Index: ipw3945-1.2.0/Makefile
===================================================================
--- ipw3945-1.2.0.orig/Makefile
+++ ipw3945-1.2.0/Makefile
@@ -26,20 +26,20 @@ CONFIG_IPW3945_DEBUG=y
 # NOTE:  If you have problems compiling due to IW_MODE_MONITOR not being
 #        defined then you need to update the wireless extension version
 #	 installed in your kernel, or comment this line out.
-# CONFIG_IPW3945_MONITOR=y
+CONFIG_IPW3945_MONITOR=y
 
 # If you are interested in using radiotap headers in monitor mode,
 # simply uncomment:
 #
 # NOTE:  To use RADIOTAP you must also enable MONITOR above.
-# CONFIG_IEEE80211_RADIOTAP=y
+CONFIG_IEEE80211_RADIOTAP=y
 
 # The above monitor mode provides standard monitor mode.  The following
 # will create a new interface (named raw%d) which will be sent all
 # 802.11 frames received on the interface
 #
 # NOTE:  To use PROMISCUOUS you must also enable MONITOR above.
-# CONFIG_IPW3945_PROMISCUOUS=y
+CONFIG_IPW3945_PROMISCUOUS=y
 
 # The following, if enabled, will add a sysfs entry 'rx' that raw
 # 802.11 radiotap formatted packets can be written to.  Those packets
@@ -186,34 +186,6 @@ utils:
 	@[ ! -d util ] || make -C util IEEE80211_PATH=$(IEEE80211_PATH)
 
 check_inc:
-	@( [ "$(IEEE80211_DUPLICATE)" ] && echo -e \
-"\n WARNING: Your kernel contains ieee80211 symbol definitions and you\n"\
-"are not using the kernel's default ieee80211 subsystem.  (Perhaps you\n"\
-"used the out-of-tree ieee80211 subsystem's 'make install' or have\n"\
-"provided a path to the ieee80211 subsystem via IEEE80211_INC.)\n\n"\
-"If you wish to use the out-of-tree ieee80211 subsystem then it is\n"\
-"recommended to use that projects' \"make patch_kernel\" facility\n"\
-"and rebuild your kernel to update the Module symbol version information.\n"\
-"\n"\
-"Failure to do this may result in build warnings and unexpected\n"\
-"behavior when running modules which rely on the ieee80211 subsystem.\n\n"\ || \
-	exit 0)
-
-	@( [ "$(IEEE80211_DUPLICATE)" ] && \
-	   [ ! "$(IEEE80211_IGNORE_DUPLICATE)" ] && echo -e \
-" Aborting the build.  You can force the build to continue by adding:\n\n"\
-"\tIEEE80211_IGNORE_DUPLICATE=y\n\n"\
-"to your make command line.\n\n" && exit 1 || exit 0)
-
-	@( [ ! "$(IEEE80211_API)" ] && echo -e \
-"\n ERROR: A compatible subsystem was not found in the following path[s]:\n\n"\
-"\t$(IEEE80211_RES)\n\n"\
-"You need to install the ieee80211 subsystem from http://ieee80211.sf.net\n"\
-"and point this build to the location where you installed those sources, eg.:\n\n"\
-"\t% make IEEE80211_INC=/usr/src/ieee80211/\n\n"\
-"or use the 'make patch_kernel' within the ieee80211 subsystem to patch your\n"\
-"kernel sources.\n" && exit 1 || exit 0)
-
 	@echo -e \
 " Using ieee80211 subsystem version API v$(IEEE80211_API) from:\n\n" \
 "\tBase: $(IEEE80211_BASE)\n" \