entries: 4096 (order: 3, 32768 bytes)
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Memory: 3085760k/3144768k available (4716k kernel code, 412k absent, 57964k reserved, 2275k data, 372k init)
Hierarchical RCU implementation.
NR_IRQS:1280
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 1595.911 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 3191.82 BogoMIPS (lpj=15959110)
Security Framework initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Setting APIC routing to flat
ExtINT not setup in hardware but reported by MP table
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
CPU0: Intel(R) Xeon(R) CPU            5110  @ 1.60GHz stepping 06
Booting processor 1 APIC 0x6 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3191.96 BogoMIPS (lpj=15959803)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Xeon(R) CPU            5110  @ 1.60GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Booting processor 2 APIC 0x1 ip 0x6000
Initializing CPU#2
Calibrating delay using timer specific routine.. 3191.95 BogoMIPS (lpj=15959769)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU2: Thermal monitoring enabled (TM2)
CPU2: Intel(R) Xeon(R) CPU            5110  @ 1.60GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
Booting processor 3 APIC 0x7 ip 0x6000
Initializing CPU#3
Calibrating delay using timer specific routine.. 3191.93 BogoMIPS (lpj=15959668)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU3: Thermal monitoring enabled (TM2)
CPU3: Intel(R) Xeon(R) CPU            5110  @ 1.60GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
Total of 4 processors activated (12767.67 BogoMIPS).
NET: Registered protocol family 16
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
pci 0000:00:1d.2: reg 20 io port: [0x1840-0x185f]
pci 0000:00:1d.3: reg 20 io port: [0x1860-0x187f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xdff00000-0xdff003ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x1880-0x188f]
pci 0000:00:1f.2: reg 10 io port: [0x18c0-0x18c7]
pci 0000:00:1f.2: reg 14 io port: [0x1894-0x1897]
pci 0000:00:1f.2: reg 18 io port: [0x1898-0x189f]
pci 0000:00:1f.2: reg 1c io port: [0x1890-0x1893]
pci 0000:00:1f.2: reg 20 io port: [0x18a0-0x18bf]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xdff00400-0xdff007ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20 io port: [0x18e0-0x18ff]
pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.3: PME# supported from D0 D3hot D3cold
pci 0000:01:00.3: PME# disabled
pci 0000:00:02.0: bridge 32bit mmio: [0xdf900000-0xdf9fffff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:10:00.0: reg 10 64bit mmio: [0xdfb01000-0xdfb01fff]
pci 0000:10:00.0: reg 18 64bit mmio: [0xdfb00000-0xdfb000ff]
pci 0000:10:00.0: reg 20 io port: [0x2000-0x20ff]
pci 0000:10:00.0: reg 30 32bit mmio pref: [0x000000-0x03ffff]
pci 0000:00:04.0: bridge io port: [0x2000-0x2fff]
pci 0000:00:04.0: bridge 32bit mmio: [0xdfb00000-0xdfbfffff]
pci 0000:1e:00.0: reg 10 64bit mmio: [0xdfa00000-0xdfa0ffff]
pci 0000:1e:00.0: PME# supported from D3hot D3cold
pci 0000:1e:00.0: PME# disabled
pci 0000:00:1c.0: bridge 32bit mmio: [0xdfa00000-0xdfafffff]
pci 0000:1f:00.0: reg 10 64bit mmio: [0xdfc00000-0xdfc0ffff]
pci 0000:1f:00.0: PME# supported from D3hot D3cold
pci 0000:1f:00.0: PME# disabled
pci 0000:00:1c.1: bridge 32bit mmio: [0xdfc00000-0xdfcfffff]
pci 0000:20:02.0: reg 10 32bit mmio pref: [0xde000000-0xdeffffff]
pci 0000:20:02.0: reg 14 32bit mmio: [0xdf800000-0xdf803fff]
pci 0000:20:02.0: reg 18 32bit mmio: [0xdf000000-0xdf7fffff]
pci 0000:20:02.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xdf000000-0xdf8fffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xde000000-0xdeffffff]
vgaarb: device added: PCI:0000:20:02.0,decodes=io+mem,owns=io+mem,locks=none
PCI: Discovered primary peer bus 05 [IRQ]
pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:2670]
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Switching to clocksource tsc
pci 0000:02:00.0: PCI bridge, secondary bus 0000:03
pci 0000:02:00.0:   IO window: disabled
pci 0000:02:00.0:   MEM window: disabled
pci 0000:02:00.0:   PREFETCH window: disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: disabled
pci 0000:01:00.0:   PREFETCH window: disabled
pci 0000:01:00.3: PCI bridge, secondary bus 0000:0b
pci 0000:01:00.3:   IO window: disabled
pci 0000:01:00.3:   MEM window: disabled
pci 0000:01:00.3:   PREFETCH window: disabled
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0:   IO window: disabled
pci 0000:00:02.0:   MEM window: 0xdf900000-0xdf9fffff
pci 0000:00:02.0:   PREFETCH window: disabled
pci 0000:00:03.0: PCI bridge, secondary bus 0000:0c
pci 0000:00:03.0:   IO window: disabled
pci 0000:00:03.0:   MEM window: disabled
pci 0000:00:03.0:   PREFETCH window: disabled
pci 0000:00:04.0: PCI bridge, secondary bus 0000:10
pci 0000:00:04.0:   IO window: 0x2000-0x2fff
pci 0000:00:04.0:   MEM window: 0xdfb00000-0xdfbfffff
pci 0000:00:04.0:   PREFETCH window: 0xc0000000-0xc00fffff
pci 0000:00:05.0: PCI bridge, secondary bus 0000:11
pci 0000:00:05.0:   IO window: disabled
pci 0000:00:05.0:   MEM window: disabled
pci 0000:00:05.0:   PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:12
pci 0000:00:06.0:   IO window: disabled
pci 0000:00:06.0:   MEM window: disabled
pci 0000:00:06.0:   PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:13
pci 0000:00:07.0:   IO window: disabled
pci 0000:00:07.0:   MEM window: disabled
pci 0000:00:07.0:   PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:1e
pci 0000:00:1c.0:   IO window: 0x3000-0x3fff
pci 0000:00:1c.0:   MEM window: 0xdfa00000-0xdfafffff
pci 0000:00:1c.0:   PREFETCH window: 0x000000c0100000-0x000000c02fffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:1f
pci 0000:00:1c.1:   IO window: 0x4000-0x4fff
pci 0000:00:1c.1:   MEM window: 0xdfc00000-0xdfcfffff
pci 0000:00:1c.1:   PREFETCH window: 0x000000c0300000-0x000000c04fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:20
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: 0xdf000000-0xdf8fffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000de000000-0x000000deffffff
pci 0000:00:02.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:00:02.0: setting latency timer to 64
pci 0000:01:00.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:01:00.0: setting latency timer to 64
pci 0000:02:00.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:02:00.0: setting latency timer to 64
pci 0000:01:00.3: setting latency timer to 64
pci 0000:00:03.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:04.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: can't find IRQ for PCI INT A; probably buggy MP table
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 1 mem: [0xdf900000-0xdf9fffff]
pci_bus 0000:10: resource 0 io:  [0x2000-0x2fff]
pci_bus 0000:10: resource 1 mem: [0xdfb00000-0xdfbfffff]
pci_bus 0000:10: resource 2 pref mem [0xc0000000-0xc00fffff]
pci_bus 0000:1e: resource 0 io:  [0x3000-0x3fff]
pci_bus 0000:1e: resource 1 mem: [0xdfa00000-0xdfafffff]
pci_bus 0000:1e: resource 2 pref mem [0xc0100000-0xc02fffff]
pci_bus 0000:1f: resource 0 io:  [0x4000-0x4fff]
pci_bus 0000:1f: resource 1 mem: [0xdfc00000-0xdfcfffff]
pci_bus 0000:1f: resource 2 pref mem [0xc0300000-0xc04fffff]
pci_bus 0000:20: resource 1 mem: [0xdf000000-0xdf8fffff]
pci_bus 0000:20: resource 2 pref mem [0xde000000-0xdeffffff]
pci_bus 0000:20: resource 3 io:  [0x00-0xffff]
pci_bus 0000:20: resource 4 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:05: resource 0 io:  [0x00-0xffff]
pci_bus 0000:05: resource 1 mem: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
pci 0000:20:02.0: Boot video device
platform rtc_cmos: registered platform RTC device (no PNP device found)
audit: initializing netlink socket (disabled)
type=2000 audit(1262178448.790:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [e-mail]).
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.13)
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
msgmni has been set to 6028
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
pcieport 0000:00:02.0: device [8086:25f7] has invalid IRQ; check vendor BIOS
pcieport 0000:00:02.0: irq 48 for MSI/MSI-X
pcieport 0000:00:02.0: setting latency timer to 64
pcieport 0000:00:03.0: device [8086:25e3] has invalid IRQ; check vendor BIOS
pcieport 0000:00:03.0: irq 49 for MSI/MSI-X
pcieport 0000:00:03.0: setting latency timer to 64
pcieport 0000:00:04.0: device [8086:25fa] has invalid IRQ; check vendor BIOS
pcieport 0000:00:04.0: irq 50 for MSI/MSI-X
pcieport 0000:00:04.0: setting latency timer to 64
pcieport 0000:00:05.0: device [8086:25e5] has invalid IRQ; check vendor BIOS
pcieport 0000:00:05.0: irq 51 for MSI/MSI-X
pcieport 0000:00:05.0: setting latency timer to 64
pcieport 0000:00:06.0: device [8086:25e6] has invalid IRQ; check vendor BIOS
pcieport 0000:00:06.0: irq 52 for MSI/MSI-X
pcieport 0000:00:06.0: setting latency timer to 64
pcieport 0000:00:07.0: device [8086:25e7] has invalid IRQ; check vendor BIOS
pcieport 0000:00:07.0: irq 53 for MSI/MSI-X
pcieport 0000:00:07.0: setting latency timer to 64
pcieport 0000:00:1c.0: irq 54 for MSI/MSI-X
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.1: irq 55 for MSI/MSI-X
pcieport 0000:00:1c.1: setting latency timer to 64
pcieport 0000:01:00.0: setting latency timer to 64
pcieport 0000:02:00.0: irq 56 for MSI/MSI-X
pcieport 0000:02:00.0: setting latency timer to 64
Real Time Clock Driver v1.12b
intel_rng: FWH not detected
Linux agpgart interface v0.103
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
nbd: registered device at major 43
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x269e rev 0x09)
PIIX_IDE 0000:00:1f.1: PCI->APIC IRQ transform: INT A -> IRQ 19
piix 0000:00:1f.1: IDE port disabled
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1880-0x1887
Probing IDE interface ide0...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-gd driver 1.18
ide-cd driver 5.00
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI->APIC IRQ transform: INT B -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit pm led pmp slum part 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 irq_stat 0x00000040, connection status changed
ata2: SATA max UDMA/133 irq_stat 0x00000040, connection status changed
ata3: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00600 irq 19
ata4: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00680 irq 19
ata5: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00700 irq 19
ata6: SATA max UDMA/133 abar m1024@0xdff00400 port 0xdff00780 irq 19
Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
Copyright (c) 1999-2006 Intel Corporation.
tg3.c:v3.102 (September 1, 2009)
tg3 0000:1e:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16
tg3 0000:1e:00.0: setting latency timer to 64
eth0: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:1a:4b:a4:08:ce
eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
tg3 0000:1f:00.0: PCI->APIC IRQ transform: INT A -> IRQ 17
tg3 0000:1f:00.0: setting latency timer to 64
eth1: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:1a:4b:a4:08:cf
eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
console [netcon0] enabled
netconsole: network logging started
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: Enabling legacy PCI PM
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff00000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI->APIC IRQ transform: INT B -> IRQ 23
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 23, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI->APIC IRQ transform: INT C -> IRQ 23
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 23, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI->APIC IRQ transform: INT D -> IRQ 23
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001860
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042.c: Warning: Keylock active.
Failed to disable AUX port, but continuing anyway... Is this a SiS?
If AUX port is really absent please use the 'i8042.noaux' option.
ata4: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: SATA link down (SStatus 0 SControl 300)
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
coretemp coretemp.2: Using relative temperature scale!
coretemp coretemp.3: Using relative temperature scale!
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [e-mail]
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <[e-mail]>
All bugs added by David S. Miller <[e-mail]>
registered taskstats version 1
usb 4-1: new full speed USB device using uhci_hcd and address 2
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FB080C4080,     HPF0, max UDMA/100
ata1.00: 156301488 sectors, multi 0: LBA48 
ata2.00: ATA-7: FB080C4080,     HPF0, max UDMA/100
ata2.00: 156301488 sectors, multi 0: LBA48 
ata2.00: configured for UDMA/100
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      FB080C4080       n/a  PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access     ATA      FB080C4080       n/a  PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:
sd 1:0:0:0: [sdb] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sda1 sda2 sda3 sda4 < sdb1 sdb2 sdb3 sdb4 < sda5 sdb5 sdb6 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
 sdb7 >
sd 1:0:0:0: [sdb] Attached SCSI disk
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
usb 4-1: configuration #1 chosen from 1 choice
input: ServerEngines SE USB Device as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input0
generic-usb 0003:0000:0000.0001: input: USB HID v1.11 Keyboard [ServerEngines SE USB Device] on usb-0000:00:1d.2-1/input0
input: ServerEngines SE USB Device as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input1
generic-usb 0003:0000:0000.0002: input: USB HID v1.11 Mouse [ServerEngines SE USB Device] on usb-0000:00:1d.2-1/input1
md: Scanned 10 and added 10 devices.
md: autorun ...
md: considering sdb7 ...
md:  adding sdb7 ...
md: sdb6 has different UUID to sdb7
md: sdb5 has different UUID to sdb7
md: sdb3 has different UUID to sdb7
md: sdb1 has different UUID to sdb7
md:  adding sda7 ...
md: sda6 has different UUID to sdb7
md: sda5 has different UUID to sdb7
md: sda3 has different UUID to sdb7
md: sda1 has different UUID to sdb7
md: created md7
md: bind<sda7>
md: bind<sdb7>
md: running: <sdb7><sda7>
raid1: raid set md7 active with 2 out of 2 mirrors
md7: detected capacity change from 0 to 45131956224
md: considering sdb6 ...
md:  adding sdb6 ...
md: sdb5 has different UUID to sdb6
md: sdb3 has different UUID to sdb6
md: sdb1 has different UUID to sdb6
md:  adding sda6 ...
md: sda5 has different UUID to sdb6
md: sda3 has different UUID to sdb6
md: sda1 has different UUID to sdb6
md: created md6
md: bind<sda6>
md: bind<sdb6>
md: running: <sdb6><sda6>
raid1: raid set md6 active with 2 out of 2 mirrors
md6: detected capacity change from 0 to 2056192000
md: considering sdb5 ...
md:  adding sdb5 ...
md: sdb3 has different UUID to sdb5
md: sdb1 has different UUID to sdb5
md:  adding sda5 ...
md: sda3 has different UUID to sdb5
md: sda1 has different UUID to sdb5
md: created md5
md: bind<sda5>
md: bind<sdb5>
md: running: <sdb5><sda5>
raid1: raid set md5 active with 2 out of 2 mirrors
md5: detected capacity change from 0 to 20489043968
md: considering sdb3 ...
md:  adding sdb3 ...
md: sdb1 has different UUID to sdb3
md:  adding sda3 ...
md: sda1 has different UUID to sdb3
md: created md3
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3>
raid1: raid set md3 active with 2 out of 2 mirrors
md3: detected capacity change from 0 to 10248585216
md: considering sdb1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md1
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md1 active with 2 out of 2 mirrors
md1: detected capacity change from 0 to 41025536
md: ... autorun DONE.
 md3: unknown partition table
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 9:3.
Freeing unused kernel memory: 372k freed
Write protecting the kernel read-only data: 6296k
udev: starting version 146
Emulex LightPulse Fibre Channel SCSI driver 8.3.4
Copyright(c) 2004-2009 Emulex.  All rights reserved.
lpfc 0000:10:00.0: PCI->APIC IRQ transform: INT A -> IRQ 16
lpfc 0000:10:00.0: setting latency timer to 64
scsi6 :  on PCI bus 10 device 00 irq 16
 md1:
 md6:
 md7:
 md5: unknown partition table
 unknown partition table
 unknown partition table
 unknown partition table
lpfc 0000:10:00.0: 0:1303 Link Up Event x1 received Data: x1 xf7 x10 x0 x0 x0 0
scsi 6:0:0:0: RAID              COMPAQ   MSA1000          5.20 PQ: 0 ANSI: 4
scsi 6:0:0:0: Attached scsi generic sg2 type 12
scsi 6:0:0:1: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:1: Attached scsi generic sg3 type 0
scsi 6:0:0:2: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:2: Attached scsi generic sg4 type 0
sd 6:0:0:1: [sdc] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
scsi 6:0:0:3: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:3: Attached scsi generic sg5 type 0
sd 6:0:0:1: [sdc] Write Protect is off
sd 6:0:0:1: [sdc] Mode Sense: 83 00 00 08
sd 6:0:0:2: [sdd] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
scsi 6:0:0:4: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:4: Attached scsi generic sg6 type 0
sd 6:0:0:2: [sdd] Write Protect is off
sd 6:0:0:2: [sdd] Mode Sense: 83 00 00 08
sd 6:0:0:3: [sde] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
scsi 6:0:0:5: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:5: Attached scsi generic sg7 type 0
sd 6:0:0:1: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:3: [sde] Write Protect is off
sd 6:0:0:3: [sde] Mode Sense: 83 00 00 08
scsi 6:0:0:6: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:4: [sdf] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 6:0:0:6: Attached scsi generic sg8 type 0
sd 6:0:0:2: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
scsi 6:0:0:7: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:7: Attached scsi generic sg9 type 0
sd 6:0:0:5: [sdg] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 6:0:0:4: [sdf] Write Protect is off
sd 6:0:0:4: [sdf] Mode Sense: 83 00 00 08
scsi 6:0:0:8: Direct-Access     COMPAQ   MSA1000 VOLUME   5.20 PQ: 0 ANSI: 4
sd 6:0:0:3: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:8: Attached scsi generic sg10 type 0
sd 6:0:0:6: [sdh] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 6:0:0:5: [sdg] Write Protect is off
sd 6:0:0:5: [sdg] Mode Sense: 83 00 00 08
sd 6:0:0:7: [sdi] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
scsi 6:0:1:0: Enclosure         HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:0:6: [sdh] Write Protect is off
sd 6:0:0:6: [sdh] Mode Sense: 83 00 00 08
scsi 6:0:1:0: Attached scsi generic sg11 type 13
sd 6:0:0:8: [sdj] 3906911610 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 6:0:0:4: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:0:7: [sdi] Write Protect is off
sd 6:0:0:7: [sdi] Mode Sense: 83 00 00 08
 sdc:
sd 6:0:0:5: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
scsi 6:0:1:1: Direct-Access     HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:0:8: [sdj] Write Protect is off
sd 6:0:0:8: [sdj] Mode Sense: 83 00 00 08
sd 6:0:1:1: Attached scsi generic sg12 type 0
sd 6:0:0:6: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdd:
scsi 6:0:1:3: Direct-Access     HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:1:1: [sdk] 7813967872 512-byte logical blocks: (4.00 TB/3.63 TiB)
sd 6:0:0:7: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:1:3: Attached scsi generic sg13 type 0
 sdc1
sd 6:0:1:3: [sdl] 3906983936 512-byte logical blocks: (2.00 TB/1.81 TiB)
 sde:
scsi 6:0:1:5: Direct-Access     HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:1:1: [sdk] Write Protect is off
sd 6:0:1:1: [sdk] Mode Sense: 93 00 00 08
sd 6:0:0:8: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:1:5: Attached scsi generic sg14 type 0
sd 6:0:1:1: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:1:3: [sdl] Write Protect is off
sd 6:0:1:3: [sdl] Mode Sense: 93 00 00 08
scsi 6:0:2:0: Direct-Access     HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:2:0: Attached scsi generic sg15 type 0
 sdf:
sd 6:0:1:3: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:1:5: [sdm] 3906984448 512-byte logical blocks: (2.00 TB/1.81 TiB)
 sdg:
sd 6:0:2:0: [sdn] 7813968896 512-byte logical blocks: (4.00 TB/3.63 TiB)
 sdh:
 sdi:
sd 6:0:0:1: [sdc] Attached SCSI disk
scsi 6:0:2:2: Direct-Access     HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:2:2: Attached scsi generic sg16 type 0
sd 6:0:1:5: [sdm] Write Protect is off
sd 6:0:1:5: [sdm] Mode Sense: 93 00 00 08
 sdj: sdj1
sd 6:0:2:0: [sdn] Write Protect is off
sd 6:0:2:0: [sdn] Mode Sense: 93 00 00 08
scsi 6:0:2:4: Direct-Access     HP       MSA2012fc        J200 PQ: 0 ANSI: 5
sd 6:0:1:5: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:2:2: [sdo] 3906984448 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 6:0:2:4: Attached scsi generic sg17 type 0
 sdk:
sd 6:0:2:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdl:
sd 6:0:2:2: [sdo] Write Protect is off
sd 6:0:2:2: [sdo] Mode Sense: 93 00 00 08
sd 6:0:2:4: [sdp] 3906984448 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 6:0:0:8: [sdj] Attached SCSI disk
sd 6:0:2:2: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 6:0:2:4: [sdp] Write Protect is off
sd 6:0:2:4: [sdp] Mode Sense: 93 00 00 08
 sdm:
sd 6:0:2:4: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdn:
 sdo:
 sdp: sde1
 sdl1
 sdi1
sd 6:0:1:3: [sdl] Attached SCSI disk
 sdf1
 sdg1
 sdd1
 sdo1
sd 6:0:0:7: [sdi] Attached SCSI disk
sd 6:0:0:3: [sde] Attached SCSI disk
sd 6:0:2:2: [sdo] Attached SCSI disk
 sdh1
sd 6:0:0:2: [sdd] Attached SCSI disk
sd 6:0:0:4: [sdf] Attached SCSI disk
sd 6:0:0:5: [sdg] Attached SCSI disk
 sdp1
sd 6:0:0:6: [sdh] Attached SCSI disk
sd 6:0:2:4: [sdp] Attached SCSI disk
 sdm1
sd 6:0:1:5: [sdm] Attached SCSI disk
EXT3 FS on md3, internal journal
 sdn1
sd 6:0:2:0: [sdn] Attached SCSI disk
 sdk1
sd 6:0:1:1: [sdk] Attached SCSI disk
QLogic Fibre Channel HBA Driver: 8.03.01-k6
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 4 processor cores.
VBoxDrv: dbg - g_abExecMemory=ffffffffa00e16a0
vboxdrv: fAsync=0 offMin=0x576 offMax=0x1a94
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 3.0.12 (interface 0x00110000).
VBoxNetFlt: dbg - g_abExecMemory=ffffffffa0284040
VBoxNetAdp: dbg - g_abExecMemory=ffffffffa02a2840
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md6, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md7, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
XFS mounting filesystem dm-4
Ending clean XFS mount for filesystem: dm-4
XFS mounting filesystem dm-0
Ending clean XFS mount for filesystem: dm-0
XFS mounting filesystem dm-1
Ending clean XFS mount for filesystem: dm-1
Adding 2008116k swap on /dev/sda2.  Priority:1 extents:1 across:2008116k 
Adding 2008116k swap on /dev/sdb2.  Priority:1 extents:1 across:2008116k