I am unable to burn a CD-RW using cdrecord on a system running 2.6.13-rc6 . I have not tried a CD-R. I get cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity. cdrecord is not suid. I am burning as root. brw-rw---- 1 root disk 22, 0 Oct 24 2004 /dev/hdc I can burn if I reboot into a 2.4 kernel. Reproducible: Always Steps to Reproduce: as root: 1. cdrecord dev=0,0,0 speed=1 blank=fast -v -tao ~thoth/music.iso Actual Results: Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 J
I am unable to burn a CD-RW using cdrecord on a system running 2.6.13-rc6 . I have not tried a CD-R. I get cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity. cdrecord is not suid. I am burning as root. brw-rw---- 1 root disk 22, 0 Oct 24 2004 /dev/hdc I can burn if I reboot into a 2.4 kernel. Reproducible: Always Steps to Reproduce: as root: 1. cdrecord dev=0,0,0 speed=1 blank=fast -v -tao ~thoth/music.iso Actual Results: Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling cdrecord: Warning: Running on Linux-2.6.13-rc6 cdrecord: There are unsettled issues with Linux-2.5 and newer. cdrecord: If you have unexpected problems, please try Linux-2.4 or Solaris. TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.5.33 Using libscg version 'schily-0.8'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 2 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'RW/DVD GCC-4243N' Revision : '1.07' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x000A Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A (current) cdrecord: Warning: controller returns wrong page 2A for Ricoh Vendor Page page (30). Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1601712 = 1564 KB Drive DMA Speed: 208103 kB/s 1182x CD 150x DVD FIFO size : 4194304 = 4096 KB Track 01: data 599 MB Total size: 688 MB (68:11.25) = 306844 sectors Lout start: 688 MB (68:13/19) = 306844 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11650 (97:26/50) ATIP start of lead out: 337050 (74:56/00) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 0 (reserved val 5) 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 3 A1 values: 02 4C B0 A2 values: 5A C8 38 Disk type: Phase change Manuf. index: 10 Manufacturer: Lead Data Inc. cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity. Expected Results: spend an hour burning a disc Portage 2.0.51.22-r2 (default-linux/x86/2005.0, gcc-3.3.6, glibc-2.3.5-r1, 2.6.13-rc6 i686) ================================================================= System uname: 2.6.13-rc6 i686 AMD Athlon(tm) 64 Processor 3000+ Gentoo Base System version 1.6.13 dev-lang/python: 2.3.5-r2 sys-apps/sandbox: 1.2.12 sys-devel/autoconf: 2.13, 2.59-r6 sys-devel/automake: 1.4_p6, 1.5, 1.6.3, 1.7.9-r1, 1.8.5-r3, 1.9.6 sys-devel/binutils: 2.15.92.0.2-r10 sys-devel/libtool: 1.5.18-r1 virtual/os-headers: 2.6.11-r2 ACCEPT_KEYWORDS="x86" AUTOCLEAN="yes" CBUILD="i686-pc-linux-gnu" CFLAGS="-O2 -march=i686 -fomit-frame-pointer" CHOST="i686-pc-linux-gnu" CONFIG_PROTECT="/etc /usr/kde/2/share/config /usr/kde/3.3/env /usr/kde/3.3/share/config /usr/kde/3.3/shutdown /usr/kde/3.4/env /usr/kde/3.4/share/config /usr/kde/3.4/shutdown /usr/kde/3/share/config /usr/lib/X11/xkb /usr/share/config /usr/share/texmf/dvipdfm/config/ /usr/share/texmf/dvips/config/ /usr/share/texmf/tex/generic/config/ /usr/share/texmf/tex/platex/config/ /usr/share/texmf/xdvi/ /var/bind /var/qmail/control" CONFIG_PROTECT_MASK="/etc/gconf /etc/splash /etc/terminfo /etc/env.d" CXXFLAGS="-O2 -march=i686 -fomit-frame-pointer" DISTDIR="/usr/portage/distfiles" FEATURES="autoconfig distlocks sandbox sfperms strict" GENTOO_MIRRORS="http://distfiles.gentoo.org http://distro.ibiblio.org/pub/Linux/distributions/gentoo" PKGDIR="/usr/portage/packages" PORTAGE_TMPDIR="/var/tmp" PORTDIR="/usr/portage" PORTDIR_OVERLAY="/home/thoth/portage" SYNC="rsync://rsync.gentoo.org/gentoo-portage" USE="x86 3dnow 3dnowext X Xaw3d acl alsa apache2 apm arts avi bash-completion berkdb bitmap-fonts bonobo bzlib cdr crypt cups curl divx4linux doc dv dvd dvdr dvdread edl emboss encode esd fam ffmpeg foomaticdb gd gdbm gif gnome gpm gstreamer gtk gtk2 gtkhtml guile imagemagick imlib inkjar ipv6 java jpeg junit kde libg++ libwww mad maildir matroska mikmod mjpegi mmx mmxext mng motif mozsvg mp3 mpeg mysql mythtv ncurses nls nojython ogg oggvorbis opengl oss pam pcmcia pdflib perl png python qt quicktime readline real samba sdl spell sse sse2 ssl svg svga tcltk tcpd theora tiff transcode truetype truetype-fonts type1-fonts unicode v4l vim-with-x vorbis win32codecs wmf xinerama xml xml2 xmms xv xvid yv12 zlib userland_GNU kernel_linux elibc_glibc" Unset: ASFLAGS, CTARGET, LANG, LC_ALL, LDFLAGS, LINGUAS, MAKEOPTS
using kernel 2.6.12-gentoo-r6 I get the following failure output: nile:501 # cdrecord dev=0,0,0 speed=4 blank=fast -v -eject -tao ~thoth/music.iso Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 J
using kernel 2.6.12-gentoo-r6 I get the following failure output: nile:501 # cdrecord dev=0,0,0 speed=4 blank=fast -v -eject -tao ~thoth/music.iso Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling cdrecord: Warning: Running on Linux-2.6.12-gentoo-r6 cdrecord: There are unsettled issues with Linux-2.5 and newer. cdrecord: If you have unexpected problems, please try Linux-2.4 or Solaris. TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.5.33 Using libscg version 'schily-0.8'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 2 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'RW/DVD GCC-4243N' Revision : '1.07' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x000A Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A (current) cdrecord: Warning: controller returns wrong page 2A for Ricoh Vendor Page page (30). Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1601712 = 1564 KB Drive DMA Speed: 201600 kB/s 1145x CD 145x DVD FIFO size : 4194304 = 4096 KB Track 01: data 599 MB Total size: 688 MB (68:11.25) = 306844 sectors Lout start: 688 MB (68:13/19) = 306844 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11650 (97:26/50) ATIP start of lead out: 337050 (74:56/00) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 0 (reserved val 5) 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 3 A1 values: 02 4C B0 A2 values: 5A C8 38 Disk type: Phase change Manuf. index: 10 Manufacturer: Lead Data Inc. cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity. Using 2.4 kernel I have success: scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.25 SCSI buffer size: 64512 Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling TOC Type: 1 = CD-ROM Using libscg version 'schily-0.8'. atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'RW/DVD GCC-4243N' Revision : '1.07' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x000A Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A (current) Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1601712 = 1564 KB FIFO size : 4194304 = 4096 KB cdrecord: Cannot get next writable address for 'invisible' track. cdrecord: This means that we are checking recorded media. cdrecord: This media cannot be written in streaming mode anymore. cdrecord: If you like to write to 'preformatted' RW media, try to blank the medi a first. Track 01: data 599 MB Total size: 688 MB (68:11.25) = 306844 sectors Lout start: 688 MB (68:13/19) = 306844 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11650 (97:26/50) ATIP start of lead out: 337050 (74:56/00) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 0 (reserved val 5) 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 3 A1 values: 02 4C B0 A2 values: 5A C8 38 Disk type: Phase change Manuf. index: 10 Manufacturer: Lead Data Inc. Starting to write CD/DVD at speed 4 in real TAO mode for single session. Last chance to quit, starting real write 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Performing OPC... Blanking PMA, TOC, pregap Blanking time: 45.104s BURN-Free is ON. Turning BURN-Free off Performing OPC... Starting new track at sector: 0 Track 01: 599 of 599 MB written (fifo 100%) [buf 99%] 4.1x. Track 01: Total bytes read/written: 628412416/628412416 (306842 sectors). Writing time: 1030.083s Average write speed 4.0x. Min drive buffer fill was 99% Fixating... Fixating time: 64.544s cdrecord: fifo had 9899 puts and 9899 gets. cdrecord: fifo was 0 times empty and 9812 times full, min fill was 79%.
can you please try with cdrtools-2.01.01_alpha01 ? What's the size of the iso ? Kernel 2.6.x has lots of problems with cdrtools you should force the use of overburning in case of the iso is bigger than the size of the CD-RW.
I can't even emerge cdrtools-2.01.01_alpha01-r2. During the configure stage of the build process: .. checking for Cygwin environment... no checking for mingw32 environment... no checking for EMX/OS2 environment... no checking for executable suffix... configure: error: installation or configuration problem: compiler cannot create executables. make: *** [incs/x86-linux-cc/rules.cnf] Error 1
i commited a fix that fix that issue. Please try with that version
still does not work. nile:242 # cdrecord dev=0,0,0 speed=4 blank=fast -v -eject -tao ~thoth/music.iso Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 J
still does not work. nile:242 # cdrecord dev=0,0,0 speed=4 blank=fast -v -eject -tao ~thoth/music.iso Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 Jörg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.5.33 Using libscg version 'schily-0.8'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 2 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'RW/DVD GCC-4243N' Revision : '1.07' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x0000 Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A cdrecord: Warning: controller returns wrong page 2A for Ricoh Vendor Page page (30). Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive DMA Speed: 15 kB/s 0x CD 0x DVD FIFO size : 4194304 = 4096 KB Track 01: data 600 MB Total size: 689 MB (68:17.72) = 307329 sectors Lout start: 689 MB (68:19/54) = 307329 sectors Current Secsize: 0 ATIP info from disk: Indicated writing power: 0 Is not unrestricted Is not erasable ATIP start of lead in: 5100 (01:10/00) ATIP start of lead out: -150 (00:00/00) Disk type: unknown dye (reserved id code) Manuf. index: -1 Manufacturer: unknown (not in table) cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity. nile:243 # cdrecord -version Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 Jörg Schilling
try to add this option to cdrecord "-overburn"
Still no joy. nile:245 # cdrecord dev=0,0,0 speed=4 blank=fast -v -eject -tao -overburn ~thoth/music.iso Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 J
Still no joy. nile:245 # cdrecord dev=0,0,0 speed=4 blank=fast -v -eject -tao -overburn ~thoth/music.iso Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 Jörg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.5.33 Using libscg version 'schily-0.8'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 2 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'RW/DVD GCC-4243N' Revision : '1.07' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x000A Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A (current) cdrecord: Warning: controller returns wrong page 2A for Ricoh Vendor Page page (30). Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1601712 = 1564 KB Drive DMA Speed: 165415 kB/s 939x CD 119x DVD FIFO size : 4194304 = 4096 KB Track 01: data 600 MB Total size: 689 MB (68:17.72) = 307329 sectors Lout start: 689 MB (68:19/54) = 307329 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11745 (97:25/30) ATIP start of lead out: 359363 (79:53/38) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 8 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 5 A1 values: 02 4C D0 A2 values: 4A D8 5A Disk type: Phase change Manuf. index: 40 Manufacturer: INFODISC Technology Co., Ltd. cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity.
try this cdrecord -force -v dev=0,0,0 speed=4 blank=fast -eject check if your device is really dev=0,0,0 please show us your -scanbus info
Again, no joy. nile:432 # cdrecord -force -v dev=0,0,0 speed=4 blank=fast -eject ~thoth/music.iso cdrecord: No write mode specified. cdrecord: Asuming -tao mode. cdrecord: Future versions of cdrecord may have different drive dependent defaults. Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 J
Again, no joy. nile:432 # cdrecord -force -v dev=0,0,0 speed=4 blank=fast -eject ~thoth/music.iso cdrecord: No write mode specified. cdrecord: Asuming -tao mode. cdrecord: Future versions of cdrecord may have different drive dependent defaults. Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 Jörg Schilling TOC Type: 1 = CD-ROM scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.5.33 Using libscg version 'schily-0.8'. SCSI buffer size: 64512 atapi: 1 Device type : Removable CD-ROM Version : 2 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'RW/DVD GCC-4243N' Revision : '1.07' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x000A Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 Profile: 0x000A (current) cdrecord: Warning: controller returns wrong page 2A for Ricoh Vendor Page page (30). Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1601712 = 1564 KB Drive DMA Speed: 165415 kB/s 939x CD 119x DVD FIFO size : 4194304 = 4096 KB Track 01: data 598 MB Total size: 687 MB (68:08.61) = 306646 sectors Lout start: 688 MB (68:10/46) = 306646 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Reference speed: 2 Is not unrestricted Is erasable ATIP start of lead in: -11745 (97:25/30) ATIP start of lead out: 359363 (79:53/38) 1T speed low: 0 (reserved val 0) 1T speed high: 4 2T speed low: 8 2T speed high: 0 (reserved val 10) power mult factor: 4 6 recommended erase/write power: 5 A1 values: 02 4C D0 A2 values: 4A D8 5A Disk type: Phase change Manuf. index: 40 Manufacturer: INFODISC Technology Co., Ltd. cdrecord: Data will not fit on any disk. cdrecord: Cannot write more than remaining DVD capacity. nile:433 # cdrecord -scanbus Cdrecord-Clone 2.01.01a03 (i686-pc-linux-gnu) Copyright (C) 1995-2005 Jörg Schilling Linux sg driver version: 3.5.33 Using libscg version 'schily-0.8'. scsibus0: 0,0,0 0) 'HL-DT-ST' 'RW/DVD GCC-4243N' '1.07' Removable CD-ROM 0,1,0 1) * 0,2,0 2) * 0,3,0 3) * 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) *
When I got rid of the "hdc=ide-scsi" argument to my kernel boot (in lilo.conf) I was able to blank and record a CD-RW using cdrecord dev=/dev/hdc speed=4 blank=fast -v -eject -tao music.iso I stumbled across some message that deprecated ide-scsi not long ago and it gave me this idea. I'm not sure of the best place to document this. The stuff that prints out at the end of emerge is bloody useless because all but the last package scrolls off the screen.
(In reply to comment #10) > When I got rid of the "hdc=ide-scsi" argument to my kernel boot (in lilo.conf) I > was able to blank and record a CD-RW using > > cdrecord dev=/dev/hdc speed=4 blank=fast -v -eject -tao music.iso > > I stumbled across some message that deprecated ide-scsi not long ago and it gave > me this idea. > Indeed it's deprecated you shouldn't even use it on 2.6 kernels > I'm not sure of the best place to document this. The stuff that prints out at > the end of emerge is bloody useless because all but the last package scrolls off > the screen. > No it's not useless but if you read our ML's and blogs you should know that we are going to change that soon(i hope) :).
