dmesg output (after shorewall/iptables start)

ooops.dmesg.thinkpad_sl500.090108.txt (text/plain), 30.30 KB, created by Jochen Schlick on 2009-01-08 19:38:02 UTC

 0000:00:1f.2: reg 1c io port: [0x4800-0x4803]
pci 0000:00:1f.2: reg 20 io port: [0x4480-0x449f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xf9eff000-0xf9eff7ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff]
pci 0000:01:00.0: reg 24 io port: [0x6c00-0x6c7f]
pci 0000:01:00.0: reg 30 32bit mmio: [0xf9fe0000-0xf9ffffff]
pci 0000:00:01.0: bridge io port: [0x6000-0x6fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xf9f00000-0xfcffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:03:00.0: reg 10 64bit mmio: [0xfd6fe000-0xfd6fffff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge 32bit mmio: [0xfd600000-0xfd6fffff]
pci 0000:00:1c.2: bridge io port: [0x7000-0xdfff]
pci 0000:00:1c.2: bridge 32bit mmio: [0xfd700000-0xfddfffff]
pci 0000:00:1c.2: bridge 64bit mmio pref: [0xf8800000-0xf8efffff]
pci 0000:0c:00.0: reg 10 io port: [0xe800-0xe8ff]
pci 0000:0c:00.0: reg 18 64bit mmio: [0xf8fff000-0xf8ffffff]
pci 0000:0c:00.0: reg 20 64bit mmio: [0xf8fe0000-0xf8feffff]
pci 0000:0c:00.0: reg 30 32bit mmio: [0xfdef0000-0xfdefffff]
pci 0000:0c:00.0: supports D1 D2
pci 0000:0c:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0c:00.0: PME# disabled
pci 0000:00:1c.3: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.3: bridge 32bit mmio: [0xfde00000-0xfdefffff]
pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf8f00000-0xf8ffffff]
pci 0000:0d:00.0: reg 10 32bit mmio: [0xfdfff800-0xfdffffff]
pci 0000:0d:00.0: PME# supported from D0 D3hot D3cold
pci 0000:0d:00.0: PME# disabled
pci 0000:0d:00.1: reg 10 32bit mmio: [0xfdfff400-0xfdfff4ff]
pci 0000:0d:00.1: supports D1 D2
pci 0000:0d:00.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0d:00.1: PME# disabled
pci 0000:0d:00.2: reg 10 32bit mmio: [0xfdfff000-0xfdfff0ff]
pci 0000:0d:00.2: supports D1 D2
pci 0000:0d:00.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0d:00.2: PME# disabled
pci 0000:0d:00.3: reg 10 32bit mmio: [0xfdffec00-0xfdffecff]
pci 0000:0d:00.3: supports D1 D2
pci 0000:0d:00.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:0d:00.3: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfdf00000-0xfdffffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 10 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *6)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 10 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 6) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 10 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 7 10 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 12)
ACPI Warning (tbutils-0217): Incorrect checksum in table [ATKG] - C9, should be 84 [20080926]
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0c: mem resource (0xfdbfac00-0xfdc3abff) overlaps 0000:00:1c.2 BAR 8 (0xfd700000-0xfddfffff), disabling
pnp 00:0c: mem resource (0xfdefac00-0xfdf3abff) overlaps 0000:00:1c.3 BAR 8 (0xfde00000-0xfdefffff), disabling
pnp 00:0c: mem resource (0xfdefac00-0xfdf3abff) overlaps 0000:00:1e.0 BAR 8 (0xfdf00000-0xfdffffff), disabling
pnp 00:0c: mem resource (0xfdefac00-0xfdf3abff) overlaps 0000:0c:00.0 BAR 6 (0xfdef0000-0xfdefffff), disabling
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed10000-0xfed19fff has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
system 00:08: ioport range 0x800-0x87f has been reserved
system 00:08: ioport range 0x400-0x41f has been reserved
system 00:08: ioport range 0x480-0x4bf has been reserved
system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:08: iomem range 0xfed45000-0xfed89fff has been reserved
system 00:08: iomem range 0xfed90000-0xfed90fff has been reserved
system 00:08: iomem range 0xfed91000-0xfed91fff has been reserved
system 00:08: iomem range 0xfed92000-0xfed92fff has been reserved
system 00:08: iomem range 0xfed93000-0xfed93fff has been reserved
system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:08: iomem range 0xfff00000-0xffffffff has been reserved
system 00:0a: iomem range 0xffa00000-0xffbfffff could not be reserved
system 00:0a: iomem range 0xffe00000-0xffffffff could not be reserved
system 00:0b: iomem range 0xffc00000-0xffdfffff has been reserved
system 00:0c: ioport range 0x250-0x253 has been reserved
system 00:0c: ioport range 0x256-0x25f has been reserved
system 00:0c: ioport range 0x702-0x703 has been reserved
system 00:0c: ioport range 0x4c0-0x4cf has been reserved
system 00:0c: ioport range 0x4d2-0x4df has been reserved
system 00:0c: ioport range 0x4e0-0x4ef has been reserved
system 00:0c: ioport range 0x4f0-0x4ff has been reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0c: iomem range 0xf9efc000-0xf9efefff has been reserved
system 00:0c: iomem range 0xfe0fac00-0xfe13abff has been reserved
system 00:0c: iomem range 0xfe1fac00-0xfe23abff has been reserved
system 00:0c: iomem range 0xf7ffec00-0xf7ffec03 has been reserved
system 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0e: iomem range 0x0-0x9ffff could not be reserved
system 00:0e: iomem range 0xc0000-0xcffff has been reserved
system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
system 00:0e: iomem range 0x100000-0xbfffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: 0x6000-0x6fff
pci 0000:00:01.0:   MEM window: 0xf9f00000-0xfcffffff
pci 0000:00:01.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1:   IO window: disabled
pci 0000:00:1c.1:   MEM window: 0xfd600000-0xfd6fffff
pci 0000:00:1c.1:   PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.2:   IO window: 0x7000-0xdfff
pci 0000:00:1c.2:   MEM window: 0xfd700000-0xfddfffff
pci 0000:00:1c.2:   PREFETCH window: 0x000000f8800000-0x000000f8efffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:0c
pci 0000:00:1c.3:   IO window: 0xe000-0xefff
pci 0000:00:1c.3:   MEM window: 0xfde00000-0xfdefffff
pci 0000:00:1c.3:   PREFETCH window: 0x000000f8f00000-0x000000f8ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0d
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: 0xfdf00000-0xfdffffff
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64
pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
bus: 01 index 0 io port: [0x6000-0x6fff]
bus: 01 index 1 mmio: [0xf9f00000-0xfcffffff]
bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 mmio: [0x0-0x0]
bus: 02 index 1 mmio: [0x0-0x0]
bus: 02 index 2 mmio: [0x0-0x0]
bus: 02 index 3 mmio: [0x0-0x0]
bus: 03 index 0 mmio: [0x0-0x0]
bus: 03 index 1 mmio: [0xfd600000-0xfd6fffff]
bus: 03 index 2 mmio: [0x0-0x0]
bus: 03 index 3 mmio: [0x0-0x0]
bus: 04 index 0 io port: [0x7000-0xdfff]
bus: 04 index 1 mmio: [0xfd700000-0xfddfffff]
bus: 04 index 2 mmio: [0xf8800000-0xf8efffff]
bus: 04 index 3 mmio: [0x0-0x0]
bus: 0c index 0 io port: [0xe000-0xefff]
bus: 0c index 1 mmio: [0xfde00000-0xfdefffff]
bus: 0c index 2 mmio: [0xf8f00000-0xf8ffffff]
bus: 0c index 3 mmio: [0x0-0x0]
bus: 0d index 0 mmio: [0x0-0x0]
bus: 0d index 1 mmio: [0xfdf00000-0xfdffffff]
bus: 0d index 2 mmio: [0x0-0x0]
bus: 0d index 3 io port: [0x00-0xffff]
bus: 0d index 4 mmio: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Simple Boot Flag at 0x51 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1231445922.319:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 7934
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pcieport-driver 0000:00:01.0: irq 383 for MSI/MSI-X
pci_express 0000:00:01.0:pcie00: allocate port service
pci_express 0000:00:01.0:pcie02: allocate port service
pci_express 0000:00:01.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pcieport-driver 0000:00:1c.0: irq 382 for MSI/MSI-X
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: found MSI capability
pcieport-driver 0000:00:1c.1: irq 381 for MSI/MSI-X
pci_express 0000:00:1c.1:pcie00: allocate port service
pci_express 0000:00:1c.1:pcie03: allocate port service
pcieport-driver 0000:00:1c.2: setting latency timer to 64
pcieport-driver 0000:00:1c.2: found MSI capability
pcieport-driver 0000:00:1c.2: irq 380 for MSI/MSI-X
pci_express 0000:00:1c.2:pcie00: allocate port service
pci_express 0000:00:1c.2:pcie02: allocate port service
pci_express 0000:00:1c.2:pcie03: allocate port service
pcieport-driver 0000:00:1c.3: setting latency timer to 64
pcieport-driver 0000:00:1c.3: found MSI capability
pcieport-driver 0000:00:1c.3: irq 379 for MSI/MSI-X
pci_express 0000:00:1c.3:pcie00: allocate port service
pci_express 0000:00:1c.3:pcie03: allocate port service
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
uvesafb: failed to execute /sbin/v86d
uvesafb: make sure that the v86d helper is installed and executable
uvesafb: Getting VBE info block failed (eax=0x4f00, err=-2)
uvesafb: vbe_init() failed with -22
uvesafb: probe of uvesafb.0 failed with error -22
vesafb: framebuffer at 0xfb000000, mapped to 0xffffc20011100000, using 13781k, total 14336k
vesafb: mode is 1680x1050x32, linelength=6720, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 210x65
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
fb0: VESA VGA frame buffer device
ACPI Warning (tbutils-0217): Incorrect checksum in table [SSDT] - FA, should be 89 [20080926]
ACPI: SSDT BFFC67C0, 0286 (r1  PmRef TP-6A         180 INTL 20051117)
ACPI: SSDT BFFC6AE0, 0765 (r1  PmRef  Cpu0Cst     3001 INTL 20051117)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [P001] (supports 8 throttling states)
ACPI Warning (tbutils-0217): Incorrect checksum in table [SSDT] - 37, should be C7 [20080926]
ACPI: SSDT BFFC66F0, 00C8 (r1  PmRef TP-6A         180 INTL 20051117)
ACPI: SSDT BFFC6A50, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20051117)
ACPI: CPU1 (power states: C1[C1] C2[C3])
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [P002] (supports 8 throttling states)
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI Warning (nspredef-0858): \_TZ_.THRM._PSL: Return Package type mismatch at index 0 - found Processor, expected Reference [20080926]
ACPI: Expecting a [Reference] package element, found type C
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (47 C)
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
brd: module loaded
loop: module loaded
Fixed MDIO Bus: probed
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 378 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff100 irq 378
ata2: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff180 irq 378
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff300 irq 378
ata6: SATA max UDMA/133 abar m2048@0xf9eff000 port 0xf9eff380 irq 378
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: ATA-8: ST9250827AS, 3.CMF, max UDMA/100
ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
ata2.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata2.00: ATAPI: MATSHITADVD-RAM UJ870A, SB23, max UDMA/33
ata2.00: ACPI cmd ef/10:06:00:00:00:a0 succeeded
ata2.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata2.00: configured for UDMA/33
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST9250827AS      3.CM PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ870A   SB23 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [e-mail]
EDAC MC: Ver: 2.1.0 Jan  8 2009
cpuidle: using governor ladder
cpuidle: using governor menu
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Marking TSC unstable due to TSC halts in idle
rtc_cmos 00:03: setting system clock to 2009-01-08 20:18:44 UTC (1231445924)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Clocksource tsc unstable (delta = -93873377 ns)
Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1c0b1, caps: 0xd04791/0xb00000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input2
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 468k freed
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input5
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
	(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
input: PC Speaker as /class/input/input6
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ACPI: Lid Switch [LID]
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC0] (on-line)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:0c:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
r8169 0000:0c:00.0: setting latency timer to 64
r8169 0000:0c:00.0: irq 377 for MSI/MSI-X
eth0: RTL8168c/8111c at 0xffffc200110fe000, 00:22:15:eb:43:e9, XID 3c4000c0 IRQ 377
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00005c00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00005880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.2: irq 19, io base 0x00005800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00005480
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00005400
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005080
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
sdhci-pci 0000:0d:00.1: SDHCI controller found [1180:0822] (rev 22)
sdhci-pci 0000:0d:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
sdhci-pci 0000:0d:00.1: Will use DMA mode even though HW doesn't fully claim to support it.
Registered led device: mmc0
mmc0: SDHCI controller on PCI [0000:0d:00.1] using DMA
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
acpi device:23: registered as cooling_device2
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9effc00
input: Video Bus as /class/input/input7
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9eff800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 6 ports detected
ohci1394 0000:0d:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]  MMIO=[fdfff800-fdffffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
iwlagn: Copyright(c) 2003-2008 Intel Corporation
iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:03:00.0: setting latency timer to 64
iwlagn: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
iwlagn: Tunable channels: 13 802.11bg, 24 802.11a channels
iwlagn 0000:03:00.0: PCI INT A disabled
phy0: Selected rate control algorithm 'iwl-agn-rs'
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
usb 8-5: new high speed USB device using ehci_hcd and address 2
usb 8-5: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
nvidia: module license 'NVIDIA' taints kernel.
usb 3-1: configuration #1 chosen from 1 choice
nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  180.18  Thu Dec 18 14:31:41 PST 2008
usb 3-2: new full speed USB device using uhci_hcd and address 3
Linux video capture interface: v2.00
usb 3-2: configuration #1 chosen from 1 choice
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00061b000081b0e9]
Bluetooth: Core ver 2.13
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
uvcvideo: Found UVC 1.00 device CNF7237&CNF7238 (17ef:4808)
input: CNF7237&CNF7238 as /class/input/input8
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
Bluetooth: Generic Bluetooth USB driver ver 0.3
usbcore: registered new interface driver btusb
EXT3 FS on sda5, internal journal
XFS mounting filesystem sda7
Ending clean XFS mount for filesystem: sda7
fbcondecor: console 0 using theme 'livecd-2007.0'
fbcondecor: switched decor state to 'on' on console 0
fbcondecor: console 1 using theme 'livecd-2007.0'
fbcondecor: switched decor state to 'on' on console 1
Adding 4200956k swap on /dev/sda6.  Priority:-1 extents:1 across:4200956k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:03:00.0: restoring config space at offset 0x1 (was 0x100002, writing 0x100006)
iwlagn 0000:03:00.0: irq 376 for MSI/MSI-X
iwlagn 0000:03:00.0: firmware: requesting iwlwifi-5000-1.ucode
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
Bridge firewalling registered
wlan0: authenticate with AP 00:04:0e:d6:8e:e5
wlan0: authenticated
wlan0: associate with AP 00:04:0e:d6:8e:e5
wlan0: RX AssocResp from 00:04:0e:d6:8e:e5 (capab=0x411 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: no IPv6 routers present
fbcondecor: console 0 using theme 'livecd-2007.0'
fbcondecor: switched decor state to 'on' on console 0
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
ClusterIP Version 0.8 loaded successfully
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
IP: [<ffffffffa0ce801c>] 0xffffffffa0ce801c
PGD a7f69067 PUD a78b4067 PMD 0 
Oops: 0000 [#1] SMP 
last sysfs file: /sys/devices/system/cpu/cpu1/cache/index2/shared_cpu_map
CPU 0 
Modules linked in: iptable_raw xt_comment xt_recent xt_policy ipt_ULOG ipt_TTL ipt_ttl ipt_set ipt_REJECT ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE ipt_LOG ipt_ECN ipt_ecn ipt_CLUSTERIP ipt_ah ipt_addrtype nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_pptp nf_nat_proto_gre nf_nat_irc nf_nat_h323 nf_nat_ftp nf_nat_amanda ts_kmp nf_conntrack_amanda nf_conntrack_sane nf_conntrack_tftp nf_conntrack_sip nf_conntrack_proto_sctp nf_conntrack_pptp nf_conntrack_proto_gre nf_conntrack_netlink nf_conntrack_netbios_ns nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp ip_set_portmap ip_set_macipmap ip_set_ipmap ip_set_iphash ip_set xt_tcpmss xt_pkttype xt_physdev xt_owner xt_NFQUEUE xt_NFLOG xt_multiport xt_MARK xt_mark xt_mac xt_limit xt_length xt_iprange xt_helper xt_hashlimit xt_DSCP xt_dscp xt_dccp xt_conntrack xt_CONNMARK xt_connmark xt_CLASSIFY xt_tcpudp xt_state iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack iptable_mangle nfnetlink iptable_filter ip_tables x_tables aes_x86_64 aes_generic bridge stp llc snd_pcm_oss snd_mixer_oss snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device ipv6 coretemp btusb uvcvideo nvidiafb bluetooth compat_ioctl32 fb_ddc i2c_algo_bit videodev vgastate v4l1_compat nvidia(P) firewire_ohci arc4 firewire_core snd_hda_intel ecb iwlagn ohci1394 iwlcore snd_pcm snd_timer mac80211 ehci_hcd sdhci_pci ieee1394 video uhci_hcd snd_page_alloc r8169 snd_hwdep sdhci mii usbcore snd mmc_core i2c_core sg pcspkr intel_agp cfg80211 ac output serio_raw joydev button battery
Pid: 7706, comm: iptables Tainted: P           2.6.28-gentoo #2
RIP: 0010:[<ffffffffa0ce801c>]  [<ffffffffa0ce801c>] 0xffffffffa0ce801c
RSP: 0018:ffff8800a78f7c98  EFLAGS: 00010292
RAX: ffffffffa0ce8010 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8800a78f7d48
RBP: ffff8800a78f7ca8 R08: 0000000000000000 R09: 00000000fffffffe
R10: 0000000000000130 R11: 0000000000000000 R12: 0000000000000000
R13: ffff8800a78f7d48 R14: ffffc200121e430a R15: 0000000000000000
FS:  00007f112df6d6f0(0000) GS:ffffffff80867d80(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000a7878000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process iptables (pid: 7706, threadinfo ffff8800a78f6000, task ffff8800a7f04230)
Stack:
 ffff8800a78f7ce8 ffffffffa0ce84a0 ffff8800a78f7ce8 ffffffffa0b20a95
 00ff8800a928a8b0 ffff88013d462ae0 ffffc200121e4308 ffffc200121e3000
 ffffc200121e430a 0000000000000070 ffff8800a78f7da8 ffffffffa0b2864e
Call Trace:
 [<ffffffffa0b20a95>] xt_check_match+0xf5/0x180 [x_tables]
 [<ffffffffa0b2864e>] translate_table+0x30e/0x680 [ip_tables]
 [<ffffffffa0b29924>] do_ipt_set_ctl+0x124/0x1a0 [ip_tables]
 [<ffffffff805b83b0>] nf_sockopt+0x60/0xa0
 [<ffffffff805b842c>] nf_setsockopt+0x1c/0x20
 [<ffffffff805c5ad2>] ip_setsockopt+0xa2/0xb0
 [<ffffffff805e23e5>] raw_setsockopt+0x25/0x70
 [<ffffffff8058c53f>] sock_common_setsockopt+0xf/0x20
 [<ffffffff8058a06b>] sys_setsockopt+0x7b/0xe0
 [<ffffffff8020c2db>] system_call_fastpath+0x16/0x1b
Code: <0f> b7 39 e8 6c a0 ef ff 66 ff c0 74 13 8b 53 1c b8 01 00 00 00 85 
RIP  [<ffffffffa0ce801c>] 0xffffffffa0ce801c
 RSP <ffff8800a78f7c98>
CR2: 0000000000000000
---[ end trace 1996361bf1ecef21 ]---